One of the reasons for unsatisfactory manageability and coursework stability of UAZ-3163 cars, the patriot may be fault in the steering or the presence of hollows and gaps in pivot nodes.
Faults affecting manageability and coursework UAZ patriot.
One of the possible faults, this is an overwhelmed moment of rotation of the tower of the steering mechanism when the input shaft is released - it should be within 2.5-3.5 kgf / m for the UAZ-3163 patriot.
The total torque moment when rotating controlled wheels with a disconnected steering mechanism should not exceed 12 kgf / m. This moment is provided by adjusting the squava nodes, the presence of a sufficient amount of lubricant in pivot nodes, tips of the steering, hinges of equal angular velocities, wheel hubs.
If the swivel fist was disassembered with the replacement of liners, a kinstone, and so on, then when it is assembling, it is necessary to adjust the preload along the total axis of the kingle and the correct mutual position of the ball support with the pivot casing to prevent the ball joint. Torque rotation of the ball support in any direction relative to the total axis of the knevore should be within 1.0-1.5 kgf.
The controllability and course stability of the car may be unsatisfactory and due to the malfunction in the form of underestimated values \u200b\u200bof the longitudinal angles of inclination, the corner of the caster. In a fully loaded car, according to the factory requirements, the longitudinal angle should be at least 6 degrees for UAZ patriot. The difference in the corners of the longitudinal tilt of the pvsore should be no more than 1 degree. The decrease in these angles may occur as a result of a car suspension elevator.
Bad handling can be due to poorly fixed cross-stability stabilizer or due to the insufficient moment of tightening bolts and nuts of the longitudinal and transverse front suspension rods - the required moment must be within 14-16 kgf / m. The moment of tightening nuts of the finger tips of the steering should be within 4.9-6.9 kg / m, and the tightening torque of the steering bolts to the frame is 5.6-8.0 kg / m.
Also unacceptable hopes in:
Tips steering
- Crosses and Slots of the Steering Tree,
- steering mechanism when the controlled wheel is the corresponding movement in a straight line,
- places connecting the fingers of the tips of the steering tag with a bump, forged lever, swivel fists,
- pivot nodes and wheel hubs.
The convergence of the front wheels UAZ Patriot.
It may affect the controllability and coursework stability of the car and incorrectly adjusted front wheels convergence, for the type bridge it should be in the range of 0 ° 1'32 '' - 0 ° 4'36 '' for each wheel or 0 ° 3'04 '' 0 ° 9'12 '' Total. In the absence of a special stand, it is allowed to check and adjust the convergence of the wheels along the inner surfaces of the tire.
For full-fledged work with autotochki, your browser must support JavaScript. Turn it on in the settings.
- 5
Moscow, Aviators Street, 13c6 - 5
Moscow, street bottom fields, 29c16 - 5
Moscow, Michurinsky Prospekt, 31k7 - 5
Mytishchi, Novomytishchi Prospekt, Vl5 - 5
Moscow, modele pass, 8c17 - 5
Odintsovo, Mozhayskoye Highway, 10 - 5
Moscow, Pyazovaskaya Street, 7 - 5
Moscow, Warsaw Highway, 170g, boxing number 30 - 5
Moscow, marching passage, 5k1 - 5
Moscow, SOVOGO STREET, 10As2 - 5
Shcherbinka, Simferopol highway, 16 - 5
Moscow, Street Steelhelov, 14C1 - 5
Moscow, Highway Travel, 10K1 - 5
Moscow, Zavaruyevsky Lane, 32c4 - 5
Krasnogorsk, Station Street, 37 - 5
Balashikha, Avtozavodskaya Street, 50a - 5
Moscow region, P. Barvikha, Pushkinskoye highway, 41 - 5
village Milkovo - 5
Moscow, MKAD, 78th kilometer, Vl2 - 5
Moscow, Gorbunova Street, 12k2c2 - 5
Moscow, Street Gardeners, 11Ak1 - 5
Mytishchi, Street Rifle, Boxing 88 - 5
Balashikha, Nosovykhinskoe highway, 26 - 5
Balashikha, Ceramic Street, 2a - 5
Moscow, Dnepropetrovsk passage, 7 - 5
Dolgoprudny, Few Street, 3a - 5
Moscow, Kasimovskaya Street, 2 - 5
Moscow, South Street Street, 9C2 - 5
Moscow, Polar Street, 39 - 5
Moscow, trade union street, 145 - 5
Balashikha, Lenin Avenue, 73 - 5
Moscow, Warsaw Highway, 265/90 - 5
Kotelniki, Promzone Street Silicat, 9/1 - 5
Moscow, Novostapovskaya Street, 6As12 - 5
Moscow, Plekhanov Street, 10 - 5
Moscow, Lake Street, 46K2 - 5
Moscow, Central Union Street, 10As9 - 5
Moscow, Persian Street, 71 - 5
Lyubertsy, Egoryevskoe highway, 7V - 5
Moscow, Pine Alley, 4C3 - 5
Moscow, Kashirskoye Highway, 67С5 - 5
Lyubertsy, Street 65 years Victory, 1litp - 5
Moscow, Aviamotornaya Street, 67 / 8c - 5
Moscow, traveling passage, 13c4 - 5
Moscow, Minsk Street, 1m - 5
Khimki, Kurkinskoe highway, 13k2c1 - 5
Balashikha, Highway Enthusiasts, Vl1 - 5
Moscow, projected passage number 6604 - 5
Moscow, Volgograd Prospekt, 32K11
- ← previous
Skhod-collapse UAZ in Moscow - Prices
- Hello, dear Vitaly!
