Instructions for managing the machine on the mechanics. Tutorial for independent driving driving

Driving training on mechanics - Complex and long process. After all, the newcomer driver is difficult to turn the steering wheel at the same time, to switch the transfer, to press on the pedal, and also look at the box or pedal, but on the road. But any skill is a matter of practice.

The first driving lessons on mechanics may seem like "Justice Hell", but after a while, all movements and reactions are practiced to automatism and the driver performs all actions "on the reflex".
Therefore, we recommend to burn out on our, with an experienced instructor the learning process will be much easier! And this can be done very simply by filling out the following form:

Thank you!
Your application has been sent successfully.

I am waiting for a call

To learn how to drive on mechanics, of course you can get to read the reading of literature and textbooks, like "Driving on mechanics for beginners"But better than an experienced instructor, no one will explain all the subtleties. Therefore, it makes sense to contact a specialized driving school and passdriving lessons on mechanics Under the closer supervision of professionals.

Terms and cost of training

Training time for preparing for the examination of the category B component of 2-2.5 months

What is a manual gearbox (MCP)

MCP, often, has 5 speeds and rear gear. Let's consider in more detail what they need:

Neutral transmission. In this position, the handle of the transmission on the wheels is not transmitted torque. Even if you hit the gas pedal, the car does not touch. The appointment of this transmission is a continuous car parking with an engine. You can, of course, leave the car with a squeezed clutch pedal, but it can harm the release bearing, which will entail the need for repair.

First gear. On this gear, the car rises from the spot. Maximum overclocking speed on the 1st - 20 km / h. Also, the first speed is used when maneuvering in a small space, entering turns or when climbing a steep slide. You should remember, then the fuel consumption in the 1st transmission is extremely large, so do not be abused.

Second gear. This transmission is intermediate. Experienced drivers use the second transmission when maneuvering in traffic jams, descent from a slide or both transitional, between switching to other transmissions.

Third, fourth, fifth gear. These transmissions allow you to overclock the auto to the required speed mode. The higher the speed, the higher the transmission.

Reverse gear. How it becomes clear from the name, the appointment of this transfer parking, riding back, turning, parking.

Why learn to drive, standing on the manual transmission

Modern drivers boldly choose a car with an automatic box and lead a lot of arguments in its favor: from ease of control to economy and security. And there is logic in it. But, every experienced motorist will say that it is better to feel the car, respond to the situation and, simply feel the "real buzz" from the ride, will allow only MCPP.

Yes, I. driving lessons for beginners It is worth passing by car in which it standsmechanics . After all, the driver of the machine with a box-machine gets used to driving a car as a button, at the "On / Off" level. Reflexes and skills are lost, the ability of a timely response to the situation on the road is dulled.

Driving theory on a manual box

The theoretical base is very important for a beginner driver. After all, without theory, practice is impossible.

Passing the lessons driving a car on mechanics In a driving school, cadets necessarily explore the structure of the car. This knowledge must necessarily have every driver. He must understand how it works and how his car works to focus on its condition in the process of driving and understand what needs to be done in the event of a breakdown.

Skills driving for beginners on mechanics Purchased in practice lessons.

What is the clutch pedal?

Unlike cars with an automatic transmission, a clutch pedal is present in machines with MCPP. This is an important part of the car management and in many cases, at its work, one can judge the status of the car.

Passing the driving lessons for the car (mechanics) You will understand and feel her appointment. In short, the clutch pedal is a design element that takes part in the process of transmission of torque from the engine to wheels, and it allows you to briefly interrupt this transmission.

The clutch is needed to switch between the transmissions and the start of the machine from the place.

What is a "neutral"?

Often, beginners are not clear why neutral transmission is generally needed. As mentioned above, neutral transmission is used to ensure that the car remains in place. For example, if you need to move for a while, but there is no need to drown the engine.

The ratio of gear and speeds

Driving a machine with a manual transmissionAt first, it is difficult to have a newcomer. After all, it is first completely incomprehensible as and when switching transmissions and which transmission corresponds to a specific high-speed mode.

