Cars of the French concern Renault are in the top five among russian buyers... Qualities such as reliability, low gas mileage and modern appearance attract many domestic motorists. However, the French manufacturer, like others, also sometimes makes mistakes. One of them is the low-quality wiper blades on the Logan model. Of course, few people pay attention to such an insignificant problem, but it is the wipers that eventually become the No. 1 problem for Russian drivers.
1
After the first month of operation of Renault Logan, the first thing that catches the driver's eye is a little strange. The fact is that on almost all foreign cars, washers work synchronously with the wipers. On Logan, the opposite is true. The washers will not start when the wipers are turned on. Of course, this feature of the wiper blades has its supporters. However, most car owners consider this a big defect, which is very annoying during the operation of a popular foreign car. Fortunately, there is a solution to this problem. Furthermore, the manufacturer has equipped Logan with everything needed to replace the wipers. The driver is only required to have instructions, wiring and skillful hands.
Another surprise for Renault buyers will be the size standard brush wiper. The standard dimensions of these parts are 55 cm each, both for the driver and for the passenger. In this regard, the wipers wipe only an insignificant part of the glass surface, and everything else remains unaffected. It would seem a trifle, however, during heavy rainfall, a large amount of water flows down precisely from the parts of the glass "ignored" by the wipers. Renault Logan fans even dubbed this defect "snot".
To save your nervous system and get rid of such troubles, consider the most popular options for dealing with the ineffective work of wipers.
2
Increasingly, various Internet forums discuss the issue of overcoming gaps during the operation of windshield wipers. One of the most effective solutions a similar problem is the replacement of standard wipers with parts of different sizes. The wiper blades are considered optimal, the length of which is 65 cm for the driver's seat and 55 cm for the passenger.
Depending on the manufacturer, the size of the brush can be larger or smaller. but required condition - The length of the driver's wiper should be longer.
When choosing a wiper blade, you also need to pay attention to such a parameter as the design of parts. Frame wipers have proven themselves poorly during winter operation. The owners of such parts often have to pick ice from the holes between the rubber band and the part frame. If you don't do this regularly, the wipers will skip over certain areas of the glass.
Things are a little different with frameless wipers. Manufacturers of such parts often complete their products with special indicators that notify the driver about wear. At the end of the replacement of standard wipers with frameless ones, it is necessary to remove from new parts protective filmsto see the indicators clearly. As they wear, the latter will change their color.
Another important advantage of the frameless wiper blade is the tight contact with the glass. Many models of such wipers have individual design featuresthat allow you to adjust to any windshield. Winter options frameless wipers equipped with special protective covers that prevent parts from icing.
IT IS IMPORTANT TO KNOW!
Every motorist should have this universal device to diagnose your car. Now, without an autoscanner, it's just nowhere!
Read, reset, analyze all sensors and configure on-board computer car you can independently using a special scanner ...
An important nuance, which should not be forgotten when buying wipers, is the presence of spoilers. The wiper blades, complete with spoilers, adhere perfectly to the glass at any vehicle speed.
3
Refinement of trapezium traction is a rather laborious process that will take a lot of your time. But by doing this job, you will get rid of "snot" once and for all. To fine-tune the trapeze rods, you need some tools and experience in welding.
First, we take out the parts that require improvement. To do this, we act according to the following algorithm:
- We open the Renault Logan hood and remove the plastic trim, under which is the base of the wiper blades.
- Dismantle the bonnet seal and the plastic grille.
- We see brushes in front of us. Their position is worth remembering, so that you can later install them in place in the same way.
- We remove the leashes of the wipers. To do this, gently pull them towards ourselves.
- We dismantle the plastic pads that are under the leashes.
- A pin opened in front of us, from which we unscrew the nut and remove the washer.
- Turn off the wiper motor block and unscrew the bolt holding it.
- Unscrew the nut and washer on the wiper arm.
- Dismantle the lever by pulling it slightly towards you.
Then we take out the rod from the hinge of the lever and mark the cut point on it. To make the wiper blades work more efficiently, it is better to cut about 5-8 mm of metal between the bend of the rod and its fastening. After the cutting procedure, we weld the pieces of traction back. We check the seams for irregularities and if there are any, we carefully eliminate them by grinding. After that, we collect all the details in reverse order.
After the work done, Renault Logan wiper blades will completely wipe the windshield, regardless of the intensity of precipitation.
Do you still think that car diagnostics is difficult?