Thank you for your interest in the company "AVTOGERMEM"!
The value of the gathering of the collapse on 2 axes of 3200 rubles.
The nearest entry to the Sormovskaya 21A technical center on 08.28.19 from 15:00 day.We draw your attention to the fact that now for the owners of the UAZ car in our dealership, the following proposal is valid:
Special offer of anti-corrosion coating of wheeled arches for cars with mileage!
Wheel arches are one of the most vulnerable places of the car.
They are maximally subject to watercourse and abrasive wear. In winter, they experience the impact of the "salt fog" resulting from the use of reagents.And the arch is the main source of noise in the cabin. Vibration is transmitted through them, which is transformed into a hum of irritating driver and passengers.
Integrated wheel arches processing service solves several problems at once:
Reduces noise for 4 dB (twice)
- prevents rust formation and blocks already started corrosion foci
- protects the surface from the impact of road gravelFor processing wheel arches, we use PRIM Antisheum RS autocreparations. They are designed specifically for cars with mileage and form a durable protective layer with a service life of up to 12 years.
The service sprayed noise insulation is not only a comfortable driving, but also a reasonable contribution to the future of your car.
Cost of application 6 500 rubles.
We invite you to visit our dealership "AVTOGERMEM", located at
Sormovskaya 21 a.
For a guaranteed visit to our dealership in a day and time convenient for you and time, we suggest you to use the service provider on the total telephone number of AVTOGERMEM.We will be glad to see you in the Avtotechnames dealer center, located at Moscow, ul. Sormovskaya, d.21a, p. 9!
Opening hours: Technical Center
Mon. from 8:00 to 21:00
Driving directions: - Good afternoon, the collapse of 2000 rubles if everything is normal spinning without additional work
- on two axes cost 3000 rubles
- Good evening! Gathering collapse 2025 rub. Recording by phone, from 9-00 to 20-00
- Go fuck the trash do not
- Maxim: trash your service. And the mechanics there are hands, and the administration - goats from the mountains fallen.
- Go Warm 😂😂😂😂
- Maxim: What do you have to steal?
- The cost of adjustment of the 1st axis is 1600 rubles., Record by phone.
- On Monday you can do, the price of 2000 rubles
UAZ Patriot 2014, wheel alignment
Nikolay: Price to repair the collapse of convergence
- One axis 1500.
- Good afternoon, dear client. We are glad that you appealed on this issue to Fit Service! Your request is processed, and we are ready to provide all the services that interest you. I would like to draw your attention to that before performing any work with the car, we recommend that you make the diagnosis of all nodes and identify only what really needs to be replaced, it will save you to save money and time. We remind you that all purchased and installed spare parts we provide a guarantee of 1 year. Please inform us your phone number so that we can reserve a convenient date and time for you. Also there is an option to independently sign up from our site and get an additional discount of 3%. Also, we are always welcome to your phone call. With hope for cooperation, team of professionals Fit Service.
- Good morning. The collapse of the convergence costs 2050 rubles. Record by phone
UAZ HUNTER 2011, alignment
Vladimir: Making a similarity called after the replacement of a pussy
- Good day!
1500 The gathering collapse for one axis.
2500 for both axes.Respectfully,
Motogur. - 2000 work
- Good morning! Unfortunately to your car, we do not have a program with data and testimony! I recommend contacting another maintenance center.
Sincerely, Alexander.
- Good day!
- Moscow, passage Olminsky, 6c1
from 1800 r. UAZ Patriot 2015, wheel alignment
Artyom: gathering collapse. Urgently.