Proper driving on mechanics It assumes that the driver must navigate the sensations and sound of the engine in the shift shift. Also, you can use a tachometer and, depending on the number of revolutions, include a specific transmission.

Passing training by car where installedmanual Transmissionand acquiring skills and experience, you will stop thinking about when switching transmission and you will perform these manipulations "on the machine".

To help beginners, we give an indicative table of the ratio of gear and speeds.

Broadcast	mIN km / h	mAX km / h

How to start moving on the IPAT

Most newbies are more difficult to start from the scene. Often the clutch and gas pedals are squeezed not smoothly or incorrectly and the car begins to twitch and "coughing", nerve the instructor and scaring the driver.

Briefly tell you how to start on the manual transmission:

We start with what we turn on the "neutral".

Squeeze the clutch and bring the car.

Operate the clutch and turn on the first gear.

Smoothly release the clutch and follow the engine turnover. As soon as they see their drop, smoothly press the gas pedal.

After that, smoothly release the clutch and the car rows from the spot.

Tip: Do not make too sharp movements, the car can stumble. If this happened, do not despair and repeat all manipulations again.

How to switch transmission while driving

As we have said, switching transfers must be needed depending on the speed and power of the engine. This is the second most popular question among beginner drivers. We answer:

At the same time let go of the gas pedal and squeeze the clutch.

The car rides rolling and, at this time, you switch the speed.

How to stop

Now, let's talk about how to slow down and stop at the MCPP:

Gas gas smoothly and slowly.

Before stopping, squeeze the clutch.

Include neutral gear.

We let go of the pedals.

How to brake on mechanics

Lessons Driving on mechanics Be sure to provide such an important point of movement like braking. So, to brake on the manual mCP, you need:

Remove the leg with the gas pedal.

Then, squeeze the grip.

Lower the transfer and squeeze the clutch again.

First driving on mechanics The hardness is quite intense and, often, causes a considerable stress of beginners, but, under the supervision of our experienced instructors, you can ask all your questions and clarify the incomprehensible moments in place.

If you want to start riding and pass or choose any other, we invite you to our driving school "". Our people are located in almost every area of \u200b\u200bKiev. You can contact all the questions you are interested in the specified contact numbers, personally come to the nearest branch or use the feedback form on our website.

The car is the real need for any person. But the task of every motorist-novice is to carefully examine driving lessons for beginners, From this may depend on trafficAnd sometimes even the life and health of others.

Regardless of whether you visited a driving school or not when the car appears, it is necessary immediately "Refresh" the knowledge gained Or, otherwise, start learning from scratch. If you want to learn how to manage your "four-wheeled friend", and trading in a driving school was a few years ago - driving lessons for beginners will help you.

Before learning to drive a real car, you should familiarize yourself with the rules of the road. And not just read them, but also to learn. And after learning - follow. From this, not a very thick book will depend on your life.

So the lessons of driving for beginners should begin with the study of the rules. In that specialized textbooks will help you. Unlike dry rules, such textbooks make it possible to illustrate each rule by the road situation, visually show marking, sign and position of vehicles. Thanks to the illustrations, during the movement, you remember the correct actions.

Also there are good driving simulatorswhich are performed in the computer game format. They will be an excellent helper for those who want to quickly explore the rules and road signs.

For self-control, passing driving lessons for beginners can use Examing tickets. There are exams in a driving school. They can be purchased in print, as well as pass online. To whom what method is more convenient - decide on your own. Having answered right on all the tickets, you will not only secure your knowledge, and also qualitatively prepare for the "right" exam.

So, with the theory is finished. If you have never before driving a car - then to start you need to get used to it and stop being afraid. To do this, get along the driver's seat, turn the ignition and listen to the sound of the motor. Periodically try pressing the gas pedal.

It is necessary that you are accustomed to the sound of the motor, to how the car is gaining momentum.

How to learn to drive a car on mechanics from scratch to a woman?

