Currently, the price of protective 3D glass for iPhone 6 is in the range from 900 to 2500 rubles. Most stores for an additional fee (usually 30-40% of the cost of the goods) offer their services for gluing the accessory, but even they do not always manage to do it efficiently, which is why the right decision in such a situation would be to install the protective glass on their own.
If you are confident in your skills and knowledge, but doubt the correctness of the chosen solution, we have specially developed an instruction for you to install a protective 3D glass on a smartphone, which consists of 6 steps. The instruction is suitable for protective glasses on iPhone 6 6Swhich you can buy from our online store.
Wipe the screen with an alcohol wipe to remove fingerprints, dust, and dirt from the surface of your smartphone. Then use a dry microfiber cloth to remove any wet cleaning agent particles.
Use a large blue tape to remove invisible dust, hair, and crumbs. Peel off and stick on the absorber one by one. After completing the cleaning of the screen in Step 1-2, carefully inspect the smartphone display, you may have missed something. If so, we recommend that you repeat Step 1-2 until the surface is perfectly clean.
Take safety glass in your hands holding the edges, then gently peel off the pre-set black strip by pulling down on the sticker.
Bring the glass to the gadget at a distance of 1-2 mm, align the holes with the smartphone. Then slowly place it on the display. This step should be given special attention, as this is where most newbies get it wrong. You shouldn't rush here.
Press lightly with your index finger in the center of the 3D glass for iPhone 6. After pressing, the process of gluing the glass will automatically start, which is quite fast. Attention: after the glass has pressed its entire surface against the smartphone screen, you must not press on its edges until you remove the air bubbles.
Removing air from under the protective glass, which is not glued along the edge. Use a yellow microfiber cloth to squeeze out any air bubbles. Your movements should start from the center of the display and end at the 3D edge of the glass. Once the air has been removed, press the 3D edges of the glass to complete the bonding process.
Tips and Notes:
The quality of gluing depends on many factors: experience, knowledge, shaking hands, etc. If, as a result, the holes of the protective glass do not match with smartphones, we advise you to make the adjustment in the following steps.
Problem 1
Most of the adhesive layer is located not only on the protective glass itself, but also on its 3D edges. If after the completion of the process of gluing the protective glass, it keeps on a kind word, this means only one thing, you did not stick it exactly.
Solution to problem 1
Peel the accessory away from the display, carefully align the holes with the smartphone and repeat Steps 4-6.
Problem 2
Small air bubbles appear after the glass is installed.
Probably, you did not perform the glass gluing process according to the algorithm specified in Step 5. You applied force not to the center of the screen, but to its 3D edge.
Solution to problem 2
Try to remove air particles by expelling them from the center of the screen to its edge, if such actions do not lead to the desired result, peel off the protective glass and install it in accordance with Step 5-6.
Do I need to glue the protective glass on the iPhone 6? It is worth deciding on the purpose of such an accessory. If you often drop your phone or use it in aggressive conditions, where any mechanical force can leave scratches or chips on the display, the protective glass will minimize damage to the smartphone screen. If you handle your phone with care, then the need to use tempered glass fades into the background.
If you still have questions about how to properly stick a protective glass on a smartphone, we will be happy to answer them in the comments. As a rule, beginners often make a large number of mistakes due to which the protective glass on the iphone 6 peels off. Carefully read our instructions so that the glass will serve you for a long time.
Details Online store blog Created: 16 July 2016The modern market offers each buyer a huge amount different models gadgets, smartphones and other similar devices. Despite the fact that the display is made reliably, the buyer decides to extend its life by purchasing a protective glass. This is due to the fact that after a while we do not treat smartphones as carefully as in the first stage. Today we will talk about how to clean the protective glass with inside and what means we need for this.
What is safety glass?
Protective glass is a modern type of display coating on smartphones and gadgets. They make it using chemical method based on tempered glass.
Important! Compared to ordinary film, it is several times thicker and harder. That is why, if the phone has this coating, it protects the screen from fingerprints, scratches, moisture and even shock. Despite these specifications, brightness and color do not change.
Due to the multilayer coating, the glass thickness varies from 0.25 mm to 0.5 mm, the composition of which is as follows:
- The first layer is always silicone based. It sticks to the display.
- The next layer is bonding. It is he who does not allow the fragments to spread if a crack or mechanical shock occurs.
- The third coating layer is an anti-reflective film. It maintains the visibility of drawings on the screen when exposed to direct sunlight or other bright light.
- The protective layer protects against shocks, falls and other mechanical damage.
- The very last layer is the oleophobic coating. It protects against moisture, fingerprints and makes it easy to clean.
With heavy use, the top coat, which ensures the reliability of the unit, becomes dirty. It is then that the question arises of how to clean the protective glass of the phone. How to do this and what is required for this, we will consider further.
What is screen protector?
The protective film has appeared on smartphones for a long time. It is not a high-tech product and is present on every gadget. This product is characterized by the presence of three layers:
- the lower one sticks to the screen;
- medium absorbs ultraviolet radiation and provides brightness when exposed to bright light;
- upper - is responsible for protecting the display screen.
