Do not seek goodness from good ... Or the model is so successful?
Another replica is a direct descendant of the Alarm of the Mongoose AMG700 Plus from 1998 - one of the most popular models of all times and peoples. The continuity is visible in everything - the keychain is almost the same, only another button was added. The rest is the case, the design of the instruction, the sensor - nothing has changed. Open the block. All skewed exemplary - Mongoose (more precisely, Taiwanese plant "Lighton") always famous high quality assembly. Mixed mixed - on the bottom side of the board there are components for surface mounting, on top - mounted installation. Obviously, they did not save on the quality of the parts - the varistor, the transistor on Sirena, the built-in lock relay - all this is taken with a fair reserve for power (and therefore in reliability). Processor Wpayan; The tracks to the relay are shown from the soul. All connectors are located on one side of the board; the main connector is a two-row sealed Molex-best option for car alarms. Built-in blocking - this can be said, brand ideology. It is really convenient for installers, it works reliable. But from an anti-theft point of view, this is not the best solution, especially when the wires to the blocking relay give themselves with their heads. The keychain is made of a very pleasant to the touch of plastic, with a slight rough surface. He lies in his hand as glove. Rubber buttons are pressed flawlessly - you do not have. Each button "lies" in a separate recess, so they are convenient to look at the touch, and it is randomly difficult to push it. In addition, the scheme has software protection from long-term pressing - after a few seconds, the parcels are stopped in the ether in order not to spend energy into the ether. The keychain is not so wonderful. No, everything is done great, only the LC chain is applied as a stabilizing circuit. This is an archaic solution, but rather cheap. The problem is that with intensive operation of the LC-contour may require adjustment after a few months. . And who will do it? On the Mongoose AMG770 instructions, the eye is resting. Do not say that this is a masterpiece, but the mangoskaya instruction does not force the instruction to strain and do something. It is clear from it that there is a passive immobilizer in the system (as in Excellent Plus), but it can be shutdown on any keychain button. 
It is curious that in the AMG770 there remained a completely unpopular function of protection against a robbery with a preventive mode of mode and triggering alarm on the fact of opening the door and inclusion of ignition. Here they are, traditions! This function at first glance is inconvenient, but only because the consumer does not find the desire to figure out. And spinning and simulateing a criminal situation, it is quite possible to take the rule to use "Anti-Haigek" every day. It is not so inconvenient, in the end. In addition, the engine is blocked in the algorithm in the "anti-hajek", imitating a malfunction. To non-standard in this class, we will take protection with a working engine, erasing the codes of all keychains, except for the input from the constituent of the central locking state and two service channels - programmable and on the pager or "Comfort", on the choice. And, of course, you need to mention About the famous "mangostess" card, representing instructions in miniature. On this reminder, the size of the credit card indicates all the basic operations in any abnormal situation.
pros: Magnificent keychain, great quality manufacturing, user memo, guarding engine, Entrance CZ
Minuses: Unice blocking, no surfactant stabilizer.
Verdict: A rare case when old, in fact, the alarm is better than most new ones.
Detail
Classic class
Average price $ 45
Points 5 (5)
Shock sensor: external, magnetoelectric
Lock relay: Built-in, N / s
Siren Included: Yes
Information:
Instruction
Alarm Mongoose AMG 770 is designed to protect the doors of the car, its hood and trunk, intra-alone space and space
in the immediate vicinity of your car. In addition, AMG 770 prevents unauthorized engine launch.
The functions listed above can be implemented to a greater or lesser extent, depending on the connected standard or additional
security Tools. Continuate with the installer !!!
To prevent unauthorized access to the Mongoose AMG 770 system, the radio command code is protected based on KeeloQTM coding technology, which has been successfully opposing the attempts to intercept codes using code 100, the built-in anti-scan function that prohibits the signaling of the alarm by the simple selection of random codes and the status memory function that does not allow to neutralize Mongoose AMG 770 simply removing and putting the terminal car batterySince in this case an alarm will turn on and the engine lock will be saved.
Interrupt and power recovery when the security is disabled, does not create alarm system so as not to create difficulties, for example, when repaired. If the power was disabled when the alarm was in Valet mode, then the subsequent feed will return the alarm to the same state.
In order to avoid locking the keys inside the car, when the power is restored from the car battery, there is no change in the state of door locks.
Avoid false alarms will allow the function of bypassing a faulty zone that will turn off faulty sensor Before the end of the security cycle, if it caused anxiety to turn on 10 times.