If you are reading these lines, then you have an interest in doing something yourself in the car and really savebecause you already know that:
- STO lomat big money for simple computer diagnostics
- To find out the error, you need to go to the specialists
- Simple wrenches work in the services, but you can't find a good specialist
And of course you are tired of throwing money away, and there is no question of driving around the service station all the time, then you need a simple ELM327 AUTOSSCANER that connects to any car and through a regular smartphone you will always find a problem, redeem CHECK and save a lot! !!
We have tested this scanner ourselves on different machines. and it showed excellent results, now we recommend it to EVERYONE! So that you do not fall for the Chinese counterfeit, we publish here a link to the official AutoScanner website.
The size of Renault Logan wiper blades becomes a very important parameter in the event that you decide to replace standard wipers with more modern and sophisticated ones. Cleaning system windshield consists of the following structural elements:
- cleaner brushes;
- brush drive mechanism;
- washing lines;
- washer fluid storage tank;
- the pump for supplying fluid for washing.
For a number of reasons, installing new wipers on Logan is one of the most common operations performed by the owners of this model immediately after purchasing it. New wipers generally perform significantly better than standard wipers and have a much longer lifespan.
Reason for replacing wipers
The main reason for replacing wipers Renault Logan - their strange work, which has long been attributed to the generic "diseases" of cars of this brand.
The fact is that most modern cars are armed with such a windshield cleaning system in which the windshield wipers work synchronously with the windshield washer.
Renault Logan wipers do not start the washer in the on position, as a result, the glass is cleaned dry until the driver manually starts the device into operation. Naturally, this creates certain inconveniences when driving, since the driver is distracted from the road, which can lead to the most dire consequences.
In addition, the design of standard wipers has another unpleasant feature - these are the same brush sizes for both the driver and the passenger. They are 55 cm long. Such a length of the brushes does not allow them to completely clean the windshield of the car, since they simply do not capture a small part of it, on which water accumulates. Renault Logan fans even gave a nickname to this phenomenon, calling it pejoratively "snot".
Car owners claim that a washer reservoir is installed here too small, as a result of which washer fluid quickly runs out in bad weather. At the same time, removing the washer reservoir presents significant difficulties due to its inconvenient location.
Selection of new wipers
You can get rid of these problems by installing new wipers of a different size on Logan, as well as by synchronizing the work of the wipers with the washer. Experienced car owners it is advised to purchase these accessories, the size of which will be 65 cm for the driver's seat and 55 for the passenger. The shape, device, method of attaching the wipers can be any, but remember that their size should be different in any case.
What are the best windshield wipers for Logan is a controversial issue, since each driver chooses a design for himself. So, some people like it when the brushes are more rigid, while others prefer designs that have shields in service. However, when choosing these accessories, one thing must always be taken into account: on Renault Logan, frame wipers have some problems during operation in winter. This is due to the fact that moisture can freeze between their rubber pad and the frame.
In this regard, when the wipers are replaced, it makes sense to purchase frameless brushes. The fact is that the structure, which does not have a frame, allows the cleaning surface to be attached to a rather complex structure with several points of support, which is called a "rocker". As a result, the brushes do not freeze to the glass, ensuring that the wiper is always ready for work.
In addition, frameless wipers are armed with a wear indicator for their brushes. FROM technical point vision, such an indicator is a strip that will change color as the brushes wear.
Frameless brushes, as a rule, are small in size, tightly pressed against the glass and equipped with spoilers that prevent them from being blown off by the incoming air stream.
Replacing the wiper blades with Renault Logan is easy enough. The fact is that there is a special latch on the rod of this device. By turning the brush in a special way, you can open the latch and remove it. Installing a new brush is done in the same way. Replacing non-standard wiper blades is easy, since their attachment point is no different from standard samples.
At the same time, the main "disease" of the regular Logan wipers - the "snot" can be defeated only by upgrading the trapezium traps, which will allow the brushes to capture areas of the windshield that are inaccessible to a standard accessory. In this case, you will have to resort to welding.
To do this, after dismantling the rod, from 6 to 8 mm of metal is cut from it between the fastening of the rod and its bend. Next, the remaining pieces are welded together, and the seam is cleaned from irregularities. After that, the thrust returns to its place.
In principle, these improvements are simple, and they can be done independently, in contrast to the modernization of the glass washer system. So, for example, some craftsmen change the washer pump, increase the size of its tank, change nozzles, etc.
