The Skoda Yeti crossover was presented in 2009. The car is equipped with gasoline engines with a TSI turbocharger from 1.2 to 1.8 liters with a capacity of 103 - 160 hp, atmospheric 110-strong 1.6 MPI engine and turbodiesels 1.6 TDI and 2.0 TDI with a capacity of up to 170 hp, 5- and 6-speed mechanical Transmissions, 6- and 7-speed robotic DSG gearboxes or a hydromechanical machine with 6 steps. The model has an anterior and all-wheel drive (with the Haldex coupling connected by the rear axle) version.
Which oil to fill in Skoda Yeti 1.8 depends on the operating conditions of the car.
Total Quartz 9000 5W40
Total specialists are advised as an oil for Skoda Yeti 1.8 TSI Total Quartz 9000 5W40, when the manufacturer specifies the required level of properties VW 502.00 / 505.00. This universal engine oil is great for engines with turbocharging and direct injection, and thanks to outstanding protective properties, this engine oil for Skoda Yeti 1.8 TSI reliably protects the parts of the engine from wear in the most difficult conditions of movement, including at urban, sports and off-road driving, as well as cold start. Special detergents and dispersing additives in its composition prevent the formation of deposits and retain the cleanliness of the motor. Total Quartz 9000 5W40 High Antioxidant Properties allow you to adhere to the maximum oil replacement intervals recommended by automakers in Skoda Yeti 1.8.
Total Quartz 9000 ENERGY 0W30
Synthetic technology Total Quartz 9000 Energy Total 0W30 Motor oil is characterized by high low-temperature fluidity, so it is recommended to use this oil in Skoda Yeti 1.8 TSI, which are operated in a cold climate. Low sprouting temperature ensures oil pumping even in a heavy frost and makes it easier for cold start. The characteristics of Total Quartz 9000 Energy 0W30 guarantee protection against wear and harmful deposits in any conditions and, moreover, reduce friction losses, which makes it possible to achieve a reduction in fuel consumption when using this oil for Yeti 1.8.
Total Quartz Ineo Long Life 5W30
Total Quartz Ineo Long Life 5W30 Mailed Motor Oil Butter Life 5W30 is recommended for Skoda Yeti with TDI engines of all modifications. It is designed for use in cars that meet modern environmental requirements and satisfies ACEA C3 and VW 504.00 / 507.00 standards. The special composition of Low SAPS with a low content of metals, phosphorus and sulfur compounds optimizes the operation of the scene filter and prevents its clogging and premature failure. This oil for Skoda Yeti can be used in any operating conditions and guarantees a high level of protection against wear and deposits. The durability of Total Quartz Ineo Long Life 5W30 to oxidation allows, in accordance with the automaker's recommendations, increase the oil replacement interval.
It makes no sense to overpay maintenance station workers for planned replacement of engine oil and related filters. It is enough to do this not a tricky work once and next time you will already be a specialist. And we will certainly help you in small nuances of this non-intricate problem.
How much pouring (filling volumes)
- Engines 1.2 and 1.4 L - 3.6 l
- Engine 1.8 L - 4.6 liters
- 2.0 l - 4.3 liters (only 507 tolerance)
Before starting work, make sure that you all bought and have at hand:
- New oil;
- Oil filter;
- Rags;
- Tazik on ~ 5 l;
- Key for removing protection and drain plug;
Work stages
- Warm the cold engine 3-4 minutes. Cold oil wakes badly to flow from the engine, as a result there can be a lot of dirty oil that in the end you mix new. Thus deteriorate the characteristics of the new oil.
- We put the car on the jacks either on the observation pit (perfect option) for convenient access to the bottom. In some models, the "protection" of the engine crankcase can be installed. It needs to be removed to access the drain plug.
- We unscrew the plug of the fuzzy neck, take out the oil probe. Oil faster merges if there is a through hole.
- We substitute a basin or any other dishes that can accommodate 5 liters of work.
- We unscrew the drain cork with the key (better if the ratchet wakes). It is best to immediately expect that the oil wakes up hot. At this stage of work, you need to be most attentive.
- After a complete drain of old dirty oil that has a black color, we remove the basin aside.