All other controlled zones and locks will remain enabled.
The programmable function of accounting for the maintenance delay makes it possible to use the Mongoose AMG 770 on any types of cars.
To increase the security properties of the system and ease of use, the Mongoose AMG 770 is equipped with additional channels with software selection options:
- to connect a pager or automatic closing of glasses at remote or automatic arming;
- To control the electrical lock of the trunk or other electrical device or to connect the Mongoose Communicator block, allowing you to control the Anti Hi-Jack function using an anti-discharge card.
Manual
Introduction
The Alarm of the Mongoose AMG 770 is designed to protect the doors of the car, its hood and trunk, intra-alone space and space in close proximity to your car. In addition, AMG 770 prevents unauthorized engine launch.
The functions listed above can be implemented to a greater or less depending on the connected standard or additional security tools.
Consult the installer.
To prevent unauthorized access to the system provided code Protection Radiocomand On the basis of Keeloq coding technology. Successfully opposing the attempts to intercept codes using a grabber code, built-in anti-tanning function. prohibiting the disabling alarm by the simple selection of random codes and memory memory function. Not allowing to neutralize the alarm-standing signaling simply removing and putting the automotive battery terminal, as the alarm will turn on and the engine lock will be saved.
Interrupt and power recovery when disabled security will not trigger alarm response so as not to create difficulties, for example, during repair.
If the power was disabled when the alarm was in Valet mode, then the subsequent feed will return the alarm to the same state.
In order to avoid locking the keys inside the car, when the power is restored from the car battery, there is no change in the state of door locks.
Avoid false alarms will allow the function bypass faulty zone. Which will turn off the faulty sensor until the end of the security cycle, if it caused the turning on the alarm 10 times.
All other controlled zones and locks will remain enabled.
The programmable function of accounting for the delay of the cabin light makes it possible to use AMG 770 on any types of cars.
To increase the security properties of the system and the convenience of using the AMG 770 car equipped with additional channels with software selection options:
- to connect a pager or automatic closing of glasses at remote or automatic arming;
- to control the electric lock of the trunk or other electrical device or to connect the Mongoose Communicator unit, which allows you to control the Anti Hi-Jack function using an anti-discharge card.
By purchasing the standard AMG 770 kit you get:
- Central control unit with full set for installation.
- A two-level impact sensor, which is capable of distinguishing the weak and strong blows on the car body, which allows the alarms to respond to them, or a short strap of sirens, or the inclusion of a complete alarm.
- Two remote control keyfobs.
- LED to indicate signaling modes, designed to install in a car.
- Button emergency shutdownThe place of installation of which in the car you should choose to choose with your installer, with such a calculation to ensure sufficient coverage of its location, on the one hand, and ease of use, on the other.
- Complete instructions for managing all AMG 770 modes.
If you want to increase the security properties of your alarm, we advise you to purchase an additional two-level volume sensor capable of registering any movement both inside the car and in close proximity to it. AMG 770 has a special input for connecting such a sensor.
Keychain remote control signaling.
It is a miniature radio transmitter feeding from 12 volt batteries (type 23 A), which is enough for about 1 years of operation. A significant reduction in reception range of the transmitter command system indicates the need to replace the battery. The key chain is the four control buttons and the indicator LED. When you click on any of the buttons, the transmitter generates and transmits a special coded command, which changes with each new click on the buttons, thus preventing the possibility of intercepting the code of your signaling code-grabber.
Team table
The necessary information
PIN code.
To increase the secrecy of the alarm management in AMG 770, it is possible to use a personal code (PIN code) to emergency shutdown alarm, log in to the programming mode of additional keyfobs and user functions, disconnecting the anti-dimensional and hi-jack.
PIN Code may consist of one or two digits and to have a value or from 1 to 9, or from 11 to 99, depending on the software installation. In the manufacture of the system, the code is recorded in it equal to 1, however, we recommend that you specify a different value of the PIN code after installing the system (how to do it, read in the programming section). This will allow you to protect your security system from unauthorized removal from security.
To enter the PIN code, use the emergency shutdown button and the ignition key.
Alarm emergency disabling.
If the alarm keychain is missing or defective to remove the system from security, you must: open the door with the key, and the alarm mode will turn on, sit in the car, turn on the ignition and leave it in the position.
If you installed a unique PIN code - press the emergency shutdown button. The number of times equal to the specified PIN code value and turn off the ignition. If the code is entered correctly, the system will remove with protection.