- Good afternoon) Short camber 1500
- 2200 work on the collapse
- Hello, Artem, we are temporarily not doing.
- Call
- the gathering can only be done on Saturday
- Hello, Artem! The cost of similarity-collapsed 2000 rubles per axis, 2500 rubles 2 axes. Notify that you are with a lot of car, 10% discount will be provided. Car service "GoodZone" Balashikha, Star Street, Vl1,
UAZ 3163 2017, disorder
Maxim: price and perhaps additional work ..
- 2500 rubles
- Good day!
If required add. Repair, then their spare parts will be necessary.
Approximate cost of about 2500 rubles.
Warranty 14 days.
It is necessary to sign up in advance.
UAZ 3741 2016, alignment
Vladimir: gathering the collapse Price on UAZ Buanka
- Good day!
The cost of work is 1600 rubles.
Call! - Hello 2000 R.
- Good day!
The cost of work is 1600 rubles.
Call! - Good day! The cost of adjusting the corners of the wheel installation of 3000 rubles. You can sign up to the technical center by phone. Sincerely, a group of companies AVTOGERMES!
- Good day!
UAZ 3163 2015, alignment
Alexey: Make a gathering camber.
- 1600-00 rubles
- Hello, alas, temporarily do not.
- We do, call
- 1200 rubles
- Hello gathering collapsion on your car will cost from 1500r, depending on how the bolts go
- Good afternoon, Alexey.
Without body elevator, in the standard configuration, the gathering camber will cost 2500 rubles.
Notify that you are with autotop, a 10% discount will be provided.
Car service "GoodZone" Balashikha, Star Street, Vl1
,
UAZ Patriot 2012, wheel alignment
Evgeny: convergence by car UAZ Patriot
- Good evening! We produce work on the request required. The price of work is one axis 2000r, for two axes -3000r
UAZ Patriot 2006, alignment
Alexander: Make a convergence on UAZ Patriot 2006.
- Car service "Bosch Auto Service H2O-Auto Alekseevskaya": Thank you very much for your appeal. We will be happy to advise you by phone: daily from 9.00 to 21.00
- Adjustment of the collapse of the convergence - 2500
- Alexander: Only convergence is made on UAZ, you offer the price for the full range of works of ordinary passenger cars.
UAZ Patriot 2015, wheel alignment
Dmitry: The collapse of the convergence. Territorial Yuao, Yuvao
- Good day! To date, the cost of the approach is 990 rubles. You can find out more information and sign up to the technical center by phone. Sincerely, a group of companies AVTOGERMES!
- Good day! To clarify the possibility and cost of work - Phone with our master master
And also visit our website and the VC group for more information.
https: //xn----7sbbbi1a3brl.xn--p1ai/
UAZ 3160 2012, alignment
Valentine: adjust the breakdown
- Good day! The cost of work will be 1500r. Sign up at a convenient technical center for you by phone. Sincerely, a group of companies AVTOGERMES!
- Good day!
I am pleased to answer more detail on your car service request. To do this, please click on the link to our site
There is a convenient form of an application for repairing a car, within an hour you will begin to receive answers from car services with auto service offers.
You can also get acquainted on the main page with the "Best Discounts" section and write to a specific car service.
Thank you for your request, we will be happy to help with the application of the application at the Uremont at the number:
Command - You can also get acquainted on the main page with the "Best Discounts" section and write to a specific car service. Alexander: Good day! It is necessary to make the collapse of the leaving loaf, with non-standard wheels. Interested in the cost of the work and the time that the procedure will occupy ... Mandatory in Swao !!! Thanks in advance!!! Communication by mail !!!)))
- Good day!
In this case, on a / m VAZ 2104, the collapse will cost a 1200r.
We inform you that the technical center at the address of the spiritual lane, 17 A, moved to Warsaw highway d. 125 p. 19
You can find out detailed information and sign up to the technical center by telephone with respect, the Group of Companies AutoChermes!We will try to make you a profitable offer and we will be glad to see you in our company.
We accept customers by appointment. - We apologize, the answer sent to you wrong!
The answer to your question: on a car in this version, there is no technical ability to adjust the WF. Sincerely, a group of companies AVTOGERMES!And finally, the convergence. We are talking about the total context (the amount of the angles between the longitudinal axis of the machine and the plane, which passes through the center of the right and left wheels). First for the front wheels. A plus of positive convergence is stability at high speeds, and a minus is an increase in insufficient turning. The advantage of negative convergence is the improved reaction of the wheels on the movement of the steering wheel, and the minus is rapid wear of rubber, the transfer of the irregularities of the road to the steering wheel, or simply "beating". As for the rear wheels, the situation is almost the same. If you do a negative alignment, then the car will be inclined to drift. The most optimal is to drive a car with zero consension on both axes.