- An optional point is washing the engine with a special flushing fluid. You will be surprised at which black oil will fall out with this liquid. Use this liquid is very simple. Pour into the engine, pre-tighten the drain plug of course. We start the car for 3-5 minutes. At the same time, we chase and warm our liquid on the old oil filter. After, wasting and merge into a free container.
- We change the oil filter to a new one. Before putting a new filter, pour about 100 g of fresh oil into it and also lubricate the rubber sealing ring on it.
- Pour new oil. Making sure that the drain plug is spinning, and the new oil cleaning filter is installed. We can start the fill of the new oil focusing on the pouch. The level should be between the minimum and maximum mark. Also, you need to remember that after the first start of the engine, some oil leaves and the level goes down.
- Re-check the oil level on the PCU after the first start. Let the engine work for about 10 minutes at idle.
What oil pouring
- Oil type - synthetics
- Summer - 20W-40, 25W-50
- All-season - 10W-50, 15W-40
- Winter - 0W-40, 5W-50
- Recommended Brands - Shell, Mobile, Castrol, Lukoil, Xado, Valvoline, Zic, GT-Oil
Video materials
What oil to use to replace and when?
Oil for these motors use only with tolerances VW 504 00; 507 00., as well as viscosity 5W-30. By regulations, oil replacement is made every 15,000 km or every 12 months . Under our operating conditions, we recommend replacing the oil every 8 000-10 000 km or every 12 months in .
Spare parts necessary to replace oil:
Original spare parts:
Analogs of spare parts:
* - Miscellaneous oil packing is indicated, both items should not be purchased.
The cost is approximate and indicated for 2017.
Replacement procedure on Skoda Yeti 1.2 TSI CBZB:
1. Under the hood we open the lid of the oil refining neck.
2. pull out the oil probe, not completely, in order to get air. 
3. Weaken the oil filter, but do not remove, we give the remaining oil in the filter. 
4. Remove the protection of the engine crankcase, unscrew the screws of the mounting of the hides, and then the fastening bolts of the protection itself. 
6. Let us drain the oil. We drag up to the moment slow drop drops of oil. 
7. Spinning new Drain plug and tighten with a point of 30 nm. 
8. We are cluttered from the oil drain plug and the adjacent part of the pallet. 
9. We install the Carter protection. 
10. Remove the oil filter.
Pay attention to the oil filter bracket, it may remain a filter seal, as in our case, it must be deleted.
11. Remove the oil filter seal. 
12. Water from the old oil seat of the oil filter. 
13. Install a new oil filter and tighten the point of 20 nm. 
15. Pour new engine oil into the engine.
Approximate volume of oil with a 3.6 liter oil filter replacement.
16. We wipe the planting place of the oil-tapping neck cover. 
17. Close the oil refining neck. We climb the valve cover if the oil was shed. 
18. We start the engine, give him to work 2-3 minutes, then wasting and give to stand 3 minutes in order to glass oil. We look at the oil level, if the oil level is slightly higher than the middle, then the oil does not fill, if not, it is necessary to add oil.
From the MIN mark to MAX mark, approximately 0.7-0.8 liters of oil.
The engine on the Skoda car over time is subjected to wear and deformation. To prevent this process, it is necessary to competently select engine lubricant according to tolerances and specifications from the manufacturer. High-quality oil will not only provide the functional performance of the system, but also protects it from damage.
What tolerances on Skoda different models
Skoda Rapid
Czech manufacturer Indicates a lubricant VW Long Life III Lubricant with a viscosity of 5W30 for Skoda Rapid models with capacity and volumes of engines:
- 122 hp TSI - 1.4 l;
- 86, 105 hp TSI - 1.2 l;
- 105 hp TDI - 1.6 liters.
For more powerful power units, the manufacturer recommends the VW Special Plus 5W40 oil. It is poured into atmospheric engines installed on rapid.
At the factory, a new car released from the conveyor is poured Volkswagen's branded lubrication with tolerances 502 and 504. When executed, experts can offer auto-oil with other specifications and tolerances. For example, in Skoda service centers can offer oils from brands Shell, Mobile or Castrol.
Skoda Octavia
In the power units of Octavia A5, the manufacturer recommends pouring products on a synthetic basis. As for tolerances, they must comply with the standards of VW 502/504/505/507. Viscosity - 5W40, 5W30. However, when performing, the 0W30 lubricant is poured. Car enthusiasts prefer:
- Motul 8100;
- Castrol EJ;
- Shell Helix ultra;
- We are sitting about;
- X-wedge;
- Liquida moth.