If a two-digit code is installed, then entering the first digit as described above, turn on the ignition again and also enter the second, then turn off the ignition. If the code is entered correctly, the system will remove with protection.
TERMS OF USE
Management of main security modes
Argument.
To set the alarm to guard, when the ignition is turned off, press the 1 key fob button, if all the doors, the hood and trunk are closed, the siren will give one beep, and the lanterns will flash once. The LED system will begin to flash slowly, the door locks will close (if the car is equipped with lock lock drives). If any of the doors, the hood or trunk will be unlocked, three additional sound signals will follow and the lanterns will flash three times.
Security.
In the protection mode, the alarm controls the state of all existing door switches, the hood, trunk, turning on the ignition and the state of the shock sensor, as well, if you are additionally installed, the sensor volume, etc. In addition, the engine is blocked in the protection mode. If any of the protection zones is violated, 30 second alarms are turned on.
Anxiety.
If the alarm mode is turned on, then the siren will sound, and the signal lights flash for 30 seconds or before turning off their key fob button.
When the warning zone is triggered by the impact sensor or the external zone of the additional sensor, a short trill of the sirens will sound.
Removal.
To remove the alarm with the protection, you need to press the 1 key fob button, the siren will give 3 sound signals, and the signal lights blink twice. The LED will go out, door locks will open (if the car is equipped with locks lock drives). If the alarm mode turned on during the protection period, then four additional beeps follow when removing protection.
Panic.
If when the ignition is turned off and hold for 3 seconds. Button 1 will turn on the siren and signal lights. Pressing button 1 disables the mode. The inclusion and subsequent shutdown of panic does not change the status of the system, that is, it will remain in the protection, if it was in this mode, the doors, while remain locked, if the protection mode was disconnected and the door locks are open, arming and locking the doors will not happen .
Quiet production and quiet removal from security.
When you need to put or remove the alarm with protection without sound confirmation, so as not to disturb the surrounding sirens with the sounds, press the button 2. The execution of commands in this case will be confirmed only by light signals. The rest of the modes are completely similar to the formulation and removal with sound confirmation. With a quiet arming, the sound warning about the unlocked doors, the hood and trunk is preserved, so there is no danger that you will leave your car unlocked.
Arming with disconnected sensors.
If when arming, there is a need to turn off the salon sensors, for example, in the case when passengers or animals are required in the car, press the button 3.
For protection with disabled sensors without audio confirmation, press the button 4.
Security with the engine.
In order to put a car to protect the engine under the engine (for example, when heated), before pressing the button 1, press the 3 key fob button, then the protection mode with disabled sensors is activated, and the engine lock will not be turned on. To disable the security, you must click either the same combination of buttons or the 1 or 2. button In addition, if the protection was not disabled for 10 minutes or the ignition was turned off, the engine lock automatically turns on, but without re-locking the doors.
NOTE: To avoid the erroneous switching on the mode while the car moves, it is allowed to activate the system only for 10 seconds after opening and closing the door when the ignition is turned on, after these 10 seconds, the mode is prohibited from the expiration mode.
Use additional security features
Automatic reset (protection against accidental press).
If for 30 seconds. After removal from the protection, neither one of the doors, the hood or trunk was not opened, and the ignition was not included, the system will automatically return to the protection mode.
Two-step removal of protection.
If an alarm has been turned on, then by pressing the 1 button once, you only turn off the siren and signal lights (if the cause of the alarm is eliminated, i.e. for example, an open door or a shock sensor has stopped working). If the reason that caused the alarm is saved, it takes a re-pressing on the button. To complete the security, click the button again after turning off the alarm.
Auto Present.
The function can be turned on or disabled with programming.
If the function is enabled, then after turning off the ignition, opening and closing the door, the signal lights will flash twice, the LED will flash quickly. If within 30 seconds after that, all the doors, as well as the hood and the trunk will remain closed, the alarm will rise to protection, without locking the doors.
Automatic locking of doors when the ignition is turned on.
After 5 seconds, after switching on the ignition, the electrical locks of the doors are automatically locked, when the ignition is turned off, the locks are unlucky immediately. If any of the doors are open during these 5 seconds, the automatic locking will not occur to avoid locking the keys inside the car. The function can be disabled during installation.
Remote control of the central lock.
When the ignition is turned on, the car door locks can be locked at any time or by pressing the key chain 1 or 2, respectively.
Passive immobilizer mode.
The mode turns on and off programming.