The geometry of the wheels is what the driver's life depends on. Wrong similarity-collapse UAZ strongly changes the characteristics of the car. Moscow, as a major city with complex driving conditions, makes the gathering collapse even financially with a problem - with incorrect settings, tires are rapidly wear. Computer similarity-collapse UAZ, or rather - modern services for the diagnosis and adjustment of the geometry of wheels - a lesson requiring high qualifications and accurate equipment. Not all technical center performs the gathering collapse qualitatively.
The workplace of the UAZ scattering specialist should ensure the horizontal position of the vehicle when the corners are adjusted and the wheels are installed uniform loading of the suspension. Unfortunately, the average lift always has a small batch, sometimes constituting several degrees. Is it harmless if the suspension deflection is practically not happening at small skews of the lift? No, even 1-2 degrees of "neuronsality" lift lead to 1-2 degrees of error in measurements due to the gravitational principle of measurements of most stands. If we consider that, for example, a complete tolerance for the collapse of the wheels on modern cars does not exceed 30 minutes (half generators), the error of the lift of 1-2 degrees is fatally affected on the results of measurements and adjustments.
What does it indicate the need to carry out the similarity-collapse of the UAZ?
. An input or steering wheel has changed its position when moving in a straight line.
. The car holds the road badly (I dig).
- Good day!
UAZ Patriot 2016, wheel alignment
Vitaly: the gathering collapsed on 2 axes, after replacing the pivot.
Maxim: Make the wheel alignment.
Andrei: OZA convergence Patriot Address Price
Check and adjusting the angles of the wheel installation are necessary to ensure good stability and controlled car, as well as uniform wear of tires during operation.
Verification and adjustment of wheel installation angles are performed on special stands according to instructions for their operation.
The inconsistency of the actual values \u200b\u200bmeasured by car, the control values \u200b\u200blisted below can be explained by wear and deformation of the pendant parts, body deformation.
Replacing or repairing the parts of the suspension can entail a change in the angles of the wheel installation, so checking the angles of the wheel installation after these works are required.
Verification of wheel convergence is carried out by measuring the distance between the middle parts of the sidewalls. Distance BUT
Between wheels in front should be 0.5-1.5 mm less than the distance AT between wheels from behind.
The convergence of the front wheels is regulated by changing the length of the rug trapezium.
To adjust the convergence, follow these operations.
Loosen the tightening of nuts and the rotation of the adjusting thrust, achieve the correct wheel convergence, after which tighten the batteries.
Checking the angles of maximum rotation of the wheels are carried out on the stand.
The angle of rotation of the right wheel to the right (left wheels left) should be within 26-27 °.
The rotation angles of the front wheels adjust the rotation of the stubborn bolt 1 having pre-weaken the tightening of the battery nut 2 .
Each car owner more than once heard such terms as the collapse. These terms mean the need for repair, which may be needed at any per minute. This requires such a repair in the poor-quality road surface or the operation of the car in harsh roads. Actually SUV OAZ Patriot and is intended for such aggressive operating conditions, so every car owner of the all-terrain vehicle needs not only to know what collapsing is, but also to be able to adjust with their own hands.
Appointment of wheel convergence
The need to check and adjust the convergence, as well as the collapse of the wheels occurs after repair work was carried out with the running part. You should also visit a hundred after driving in large pits or bumps at speeds that lead to the violation of the integrity of the chassis. But even if the UAZ Patriot car is operated exclusively on smooth roads, then even in this case it is necessary to periodically visit a hundred or engage in the adjustment of the collapse-convergence.
Another sign of incorrect convergence is the uneven wear of the front wheel tread. If you notice that the protector is closed on the one hand, it means urgently need to be adjusted.
The convergence is a parameter in which the wheels are in a mutual position relative to each other. If this parameter violates this parameter, the asymmetric wheel position relative to each other is detected. At the same time, they are spread in different directions, which negatively affects the driving part of the car and rubber.
Special adjustment device (ruler)
The collapse and gathering are two completely different parameters, but which are held on the service station together. To learn that on the UAZ SUV patriot, it is necessary to adjust the convergence easily. To do this, you need to go on a flat and smooth track and at a speed of 60-80 km / h to let go of the steering wheel. In this case, if the car goes to any side, then the adjustment is urgently required. Otherwise, untimely adjustment will entail failure of the components of the car suspension UAZ Patriot. But as you know, the first to take on the whole impact of such a fault is the tires. It all begins with the rapid erase of the protectors in one or another part of the rubber. In addition, it is negatively reflected on the wheels, their curvature is observed. To imagine visually, which represents the collapse, and that convergence is presented below the sketch.