Fifteen or twenty years ago, men feared for their lives, seeing the lady driving. Today, half of students in courses - girls who want to learn how to learn to drive a car on mechanics from scratch.

Firstly, choose this case the right clothes and shoes. Choose loose clothing, do not dress short and tight dresses and skirts. And also give up heels and thick platforms, at least driving. As an option - returned in the car for driving.

Today, most girls prefer an automatic transmission transmission, and a woman who owns the driving skill of a car "with mechanics", causes admiration and delight of those surrounding men. Therefore, if you plan to become "your boyfriend" on the road, do not be lazy and find out how to learn how to drive a car on mechanics from scratch.

After all, there is nothing complicated in the mechanics. It is just enough to get used to it. Well, on one pedal in the car will be more. Girls, be sure to read the next section. But different videos how to learn to drive a car from scratch on your own, studying all the azam and intricacies, you can see on this page.

Talk about security. Nature ordered in such a way that girls have much the instinct of self-preservation is largely developed. That is why they are trying to control the situation on the road while driving. Most girls driving are trying to drive a safe driving vehicle. But for men driving is rather a game and a way to obtain adrenaline.

How to touch the machine with a manual gearbox?

Before learning how to touch the machine with a manual gearbox and start moving, it is necessary to make the following actions.:

visual inspection - Check the condition of the wheels, are there any oils or fuel, if you plan to move in the evening - check the performance of headlights and dimensions.
adjustment - adjust the chair (the distance to the steering wheel, the tilt of the back), the side mirrors,
check security - fastening up seat belt.

Preparation Completed, it remains to be understood on a specific example, how to touch from a machine with a manual transmission. Even for dummies it is clear that, above all, it is necessary to "start" the car. Tighten the key to the ignition lock so that the engine earns. Hearing the characteristic sound of the engine work - release the key. Make sure the machine is not standing on the manual brake. Since we consider the question: how to touch from the machine with a manual transmission, the video instruction is located at the beginning of this section, will tell you more and colorfully, and the text will help to supplement these knowledge.

To start motion turn on the first transmission.
Click to Floor Pedal Clutch (The most left pedal) and translate the gear lever to the first transmission position.
After that, press the gas pedal (Extreme on the right side) so that the tachometer was an indicator in 2000 revolutions.
Very smoothly leaving the clutchAt the same time, keep the gas pedal and gradually add gas. So you went.

It is important to work with two legs At the same time parallel. If you release the grip sharply - the car jeshes and stalls. From practical recommendations on how to properly touched from a place on a manual transmission, we turn to the braking skill.

How to brake on the machine with a manual transmission?

Learning to start - this is good, but for a full-fledged ride you need to be able to stop. Yes not just stop, but slow down. Sometimes even sharply. No, of course, you can wait until the car will stop independently by passing the inertia.

However, what if you are an obstacle or traffic light? Here for this and came up with a brake pedal. She is in the middle. Press right foot. Want to avoid jerks and unpleasant situations? Press brake pedal smoothly (except cases of emergency braking). Therefore, novice drivers are very important to know how to brake on the machine with a manual transmission.

To begin with, try to reduce the speed of the car - remove the right leg with the gas pedal and press the brake pedal.
If it is necessary to complete the stop - the right foot is on the brake pedal, and the left is on the clutch.
The stronger to harvest the brake, the more the brake pads will put on the wheel and the car will stop faster.

It is important to remember that braking distances The car depends on several factors:

motor loading;
the presence of ice on the road;
dry or wet asphalt;
asphalt or dirt road;
tire status, etc.

Therefore, the brake pedal sometimes does not work. Do not panic. In this case in the car came up hand brake, the so-called "handbrake". This is a lever that is located a little behind the transmission lever. To use the handbrake as a brake, it is necessary to raise it up. Remember that this is not a replacement brake and in case of violation of the brake work, it is impossible to continue to repair.

On what revolutions correctly switch the transfer when driving?

So that the car remains longer on the go, as well as for the maximum efficient fuel consumption, it should be carefully referred to the gear shift process.