If the mode is programmatically enabled, then after 1 minute after opening the door, the engine lock turns on when the ignition is turned off. No other protection zones in this case will be activated, doors locks are not locked.
When you turn on the ignition for a minute after opening the door, the mode activation is canceled until the door is open again when the ignition is turned off.
Immobilizer mode will also automatically turn on if the ignition is turned off all the doors remain closed for 10 minutes.
To turn off the immobilizer, press when the ignition is on, one of the four keyfob buttons. What exactly is selected by programming. Factory setting - button 1.
If for any reason you cannot use the keychain to turn off the immobilizer, enter the PIN code, as well as when crashing.
If when you try to disable the immobilizer, the wrong button is pressed, which is programmed to turn off, immediately turns on the alarm, disconnect which in the following ways:
- Press the desired keychain button.
- Enter PIN code.
- Turn off the ignition, put and remove the alarm with protection.
In the first and second case, an alarm and engine lock will be disconnected simultaneously. In the third case, the alarm will turn off, but the engine lock will be preserved before pressing right buttons or entering the correct PIN code.
By turning on the programmatically mode of the immobilizer, remember that:
- when the ignition is turned on and the immobilizer standing on the protection, the system will not perform any key chain commands before removing the immobilizer with protection;
- if the immobilizer mode has already been activated when exposing an alarm system, then after removing the engine lock, press the key fob button that turns off the immobilizer, or enter the PIN code.
Anti-Hi-Jack. Protection against robbery.
Your security system is equipped with a special anti-absorbing feature of Anti Hi-Jack, which will be automatically activated when the ignition is turned on, as well as in the case of opening any door when the ignition is turned on. Both modes can be turned on and off programming independently of each other.
If the function is programmatically enabled and you need to give the keys and leave the car, simply fulfill the requirements of robbers, Anti Hi-Jack will turn on the alarm and make robbers stop.
In order for the activation of Anti Hi-Jack to be a hindrance to the movement of the car and you had the opportunity to calmly disable it, as well as not to create a dangerous situation on the road, regardless of the activation method, the anti-theft procedure passes the following steps until the full Engine alarms and blocking:
- 30-second pause for entering the disconnect code After turning on the ignition or opening the door when the ignition is turned on. The system LED blinks slowly, reminding that you need to enter a disabling code.
- Warning mode. If you have not entered the disabling code during a 30 second pause, over the next 30 seconds the system will remind you of the short sound signals and flashing the signal lamps, the LED, while it will flash quickly.
- Alarm mode. At the end of the steps 1 and 2, if the disconnect code was never entered, the system switches to the alarm mode: complete sound and light alarms are turned on. With software inclusion lock mode with malfunction imitation, It will turn on simultaneously with the inclusion of anxiety. In this case, the engine lock will be carried out according to the following scheme: 1 second - blocking \u003d\u003e 5 seconds - pause \u003d\u003e 1 second - blocking \u003d\u003e 3 seconds - pause \u003d\u003e 1 second - blocking \u003d\u003e 2 seconds pause \u003d\u003e 1 second-block \u003d\u003e 2 seconds - pause, etc. The last cycle will be repeated until the ignition is turned off, after which the engine will be finally blocked and it will not be able to start it until the Anti Hi-Jack is completely disconnected. If the blocking with the fault simulation is disabled, the engine will be blocked immediately after turning off the ignition. The alarm mode continues until the ignition is turned off and will not remain in the off position for 60 seconds. Entering the disconnect code in the alarm mode is blocked. If the wrong code was entered twice for 1 or 2 stages, the system immediately goes into an alarm mode, without waiting for the end of the stage. At the end of the alarm mode, the system switches to blocking mode.
- Lock mode: 3 minutes. In this mode, the sound alarm is disabled, however, the light alarm and lock are saved, the input of the disconnect code is blocked, the LED does not burn. After 3 minutes, the light alarm is turned off, but all locks are saved, the system switches to the code standby mode.
- Code standby mode. Duration of the regime 30 seconds. Turn on the ignition, the LED will flash double flashes, enter the code. If the code is not entered or entered within 30 seconds, the system returns to the alarm 3 and the entire cycle is repeated.
Turning off Anti-Hi-Jack:
- For 30 second pause 1, as well as during a warning mode 2, ANTI-HI-JACK can be turned off by entering the lower discharge of the emergency shutdown code. To do this, you can use the keychain or the emergency shutdown button. When using the keychain it is necessary:
- when the ignition is on (the system LED slowly flashes with single flashes) Press and hold the 3 key fob button for three seconds;
- press the 2 key fob button. Number times equal to the value of the lower discharge of the emergency shutdown code. When using a button, press it when the ignition is turned on the number equal to the value of the junior discharge code.