ALREADY SHARED
Cars of the French concern Renault are among the five leaders among Russian buyers. Such qualities as reliability, low consumption of gasoline and modern appearance attract many domestic motorists. However, the French manufacturer, like others, also sometimes makes mistakes. One of them is the low-quality wiper blades on the Logan model. Of course, few people pay attention to such an insignificant problem, but it is the wipers that eventually become the No. 1 problem for Russian drivers.
1 What's wrong with the wipers of the "Frenchman"
After the first month of operation of Renault Logan, the first thing that catches the driver's eye is the slightly strange operation of the wiper blade. The fact is that on almost all foreign cars, washers work synchronously with the wipers. On Logan, the opposite is true. The washers will not start when the wipers are turned on. Of course, this feature of the wiper blades has its supporters. However, most car owners consider this a big defect, which is very annoying during the operation of a popular foreign car. Fortunately, there is a solution to this problem. Furthermore, the manufacturer has equipped Logan with everything needed to replace the wipers. The driver is only required to have instructions, wiring and skillful hands.
- Length of wiper blades Kalina
- Chevrolet Cruze Wiper Blades
- How to install the wiper blades
- Autoscanner for self-diagnosis of any car
Another surprise for Renault buyers will be the size of the standard wiper blade. The standard dimensions of these parts are 55 cm each, both for the driver and for the passenger. In this regard, the wipers wipe only an insignificant part of the glass surface, and everything else remains unaffected. It would seem a trifle, but during heavy rainfall, a large amount of water flows down from the parts of the glass "ignored" by the wipers. Renault Logan fans even dubbed this defect "snot".
To save your nervous system and get rid of such troubles, consider the most popular options for dealing with the ineffective work of wipers.
2 How to choose new wiper blades on Renault Logan
Increasingly, various Internet forums discuss the issue of overcoming gaps during the operation of windshield wipers. One of the most effective solutions to this problem is to replace standard wipers with parts of different sizes. The wiper blades are considered optimal, the length of which is 65 cm for the driver's seat and 55 cm for the passenger.
Depending on the manufacturer, the size of the brush can be larger or smaller. However, a prerequisite is that the length of the wiper for the driver must be larger.
When choosing a wiper blade, you also need to pay attention to such a parameter as the design of parts. Frame wipers have proven themselves poorly during winter operation. The owners of such parts often have to pick ice from the holes between the rubber band and the part frame. If you don't do this regularly, the wipers will skip over certain areas of the glass.
Things are a little different with frameless wipers. Manufacturers of such parts often complete their products with special indicators that notify the driver about wear. At the end of the replacement of standard wipers with frameless ones, it is necessary to remove the protective films from the new parts in order to clearly see the indicators. As they wear, the latter will change their color.
Another important advantage of the frameless wiper blade is the tight contact with the glass. Many models of such wipers have individual design features that allow them to adapt to any windshield. Winter variants of frameless wipers are equipped with special protective covers that prevent parts from icing.
An important nuance, which should not be forgotten when buying wipers, is the presence of spoilers. The wiper blades, complete with spoilers, adhere perfectly to the glass at any vehicle speed.
3 We wipe the "snot" Renault Logan by modernizing the trapezoid trapezoid
Refinement of trapezium traction is a rather laborious process that will take a lot of your time. But by doing this job, you will get rid of "snot" once and for all. To fine-tune the trapeze rods, you need some tools and experience in welding.
First, we take out the parts that require improvement. To do this, we act according to the following algorithm:
- We open the Renault Logan hood and remove the plastic trim, under which is the base of the wiper blades.
- Dismantle the bonnet seal and the plastic grille.
- We see brushes in front of us. Their position is worth remembering, so that you can later install them in place in the same way.
- We remove the leashes of the wipers. To do this, gently pull them towards ourselves.
- We dismantle the plastic pads that are under the leashes.
- A pin opened in front of us, from which we unscrew the nut and remove the washer.
- Turn off the wiper motor block and unscrew the bolt holding it.
- Unscrew the nut and washer on the wiper arm.
- Dismantle the lever by pulling it slightly towards you.
Then we take out the rod from the hinge of the lever and mark the cut point on it. To make the wiper blades work more efficiently, it is better to cut about 5-8 mm of metal between the bend of the rod and its fastening. After the cutting procedure, we weld the pieces of traction back. We check the seams for irregularities and if there are any, we carefully eliminate them by grinding. After that, we collect all the parts in reverse order.
