A total of up to 4 transmitters can be programmed into the system memory. Whenprogramming of the first transmitter, codes of all previouslyprogrammed transmitters. Thus, when attempting an unauthorizedprogramming the codes of additional transmitters the code of your "worker"
the transmitter will be automatically deleted from the system memory, and you will immediately noticethis attention.
ATTENTION: Remember that each operation must be performed within 15 seconds after the previous operation. If the 15-second interval is exceeded, the system will automatically exit the programming mode, which will be confirmed by one short and one long siren beeps. If during programming the ignition was switched off, the system will also immediately exit the programming mode, and you will hear 1 short and 1 long siren beeps.
1. Disarm the system, get into the car and turn on the ignition.
2. Within 15 seconds after turning on the ignition, enter your personal codesystem shutdown or press and release the Valet pushbutton switch 1 time (if function no. 12 is programmed as "Valet"). In 2 seconds youhear 2 short siren signals. This will also disable the AntiHiJack mode (if it was previously activated).
3. Within 15 seconds after the siren beeps, press the pushbuttonValet 3 times. You will hear 1 short siren beep and the LED will start slowlyblink to confirm that the system is ready to program a new transmitter.
4. Press and hold the button of the new transmitter until youhear a long siren beep confirming that programminga new transmitter has been produced. The system LED will light up.continuously as long as the transmitter button remains depressed.
ATTENTION: After programming the first transmitter, the codes of all transmitters previously programmed will be erased from the system memory.
5. Release the transmitter button. The LED will start flashing slowly again, confirming that the system is ready to program the next transmitter.
6. Repeat steps 4 and 5 to program all remaining transmitterssystems.
ATTENTION: When trying to program the 5th transmitter, the code of the firstthe programmed transmitter will be "erased" from the system memory, whentrying to program the 6th transmitter, the code of the second transmitter will be"preempted" from the system memory, and so on. The code of the same transmitter canbe programmed 4 times.
7. To exit the transmitter programming mode:
-
turn off the ignition or
-
wait 15 seconds without taking any action, or
-
press the Valet pushbutton switch again
You will hear 1 short and 1 long siren beeps, confirming thatthe system has exited the programming mode.
Car security system with function
remote engine start and 2-way communication
ALLIGATOR S-800RS
INSTALLATION INSTRUCTIONS
Attention! This security system is designed to be installed
only for cars with gasoline engine and only with manual
timid gear shifting.
Warning! Security measures
Please observe the following safety precautions at all times:
♦ This security system is a complex electronic device, therefore its installation
should only be carried out by a qualified technician from an authorized service center.
♦ Provided correct installation, this system allows you to remotely start the engine auto-
mobile when a signal is sent from the transmitter. Never
do not use the remote function
engine start if the car is in a place where the required ventilation is not provided
tilation. The safety measures listed below must be observed primarily by the users themselves.
teacher; however, the installer should be sure to familiarize the user with these safety measures.
nosti.
1. Never use the remote engine start function while the vehicle is in
completely or partially enclosed space without ventilation (for example, in a garage).
2. Responsibility for correct use key fobs-transmitters and their storage in such a place,
where children and outsiders cannot take them, it lies entirely with the owner. Manifestation of increased
attention will avoid accidental remote starting of the car engine.
3. The car owner must install a carbon monoxide (carbon monoxide) detector in the residential
the room, which is located next to the parking lot. All doors leading out
living quarters into a garage (closed or partially closed parking space)
must be permanently closed. Responsibility for complying with these security measures
face lies with the owner of the car.
♦ Non-compliance with the rules and procedures of use security system may result in the application of material
serious damage, injury or death of people. Therefore, never start the engine remotely.
vehicle if it is in gear.
♦ After installing the remote start module of the vehicle, immediately check the correct
the correct operation of the system in accordance with the procedure given in this manual. Installation
should only be carried out by a qualified technician from an authorized service center. Ra-
bot of the system of remote start of the car engine in the case when the car is
is in gear, completely contradicts the algorithm of work that is provided
for this module. The ability to operate the remote engine start system
under the specified conditions may result in material damage or injury to the
shooting people. You must immediately stop using this system,
mount or disconnect the installed remote engine start module for the car
beat. In this case, the manufacturer does not bear any responsibility and does not reimburse the costs of
installation and dismantling of the system.
Car security system
with remote start function
motor and 2-way communication