What revolutions switch the transfer?

Transfer switches when tachometer indicators at 2500 - 3000 revolutions. This is the most comfortable engine of the engine. So it will be the smallest fuel consumption.

If you purchased a car with manual transmission, but do not know how to switch properly, this material is intended for you. It should be started with the fact that training on mechanics is practically the same way that cycling ride.

What is good mechanics?

There are several advantages that has a car with manual transmission. Read them.

Such a box is an ideal means to control the vehicle.
Setting the pace of movement of the machine, you can accelerate to a higher speed.
Man driving such a car, makes several things at the same time than and proves his ability to this.
Riding on the mechanics provides the driver with valuable experience, and he, in turn, will come in handy in the future even when driving a machine gun.
In the machine equipped with automatic transmission, it is impossible to trim due to obvious reasons.
Thanks to mechanics significantly saved consumable fuel.
Manual box does not allow professional maneuvers.
Finally, automation is simply a "female" way of driving (according to many motorists).

With the benefits figured out, now find out how to ride mechanics.

Where to learn better?

For training it is necessary to choose a quiet and peaceful place in which there would be no other cars. It is desirable that it was a flat place without slopes - so your attempts to get used in the manual transmission will be easier. In short, there is nothing complicated here, so we go directly to learning.

How to learn to ride mechanics?

Initially, it is recommended to lower the glass - so you will better hear the sound of the engine. The rear view mirrors should be placed so that they are as comfortable to watch them. Prepared, you need to run away and act according to the algorithm below.

Gaza pedal is on the right side, the brakes - in the center, and the clutch, respectively, on the left. It's simple here, so we get to the next stage.

Pay attention to one curious moment: this location of pedals is inherent not only to the left-handed, but also right-hand vehicles.

Who does not know, the clutch pedal is intended to switch speeds. First you need to make sure that later you can squeeze this pedal until it stops. It is explained by the fact that the gear shift is possible only if the clutch is completely squeezed.
Adjust the seat. If necessary, adjust your seat in such a way as to be easily reached before clutch.
Practice with the clutch pedal. Next, you need to get acquainted with what exactly pressing this pedal differs from similar actions with others. To this end, they must be pressed for some time in order to get used to the location. With this clutch, squeeze only the left foot, and the brake with the gas is right! Let the clutch slowly several times until your foot get used to everything.

Turn on the neutral gear. To do this, select the average position of the speed switch lever (it should be located in the center). In order to determine whether a "neutral" was really included, it is necessary to simply pull this lever to the right and left. In the event that its movement is free, neutral transmission is considered to be enabled.
Get the engine by clicking on the clutch pedal. Many models of machines are characterized by the fact that the motor in them can be started exclusively with a squeezed clutch. Moreover, this is also a kind of safety measure - if the lever was accidentally left for some transmission, the clutch will prevent unintentional car jerk at the institution.

Note! When the engine is equipped, the clutch must be released smoothly. Then it should be verified that the lever is really on the "neutral".

Turn on the first gear. The next step is to repeated clutch and turn on the first gear. As a rule, it is located in the upper left corner, although its location is recommended to be clarified in advance. Also note that the location of all speeds is usually indicated on the arm of the lever in the form of a miniature scheme.
Train your clutch. You should start with smooth and slow release of the pedal before the start of the engine turns. Then the pedal is squeezed again, and the exercise is repeated so much so that you have learned to determine the moment when turns are started ( this is also called the "clutch moment").
Touch from the spot. To do this, you need to turn on the first transmission, after which you smoothly release the clutch - traditionally until the turning distance. At this point, we can slightly press the other foot on the gas, while the clutch needs to be saved. If this is done too slowly / fast, then the car is likely to stall. But there is nothing terrible in this - repeat the exercise until you learn more or less confidently to touch.

See how to touch the mechanics correctly:

Special attention should be paid to the fact that there is a front of the vehicle. If the training is held with the assistant, then he must sit on the side and be prepared if necessary to pull for the "handbrake". This moment is considered one of the most complicated, however, with due diligence, everything is sooner or later it will definitely be possible.