If the code is entered correctly, after 5 seconds, the anti-hi-jack will turn off, the system will switch to normal operation, confirming this by a double audio and light signal; If the code is incorrect, you can repeat the input one more time.
- include ignition (the system LED will flash double flashes) Press and hold the 3 key fob button for three seconds;
- the LED system will flash quickly;
- press the 1 key fob button. Number times equal to the value of the senior discharge of the emergency shutdown code, press the 2 key fob button. Number times equal to the value of the lower discharge of the emergency shutdown code;
- if the code is entered correctly, after 5 seconds, anti-hi-jack will turn off, the system will switch to normal operation, confirming this by a double audio and light signal; In the case of incorpor code input, the system switches to alarm mode 3.
If you additionally installed the Mongoose Communicator module and programmatically turned on the anti-discharge card feature, the activation of Anti-Hi-Jack will be prohibited if there is a card inside the car for 2 minutes after turning on the ignition or opening the door when the ignition is turned on. If you need to turn off the ignition before the expiration of these 2 minutes, then you first turn off the Anti-Hi-Jack button to the emergency disconnect younger discharge of your PIN code.
In order to activate Anti-Hi-Jack, it is possible, besides the program inclusion of the function, be sure to install a two-digit disabling code for the system.
If you are simultaneously using an anti-hi-jack and a passive immobilizer mode, then after turning on the ignition, you must first turn off the immobilizer, and then enter the code to disable Anti-Hi-Jack.
ATTENTION! If the Anti-Hi-Jack anti-theft procedure is activated, the system executing any remote control commands, except for entering a personal shutting down code and a passive immobilizer shutdown command, are blocked.
Temporary Disconnection Modes Anti-Hi-Jack
- If, after disconnecting the anti-theft procedure, entering the emergency shutdown code (complete or lower discharge), none of the doors of the car opened, the ignition can be turned on and off the unlimited number of times, anti-hi-jack, and it will not be activated. At the first opening door mode, the mode is turned off.
- If to disable the anti-theft procedure, enter the disconnect code from the key fob open doorThe activation of Anti-Hi-Jack when opening the door will be canceled until it turns off and on the ignition.
You can also use the Valet mode to temporarily prevent the activation of Anti-Hi-Jack.
Diagnostic functions
Fault warning.
If, when arming, any door, the hood or trunk will be unlocked, you will hear 3 additional sound signals instead of one and lanterns flash 3 times.
Alarm memory.
In case of inclusion of anxiety during the period of protection, when removing from security, you will hear four sound signals instead of two and lights will also flash four times. Three series of outbreaks of the LED after turning on the ignition, the system will report a reason for the cause of the alarm:
Number of outbreaks in the series
Special service modes
Accounting for the delay of the cabin light.
The mode is activated by programming.
If the car has the function of the delay of the cabin light, and the main light delay is programmatically enabled, the door terminals will be taken under protection only after the light goes out in the cabin. Notification of non-closed doors when arming in this mode is absent.
Search for a car.
If during the period when the alarm is on guard or is in Valet mode for 3 seconds. Press the 2 button, the siren will publish one beep, and the lanterns will flash six times, designating the place of the car in the parking lot.
Valet mode.
In this mode, all system security functions are disabled. You can enable it, for example, when you give a car to the service, and then you do not have to leave the key chain of your alarm. This is an absolute guarantee from unauthorized recording of new keyfobs in memory of your security system.
To turn on the mode, it is necessary when the protection is disabled and the ignition is turned on by 3 seconds. Press the 4 key fob button, the signal lights flashlight three times, the system LED will light up in constant mode. In Valet mode, the possibility of remote control of the central locking and additional channels is preserved. Pressing the button 4 when the ignition is turned on, returns the system into normal operation mode, which it reports three sound signals.
Programming chains.
- Enable ignition.
- Enter the first (or only one) digit of your PIN code by pressing the emergency shutdown button appropriate.
- Turn on the ignition again. If a 2-digit PIN is installed, enter the second digit to the alarm button.
- Having finished entering the code, turn off and on the ignition again. If the code is entered correctly, the system is double sound signal Reports the entrance to the programming mode of the chains.
- Press the 1 programmable keyfob button. A short beep will confirm the key fob code in the memory of the system.
