Single-stage membrane regulator-pressure stabilizer Gas A6 direct action Used in industrial gas regulatory points (GP), as well as in the GP used in public and residential buildings. The unit is designed to reduce the pressure level to the desired level at the output. It complies with the requirement of the Pressure Equipment Directive, 97/23 / CE. Applied in working with gas fuel GOST 5542.
Installation scheme A6.
The gas pressure stabilizer can be mounted in any horizontal or vertical position, devoid of mounting stresses. With its work, it does not need additional maintenance, except for an external visual inspection and periodic cleaning of its surface.
Output pressure - see marking inscription
Option: Output pressure is adjustable.
Safety: Gas pressure stabilizer has reliable protective elementsthat B. automatic mode Stop the flow of liquefied gas when:
- the level of pressure in the input or outlet nozzles is reduced,
- too much increase in the level of gas pressure while restricting its selection,
- too much increase in pressure, the growth of which caused a stabilizer breakdown.
When organizing gas supply to consumers without the use of stabilizers, it is possible for only a limited number of gas consumers with different gas supply conditions; It is possible an unstable gas pressure with differentials, growth and reduction of the supply gas supply; There may be only a small distance from the reduced pressure of the SCP (GPP); Reducing the efficiency of household gas equipment and its efficiency; gas loss; It is impossible to apply a wide range of models and gas equipment manufacturers; You can not use equipment with automatic systems and a high efficiency, no prospects for the development of gas fuel consumers.
Advantages of applying gas pressure stabilizers during distribution:
- Establishing a stable level of gas pressure and feeding it in constant volume;
- The ability to organize any number of gas consumers with unchanged feed parameters;
- Minimum gas loss;
- Household gas equipment works with the highest efficiency and efficiency ratios;
- The ability to apply gas equipment in household conditions of the widest range and from different manufacturers.
- It is possible to use equipment with automatic systems and a high level of efficiency.
Regulators - pressure stabilizers correspond to that by 200020142.030-2013.
Pressure stabilizers are designed to reduce and maintain the output pressure in the object regulated in the specified limits, regardless of the pressure fluctuations at the input and flow changes.
Scope of pressure regulators - gas regulators and installations, gas burners and similar purpose instruments.
Climatic execution: y3.1 (-30 ... + 40 ° C); U2 (-40 ... + 40 ° C).
By type of accession to the pipeline, pressure stabilizers are manufactured:
- coupling from DN 15 to DN 50;
- flanges from DN 32 to DN 100.
The flanges of pressure stabilizers regulators correspond to GOST 12815, IP. 1, up to 0.6 MPa.
Material of the body of pressure-stabilizers aluminum alloys AK12EK, AK12PH.
General specifications Pressure Stabilizers Regulators
Maximum input pressure:
- for PC ... 0.5 - ... - 0.5 bar (500 mbar);
- for PC ... 6 - ... - 6 bar (6000 mbar).
The outlet pressure range is determined by the spring installed in the regulator
Maximum output pressure deviation: ± 10%
The temperature of the work environment - from minus 30 ° C to plus 70 ° C
The average service life is at least 9 years.
The installation of pressure stabilizers regulators is possible both on horizontal and vertical pipelines. 
1. Designation Series
2. Connecting size, inches
3. Maximum operating pressure:
- 0.5 - 0.5 bar;
- 6 - 6 bar
4. Range of regulation of output pressure(Lower limit - upper limit):
For regulators on the inlet pressure up to 0.5 bar:
- 2.5 - 9: 2.5 - 9 mbar;
- 5 - 13: 5 - 13 mbar;
- 5 - 20: 5 - 20 mbar;
- 10 - 30: 10 - 30 mbar;
- 25 - 55: 25 - 55 mbar;
- 30 - 70: 30 - 70 mbar;
- 60 - 110: 60 - 110 mbar;
- 100 - 150: 100 - 150 mbar;
- 140 - 200: 140 - 200 mbar.
For regulators for inlet pressure up to 6 bar:
5. C - the presence of a built-in safety-reset valve
6. Safety-reset valve triggering range(Lower limit - upper limit)
7. Climatic execution:
- Y3.1 (-30 ... + 40 ° С);
- U2 (-40 ... + 40 ° C).
8. Technical Condition Number: TU BY 200020142.030-2013.
Online application
We guarantee that your data will not be transferred to third parties under any circumstances.
The car GAZ-24 "Volga", is still popular among Russian motorists, is famous for the front suspension of an unusual design, thanks to which the car has received its smoothness. About the suspension of GAZ-24 and GAZ-24-10, its device, features of work and maintenance Read in this article.
Four threaded bushings on the rack (that is, on each sleeve of the upper and lower levers), as well as in the places of installation of a kkworn (two pieces). Adding oil is necessary until it starts flowing through the sealing rings of the sleeves. To prevent leakage and clogging, press oils are closed with caps, which are not losing when performing it. It is also necessary to pay attention to all suspension connections and the state of its details. Periodically, it is necessary to inspect the kingnery - it is due to the effects of high loads prone to wear and over time needs to be replaced. Finally, it is necessary to adjust the geometry of the chassis, that is, the installation of collapse and convergence. This should be done at a hundred when there are signs of inclusion - the appearance of uneven wear of rubber, with the "UGHO" of the car to the side, with a difficult return of the steering wheel in a neutral position, etc. Regular maintenance