Second gear. After the start, you need to drive for a while on the first gear to get used to everything. Then, when the engine turnover exceeds 3 thousand, it is necessary to release the gas, parallel to squeezing the clutch. While the car moves rolling, you need to turn on the second speed, after which the clutch is completely released. Only after that you can accelerate further. The inclusion of all subsequent gears occurs in a similar way.
Move on the transfer. After turning on the transfer, you need to remove from the clutch. It is not necessary to keep it on the pedals constantly, otherwise the clutch mechanism is premature.
Brake. If you need to stop the leg from the gas you need to move to the brake pedal. Press the required effort. At a speed of 10-15 kilometers, the car will begin to shake a little - at this moment it is necessary to squeeze the clutch and turn on the "neutral".

When everything starts to get, you will notice with surprise that control mechanics is not so hard as many consider. Continue training, improve your skills to driving even more pleasure!

What to pay attention to?

And attention should be paid to the movement at the rear speed. If you are fine with the clutch, then to move the following steps.

Slit clutch, turn on the rear speed.
Look in the mirrors, determine the trajectory of the future movement.
Slowly lower the clutch until the machine starts moving. Next, do not let go - so the speed will be small.

If necessary, the slowdown must be pressed only more to the clutch pedal.

Outcome

Learning to ride the mechanics is easy. It will be better if there is an experienced driver next to you, which will help with the Council and physically. The main thing - learn to ride outside lively trails and strive for success.

Safety and comfort of your driving depends on landing. The back of the chair should have the right slope: not quite vertical, but also not laughing back. The position of the chair should be such that, with full pressing on the clutch pedal, your foot would have 120 degrees on bend, and the hands would be slightly bent on the steering wheel.

Work with pedals

Left leg: grip, right leg: brake and gas. Pressing the pedal should always be smooth. To switch gear, use the clutch pedal. For a set of velocity and braking, we use gas and brake pedals, respectively.

Passing of turns

The trajectory must be as smooth and viewed. Before turning, we reset the speed, go to the 2nd gear. When leaving the turn, press gas and occupy the desired trajectory.

Braking

First we remove the leg with the gas pedal and carry it on the brake pedal. We reduce speed. Then survive the clutch, go to the neutral gear and make the car to the complete stop. When braking, it is necessary to take into account the condition of the road surface, because The braking path depends on it.

Steering

Essay must be closed, because This allows you to fully control the safety of the car movement. When rotating the steering wheel, the hands should not be intertwined, movements should be smooth, but if necessary, fast.

Smooth stroke

Working clutch and gas pedals are needed smoothly. When moving from one transmission to another, it is necessary to take into account the engine speed and where it is necessary to add it. In such cases, the movement of the car will be smooth and pleasant.

Driving a car with a manual transmission occurs in compliance with a specific knob switching algorithm. Rod and jerking machines break the composite box elements.

Starting driving, read the theory, find out the principle of operation of mechanical gearboxes.

Transmission (MCPP) 2 destinations:

transferring torque of the power unit of the car to the wheels;
regulation of the volume of thrust in various conditions of movement.

Driving machines with mechanical boxes implies when switching gear speed loss by vehicle (movement occurs inertially). Switch the handle smoothly, without braking a car.
Manage MCPP is located in the cabin - the handle on the right side of the driver. The machine with mechanical mechanics begins at first gear, then switches to the second, then the driver is guided by the testimony of the tachometer, the sound of the motor or its own sensations and in the corresponding moment switches the box, providing speeds higher than the previous one.

The basis of the operation of the transmission implies the principle of changes in torque steps. Switching the handle in the cabin, begin to move gears. Steps are characterized by a certain speed of rotation. Ride on reduced transmission at high speed is fraught with breakboxes of mechanical boxes. Distinguish between four, five, six speed boxes.
The calculation of the dependence of the speed of machines with mechanics and the selected transmission is displayed in the table.