- TDI 2.0 - 3.8 l;
- TDI 1.9 - 4.3 l;
- TSI 1.8 - 4.6 liters;
- TDI 1.6 - 3.8 l;
- MPI 1.6 - 4.5 liters;
- TSI 1.4 - 3.6 l;
- TSI 1.2 - 3.6 liters.
According to technical regulation, the oil change is carried out after 15 thousand km of mileage or earlier, depending on operational conditions.
Octavia 7.
In the instruction manual, it is indicated that for cars with a flexible replacement interval, it is necessary to pour oils with VW 504 tolerances if the engine has a volume of 1.2-1.4-1.8 liters and is equipped with a turbine.
In turbocharged engines with volumes of 1.6 and 2.0 on diesel fuel, it is recommended to fill VW 507. If a limited interval is installed on the car, lubricants with tolerances 502 are installed for gasoline.
Czech manufacturer by default flooding Skoda Octavia 7 Castrol EDGE 5W30 car. It corresponds to the tolerances of Long Life III, which may be indicated on the canister together with specifications from Volkswagen.
After passing, the car enthusiasts prefer to change the branded lubricant on alternative analogs from manufacturers:
- Mobil;
- Shell;
- Motul.
The viscosity index is selected based on the operational conditions and temperature indicators of one or another region.
Speaking of replacement periodicity, it is necessary to proceed from the tolerances used. It is best to replace the car to achieve 10-15 thousand km of mileage.
Volumes of filling fluid in motors:
- TSI 1.2-1.4 - 4.2 l;
- TSI 1.8 - 5.2 liters;
- TDI 1.6-2.0 - 4.6 liters.
Oktavia tour
The replacement interval for OTC systems Octavia TUR is from 10 to 15 thousand km, depending on the operating conditions. The manufacturer recommends a synthetic-based lubricant with an index 5W30 or 5W40 depending on the parameters and volume of the engine.
The amount of oil poured is up to 5 liters. As for tolerances, the product must correspond to the VW 503-504. More than old versions of VW 501-502 may also be suitable.
Skoda Superb
Volkswagen car concern uses factory oil on a synthetic-based 5W30 for SKODA Superb engine systems. It corresponds to the tolerances of Long Life III VW. This almost the same lubricant as Castrol SLX. In the service centers in the motors pour lubricant on the synthetic database from the producer of the shell.
You can pour the car and from other manufacturers. The main indicator is the compliance of the tolerances of 502-504 and the viscosity classes of 5W40, 5W30. Also, do not forget about the periodicity of the oil replacement recommended for the engine systems equipped with turbocharging. If the superb model has 2.0 TDI engine, then it is better to use the 5W30 crawler with a tolerance of 507.
Lubrication with VW 504 tolerances must be used when running 15 thousand km. Some car enthusiasts prefer to replace the replacement after 10 thousand km. The regulation allows an earlier replacement if the car is operated in harsh climatic conditions.
Tolerance Skoda Yeti
For the power units set on Skoda Yeti, the original grease GM DEXOS 2. It corresponds to the tolerances VW and LL. The packaging indicates the following tolerances:
- VW 504;
- VW 501;
- VW 502.
In service centers for atmospheric engineering systems of 1,6 MPI, operating on gasoline fuel, use Shell Helix or Edge Castrol with 5W30 viscosity indices. Such power units correspond to the tolerances VW 502/504/505/507. Experts also offer to upload motor lubricants from manufacturers:
- Motul 8100 5W40;
- Total 9000;
- Liquida moth.
Staying on the selection, special attention should be paid to specifications and viscosity. As a rule, 4 liters are used for Skoda Yeti engines. Replacement is performed based on climatic conditions. Recommended frequency - 10-15 thousand km run.
Oil in the engine system Skoda Fabia
The engine fluid on the Skoda Fabia model must have a VW 502-505 tolerance and a 5W40 or 5W30 viscosity degree. Recommended Castrol EDGE.
You can also pour the compositions on a synthetic basis with the viscosity index of 0W30. In service centers, Skoda, specialists use such oil for Fabia with an engine capacity of 1.4.