Important! The most important thing for the film is proper adhesion. To do this, you need to have a little skill, since the first time it can not always work.
All protective films that are present on the market for smartphones and gadgets are divided into three types: matte, glossy and mirror. Let's take a closer look at each view in order to understand if there will be a difference in cleaning:
- The matte film absorbs glare and also hides fingerprints. The main disadvantage is that it degrades image quality. However, its cost is very low. Many masters consider such a film to be technological and advise not to stop the final choice on this product.
- The glossy screen protector is the most popular among similar products. The main disadvantage of such a coating is that it can be easily damaged. The film strongly reflects light, scratches and other quickly appear on it mechanical damage... Fingerprints are also visible.
- Mirror film is the least popular among similar products. The peculiarity is that when the screen is off, it can mirror the image. However, the quality and brightness of the screen changes when this coating is applied - this is the main disadvantage.
All of the above films become dirty and this is especially noticeable when dust gets under the coatings. We will now analyze how to clean the film for the phone.
How do I clean the protective glass on my phone?
If you are thinking about how to clean the film for your phone, then ordinary scotch tape, or as it is also called, adhesive tape, will help you. To do this, you need:
- take a wide tape;
- cut off a piece of about 30-40 cm from it;
- glue it to the surface so that the sticky side is on top.
After that it costs protective film stick to the adhesive tape. Then very carefully and slowly peel off the film immediately. All the dust that was present on this product will go away and the sticky layer will remain.
Important! If you need to remove scratches from the upper part of the protection, then polish the defects with felt, a soft cloth or with the help of auxiliary means - white toothpaste, GOI paste or olive oil.
Another way to clean the inside of the safety glass is to use soap and water. For this:
- You need to remove the contaminated product from the phone.
- In hot water, wash off all dust particles.
- After carrying out this procedure, it is worth very well to lather the sticky layer with soap. For this, it is better to use two or three layers.
- Then take and wash off the soapy water under water. See that the water is glass from the film.
- Then we glue the film onto the cleaned, damp display using an ordinary credit card.
- We make sure that no air bubbles and other lint get in.
Today we have taken apart all types of protective films and talked about how to clean the protective glass from the inside. As you can see, this is very easy to do. Now you do not need to throw out the old film and stick a new one, because you can simply peel and re-stick the same protection on the gadget. Use our tips and make your life easier!
Many people buy themselves smartphones of new models, not only in order to use all modern features such gadgets, but also to emphasize their status. And what style can we talk about if the screen is scratched or cracked altogether. In order to prevent such possible troubles, almost every phone user uses a screen protector. Bubbles are caused by air trapped under the surface of a useful accessory such as a film. It so happens that a "defect" is formed due to a small speck of dust, then the process becomes a little more complicated - you will have to change the entire film. In order to first or re-stick the film on your smartphone, you need to know how to remove bubbles from the phone film, because this is perhaps the only and main nuance in this matter. Today we will tell you more about this and try to get around all the obstacles.
Film replacement
This procedure requires extreme care and a high level of cleanliness in the room. It is best to carry out all manipulations in the bathroom, because dust does not fly in the air due to humidity. The following is to be done:
- We take a smartphone in our hands and smooth out the air bubbles with our fingers or with another flat, but not sharp object. If nothing comes out, then the film will have to peel off and try to put it back in place again.
- Display mobile device it is best to wipe with a special computer napkin. With the same napkin, you can clean off all the dirt from the old film.
- Now we firmly take the device in our left hand, hold the edge of the film with our thumb and carefully glue it onto the glass so that no air gets under it.
If you were careful and your film is not too worn out, then everything should work out without difficulty.
Safety glass
How to remove air from under the protective glass? Here everything is a little more complicated, since excessive movements can violate the integrity of the protective accessory. We recommend that you familiarize yourself with the most common tips from experienced mobile users:
- Use driver's license or a plastic card in order to "squeeze" the air out from under the glass surface.
- You can use the most ordinary needle that everyone has at home. Take a needle and thread it under those places where air has accumulated. Carry out the procedure very carefully - you need to raise the edge, and then press it tightly so that air cannot get there.
- If you have fishing tackle on hand, you can use a line. Hook up the accessories with a fishing line and guide it until problem areas will not end. All that remains is to put the glass back in place and press it gently.
- Some experts recommend using a household hair dryer to fix defects. Warm up the glass of the mobile device at a distance of 20-30 centimeters, place it with the screen down on a flat coffee table and leave it under a press from books overnight. During this time, all the air should go out.
Important! You can also remove the glass in any of the following ways and clean its surface with a strip of tape. The adhesive tape will collect all dust and small debris, after which you can glue the protection back.
To avoid problems in the future, we have prepared a small list of recommendations for you:
- Do not apply the gluing procedure if your hands are dirty. Wash off sebum from your fingers, otherwise it can “leave marks” in your work.
- Both the protective glass and the film are best replaced in a humid, ventilated area. These precautions will help you avoid getting dust under the surface.
- Do not use too much effort when replacing the glass, otherwise you risk breaking it.
- You can use Dust Remover to remove excess dust.
- The most common medical syringe can be used to remove bubbles. Pass the “nose” and suck air out from under the surface of the film or glass.