Using the specified parameters can be controlled by an unloaded car. In reality, the speed decreases depending on the concomitant factors.
The first gear is used to touch. The second-going under the slope and in traffic jams. The third is used in the city, and the rest are for country tracks.
With neutral gear, the torque torque is not transmitted wheels. The operating engine at neutral transmission and the gas pedal pressed in the static position of the machine.

Purpose and location of pedals:

Located on the left, squeeze into the floor (left foot), starting the movement of the machine and switching speeds.
Pedal in the midst brake. Press right foot.
The extreme right pedal gas functions depending on the clutch pedal: gas are pressed, releasing clutch pedal.

Advantages of MCPP:

little mass;
convenient repair and maintenance;
small cost of manufacture;
there is no cooling system;
endurance;
machine towing is possible;
smooth ride;
democratic fuel consumption;
chance to engage extreme driving;
in emergency situations, the car will start "from the pusher";

Cons MCPP:

chance to overload the motor and box;
it is impossible to gradually change the transfer relationship;
it is difficult to choose a transfer;
below comfort (than automatic transmission);
tedicing riding in the city traffic stream.

The manual box provides an adequate mode of operation of the motor under different driving conditions. Adjustment of the velocity by the manual method of switching steps.

Be sure to watch the video: how to trim with the manual transmission:

Driving Pose in Auto

"Teapots" are trying to sit in a car, strange ways: sit in the auto back and begin to unfold on the chair, taking a convenient position in order to control the car.
Go to the car, on the driver's side, open the vehicle door with your left hand and direct the right leg to the gas pedal, sit down, close the door tightly.
Adjust the driver's seat, consider:

The driver's seat back is located with a small slope (angle of inclination is approximate to 90 degrees).
The back adjacent to the back of the seating.
Feet do not get to the steering wheel.
The driver is watching in the mirrors of the rear view space behind and left from the car.

Adjust the driver's seat using the sitting mechanisms. Feet freely get to the pedals and bent in the knees. To adjust the seat when moving the machine is categorically prohibited. Incorrect seat exhibited - the voltage of the spine and the driver's elbow joints, plus a decrease in the concentration of attention. Driving place adjustment is made correctly: leaning against the back of the chair and switching the transmission remote from the driver, the driver does not feel discomfort.

Beginning driving

Driving a car with a manual transmission begins with the placement of speeds. So that during the movement of the vehicle, perform switching automatically, not to look after the switch lever. The initial stage of learning with the engine turned off is so safer.
Remember the location of the gear is consistently switched the box lever to different positions. The gear location scheme is applied to the lever. There is no diagram - consult with drivers, let them prompt the location of each transmission. The average position (the lever is freely moving) - neutral.

Having learned to switch the box handle, go to the next step: align the switching of speeds with pressing the clutch and gas pedals. Put the box of the box to the neutral position, having previously pushed the clutch, start the motor and warm up to the operating temperature. If the ambient temperature is below zero: warming up the engine is pressing on the clutch pedal. So accelerates oil heating in the box. Create a car when the transfer is turned off - so that the machine does not start moving uncontrollably.
Starting driving, smoothly release the clutch pedal and simultaneously press the gas pedal. So that the machine does not block the engine need to be rotated. Increase them by pressing gas (lightly), so as not to provoke a sharp start. Clutch pedal during speed switching Do not press longer than 2 seconds.
Learn to switch speed using a tachometer, or listen to the power unit. If the motor turns are small and the car does not dial the desired speed, then switch to the neutral position, then go to reduced gear.

If the motor turnover is very high, turn on higher gear. Tachometer readings will help to navigate the engine speed.
To learn to ride back, lighten your rear speed control. Include it can be stopped by a car. If the lever switch is incorrect, the transmission will pop up. At the rear velocity, the box is very quickly gaining momentum. Therefore, it is dangerous to ride it for a long time.