- To exit brass programming mode, turn off the ignition and press the emergency shutdown button or wait 15 seconds. About the output from the mode system will report by a double beep.
Programming functions.
In order to change the PIN value, erase from the memory of the system unnecessary to you key chains, enable or disable Anti Hi-Jack, set the new value of programmable functions, you must first perform the programming of the keyfobs described above, and for this you can use the keychain that is already known System. Then execute the following procedure:
- After completing the programming of the keyfobs, turn on the ignition.
- Enter the first digit number of the program switch, for which press the emergency shutdown button the number of times equal to this figure.
- Turn off, turn on the ignition and enter the alarm button to the second digit of the program switch number.
- To turn on the function, press the 1 key fob button for shutdown - button 2.
- If you need to change the value of other functions, turn off and turn on the ignition no later than 10 seconds and repeat the procedure starting from step 2. When the programming is completed, turn off the ignition and press the emergency shutdown button, the system of the double beep confirms the output from the mode.
When installing automotive alarms, it is important that the system ensures the preservation of not only the car, but also its owner.
Such important qualities have protective systems from Mongoose, a long time of pleasing users with high quality and wide functionality.
ATTENTION! Found a completely simple way to reduce fuel consumption! Do not believe? Auto mechanic with 15 years old also did not believe, until he tried. And now it saves 35,000 rubles per year in gasoline!
Mongoose is gradually becoming a manufacturer of a wide range of security systems. And now she introduced car alarm mongoose AMG. 700, which almost instantly became very popular among car owners.
In the first place this system put 2 factors: high specifications and affordable pricing policy. The breakdown from the Mongoose AMG 700 Super model will rarely happen, which makes the number of positive feedback from motorists even more.
What interesting features and modes can provide AMG 700 system:
- the mode in which the system operation occurs with minimal noise;
- alarm mode does not use Sirena, but only elements of illumination and user pager;
- the Anti-Hi-Jack function, which sequentially disables all the main assemblies of the unit, preventing the car hijacking;
- even when the system is disconnected, the car doors remain closed;
- when an incorrect command arrives, the system automatically goes into an alarm mode.
The AMG line does not stand still and the new Mongoose AMG 750 model is already installed on many cars. The system is more worked out, there are several interesting additions (for example, more stylish and modern design).
Mongoose makes the main bias on quality, while not raising the price to heaven. The cost of AMG 750 is not very different from previous model. The manufacturer does everything possible so that the user is familiar with the functionality of this alarm as a short time. A reliable confirmation of this fact is the understandable and simple instruction on the installation of car alarm, which comes complete with the security system.
- installed antigramberber, which prevents the key chain from scanning code;
- with the help of a special PIN code, with an emergency, you can disable the system;
- mode "Panic" will allow you to quickly get rid of unnecessary attention.
Technologies are developing very quickly, this confirms the Mongoose AMG 770 security system, the functionality of which has become more productive. There were several new products that deserve the attention of motorists, the device interface also became more convenient.
For this car alarm, unscrew changes of weather conditions are not terrible - the system continues to function at a high technical level.
The developers extended the service life of the device by making it immune to the ambient temperature. In addition to the operating instructions, the set includes a setup, so each user may try a chance in self-installation of the system.
- with the engine running, the security system continues to function;
- the system automatically warns the user about the invasion of the car;
- in addition to recording alarm, the system also conducts individual diagnostics.
Mongoose AMG 800.
Mongoose is gradually approaching a high-tech ideal. Mongoose AMG 800 car alarm also received key chains with a new, ergonomic design, which is why they are very comfortable lie in the hand. Changes touched and technical: the system independently controls many functions of the car and minimizes the user's work. The right is considered one of the best security systems both in Russia and abroad.
- the useful feature that turns off the operation of the system at a small time interval;
- the system independently bypass the failed area and continues to function properly;
- all the necessary information is displayed on the pager screen.
Mongoose AMG 850 is a technologically accurate and durable car security system. At the same time, the alarm has a smaller cost than earlier models.
The AMG 850 system for a long period of time occupies leading places in the market.
The operation of the system is as accurate as possible, there is all the necessary functionality. Car alarm not only will protect the car, but also will retain the life and health of the owner.
- the activation of the security mode occurs almost silently;
- alarm warns the car owner on the emergence of a malfunction;
- it is possible to program the duration of the response of the central locking and windows;
- in the installation provided additional relay blocking;
- simple connection scheme.