The collapse is called an angle to which the plane of the wheel deviates from the vertical. The collapse on the UAZ patriot is not regulated - only adjustment, repair, or replacement of a kingnery is produced.
Self adjustment
Corners of collapse and convergence on the SUV of UAZ Patriot can be adjusted independently at home, while saving a considerable amount of money. In addition, this procedure is recommended to be performed periodically, but not less than 1-2 times a year. This will save your car from serious breakdowns and the need to acquire new rubber.
So, if you have decided that you need to adjust the collapse and convergence by car, then the first thing should be verified in the serviceability of the chassis. If there is a need to repair or replace the suspension parts, then it is simply pointless to adjust the angles of the installation angles.
Finding out that the chassis does not need to be repaired, you can proceed to the procedure for adjusting the angles of the wheel installation. First you need to find a flat place where such events will be held. SUV UAZ Patriot should be released from excess weight and check tire pressure. This is very important, because these parameters can be incorrect adjustment.
Using caliper in measurements
We proceed to the operation of adjusting the angles of the wheel installation and perform the following actions:
- Initially, it is necessary to install the steering wheel in a straightforward position, thereby aligning the wheels.
- Before adjusting the gathering, it is necessary to put marks from the inside of the wheel in front of the wheel. Marks need to be applied to discs.
- You need to take a special bar (ruler) for measuring the distance between the inner surface of the tires.
- The ruler needs to be overtaken between two wheels in marked points. In this case, the ruler should not touch the parts of the car.
- You need to fix the distance on the line.
- Now you need to roll the car forward and measure the range of the distance in the back of the wheels, by the same points. In this case, the ruler should not touch the parts of the body and the suspension.
- Indications are checked.
- It is necessary that when measuring, the distance in the front part was 1-1.5 mm less than in the rear.
- If the distance between the wheels in the rear position is less than in the front, then it is necessary to lengthen the steering thrust that align the values.
- If the values, on the contrary, more, then the thrust should be shortened.
- If deviations are not exceeded with 1.5 mm, then the rotation of the wheels can be considered complete.
Adjust the wheel alignment on UAZ 3303, in other matters as on other models 469, 452 "Buka", etc. simply. In addition, unlike passenger cars, the collapse on the UAZ is not done.
Perhaps, perhaps, why it is impossible to adjust the collapse on the UAZ 3303. The fact is that this parameter is laid in the design of the machine, namely into the swivel fist.
If you do not have a hub on the hub, and the hub bearings are normally tightened, then this parameter will be all right.
It all started with the fact that the steering wheel began to go back to its original position, but the worst thing is that the car began to scour on the road. At the same time, it could not be not manifested on the level, but if irregularities appeared or especially Karai.
Tools
For repair, you will need:
- Key for 30;
- Key on 27;
- Rail.
Adjusting wheel convergence on UAZ 3303
It is important! Adjusting the convergence of the front wheels UAZ 3303 is performed at normal tire pressure. The tips of the steering thrust must be fit and without a backlash. Adjustment is reduced to the distance and in front of the distance in 1.5 - 3.0 mm at the back.
Verification of wheel convergence is usually made along the inner surface of the tires. But considering that the side of the tires is significant, the convergence can be adjusted incorrectly. Of course, it is best to adjust on the stand, but before you always did it yourself. In this case, when adjusting the convergence, we make two measurements, one between the tires, the second between the discs. The difference when measuring in the second case should not exceed 1.5 - 2 mm.
Before starting the adjustment, it is necessary to prepare a bar for measurements. For this you need a small wooden rail and caliper. Secure all this as in the photo. The caliper acquired inexpensive, plastic. You can do without a caliper, a ruler, for example, fastening it with rubber bands and putting tags.
Adjusting the wheel convergence is made by changing the length of the steering thrust. For this, lock nuts with the right and left thread and the rotation of the adjustment fitting are released in advance, change the length of the thrust.
- Levy with left thread; 2. Adjustment fitting; 3. Locking tire with the right thread; 4. Hinge.
The car is installed on a flat pad, make a frozen in the middle of the wheel height, at the touch points of the touch. Then roll the car, half of the circumference and re-stamped already behind. The difference between them will be the magnitude of the wheel convergence.
For confidence in the correctness of the adjusted convergence of wheels on the UAZ, it can be re-carried out at other points.
The tips of the steering should be fit and no backlash.