Brake in different situations

Stopping on the dry surface, do not switch the car with high gears to low, reduce speed on this transmission.
Drive cars in rainy weather and when ice is dangerous: the road surface becomes slippery. Therefore, when braking cars, you need to switch to reduced transmission to reset the speed. This will control the angle of the possible drift of the machine.
Would you like to learn how to slow down on a slippery road? : Stick instructions:

reset;
let go of the clutch;
switch to reduced gear;
squeeze the grip again.

The sequence of these actions leads to the "engine braking", allows you to avoid blocking the wheels from the machine.

Ducked car in the snow? - Take advantage of the "swinging" vehicle. To do this, make a move forward at the first speed, then turn on the rear speed and move backwards.

Technique stopping cars on the road having a bias. Put the machine on the handbrake, and turn on the neutral transmission, releasing the handbrake, switch to the first speed, squeeze the clutch and tried from the place, the release of the grip and at the same time smoothly pressing gas. There will be a moment when the car will stop moving back, in this position you can keep the car on a lift or hill without using a brake.
To leave the vehicle on the parking lot, stop the motor, click on the clutch pedal and turn on the first gear. This allows you to warn auto from rolling. You can use a manual brake. Returning to the car, be sure to switch the box lever to the neutral position.

For sharp braking on a dry road apply the scheme:

let go of the gas pedal;
press the clutch pedal;
push the brake to stop the car;
switched to neutral transmission and release pedals;
put a car on the handbrake.

The braking method of downshifting stops the car faster than the use of only brake pedals. To take advantage of this technique, apply the scheme:

squeeze the clutch pedal and switch to the third gear;
put the right leg on the brake pedal;
start smoothly remove the leg with clutch pedals;
before complete stopping, the clutch pedal is squeezed again;
do not use the first speed as less transmission.

Driving a car with a manual gearbox -Fromable process, heavier driving with automatic transmission. By purchasing certain skills and experience, the driver, having mastered the principle of operation of mechanical boxes, feels a car, he understands the connection between speeds and a box.

You can not ride on neutral transmission, when rolling the car from the slope, the wheels can occur and the loss of control over control. Insecure car driving on a slippery road.
Drinking to the traffic light, the engine, then turn on the reduced gear.
When controlling the machine, do not squeeze the clutch - it harms the release bearing, use the neutral position of the box lever.
In winter, do not leave the car on the handbrake: the brake pads are frozen and the car does not touch.
Moving a lying policeman, reduce the speed away from it, and before the obstacle herself sharply release the brake.
When the vehicle is moving with a stable speed, do not hold the left foot over the clutch pedal. This leads to overvoltage of the muscles and involuntary pressing on the grip, which is fraught with its breakdown.
Motor operation Unstable: Click on the clutch and wait until the engine starts to work correctly.
Squeeze the clutch to the floor before switching the transfer.
Knowing that it will be necessary to park the car on the slope, take a brick on the road, put it under the wheel of the machine and the car will not roll.
Before turning on the reverse gear, stop the vehicle.
Beginner drivers when switching speeds are focused on the tachometer. Driving auto needs to be given the possible motor breakage due to high engine speed.
Car stalled, you do not need to start it immediately. Movie the minute: the starter does not overheat and the battery will not discharge.

The rights are obtained, but there is no confidence in the right driving, select the roads unparalleled cars and work out in driving. You will get used to the car and feel confident.

Driving a car with mechanics requires patience and forces of a novice driver. Having confused on the road and expanding the car to the sideline, turn on the accident, calm down and continue the movement.

A beginner driver needs to ignore the Khamsky attitude of other drivers (ridicule and cutting cars marked with a student).
Entering the debate with Hamami while driving you risk becoming a member of an accident, after the incident will have to repair the body of your own car. Beginning driver behind the wheel of the car you need:

Be collected (missing panic);
Be polite in relation to other participants of the movement;
Listen to the operation of the motor;
Look at the tachometer;
Watch in the mirror.

It will take time and beginner will learn how to use the MCPP. Competent car management allows saving fuel, plus gives a chance to feel the power of the motor.