After the work done, Renault Logan wiper blades will completely wipe the windshield, regardless of the intensity of precipitation.
Renault Logan cars in Russia are in the TOP-5 of the most popular models on the market. High reliability, efficiency and attractive appearance are very appealing to our customers. As the saying goes: Only those who do nothing do not make mistakes! This allegory just applies to the manufacturers of Renault Logan.
A little - a lot, the problem lies in the basic brushes windscreen ... Of course, at the first time of operation, few people pay attention to this annoying miscalculation, but after the lapse of time it becomes an annoying problem for loganovods.
How to get rid of such defects and modernize the wipers system, read below in our article.
After some time since the beginning of operation, motorists notice a very unusual feature when working with wipers. The thing is that on most popular foreign cars they work simultaneously with the windshield washer, but on Logan everything turns out differently. When the wipers are turned on, no water is supplied. And this is not a problem in the pump, which is such a feature of the work.
Of course, this option of work has its supporters, however, the absolute majority of Loganovodov agree that such operation is inconvenient and requires improvements. Fortunately, there is a solution to this problem, only instructions, a little experience and the required amount of wiring are required.
Another unpleasant "surprise" for Renault Logan owners is the standard size of the windshield wiper blade. Its length is 55 centimeters, both from the driver and the passenger side.
Therefore, during operation, they capture only a small part of the glass surface, leaving the remaining areas intact. This may seem like a small problem, but when precipitation falls, it is in such untouched areas that moisture flows from the glass, which in turn causes discomfort. Among motorists, this situation has been nicknamed - the "snot" effect.
This is the result of standard wiper operation.
And so with the modernization performed. As you can see, the triangle along which all the dirt flows has disappeared.
What wipers to choose on Renault Logan?
To date, there are many open topics on the Internet on the forums about the problem of wiper blades on Renault Logan. One of the most popular answers to this problem is replacing regular wipers with parts of a different size.
The ideal size of the driver's side wiper 65 centimeters, and the passenger 55 cm.
Depending on the manufacturer, the size may differ slightly, but there is only one regularity, the length from the driver's side should always be greater.
Step by step process for replacing wipers
Please note that when installing frameless brushes, you may need a special adapter (which in most cases comes with the kit).
We carry out the modernization of the trapezoid trapezoid
The process of changing the trapezoid trapezoid is a rather complicated process that will take you both energy and time. But as soon as all this work is done, the "snot" effect is guaranteed to disappear.
In order to carry out such manipulations you will need hand tool, welding machine, straight arms and strict adherence to our instructions.
- We open the hood and remove the plastic cap from the protective grill.
Using a flat screwdriver, gently pry off the piston.
- Then remove the bonnet seal and the plastic grill that covers the motor with the wiper arm.
With a little effort, the plastic grill and the seal will come off their place.
- After access is open to the brushes, we remember the approximate location of the wipers in order to subsequently install them in their places. You can mark with marker.
- We unscrew the nuts and remove the washers from the wiper leashes.
To make it easier to rip off the nut, you can pre-treat it with WD-40.
- To remove the leashes themselves, they must be swung from side to side and pulled towards yourself.
- Remove the plastic cover and unscrew the nut and washer from the pin.
Remove the plastic protection by prying it from below with a screwdriver.
- Remove the wiper power connector.
It is better to disconnect the contact with a flat tip of a screwdriver.
- Unscrew the motor mounting bolt from the body.
The motor mounting screw can be easily unscrewed using the socket head to "10".
- Pulling the lever, dismantle it.
- After the entire trapezium has been dismantled, remove the nut and washer from the passenger traction and release it.
- In order for the modernization to be successful, it is necessary to cut from 5 to 8 mm of metal from the traction, and then weld the ends together.
It is best to cut off some of the pull with a hacksaw blade.
- After welding, we check everything for irregularities and grind them.
This is what the thrust looks like after work done.
- We collect all the parts in the same way as for removal, not forgetting to grease all friction points with grease.
After carrying out such work, you can be sure that the Renault Logan wiper blades will wipe most of the glass without leaving any unnecessary marks.
The process of removing the motor of the wipers with a trapezoid (video)
Every motorist who appreciates the safety of both his own and those of others knows perfectly well that replacing the wiper blades, if they do not cope with their work, before preparing their car, including Renault Logan, for the next season change, necessary measure... In this article we will talk about what you need to know when the wipers are replaced, as well as which ones to choose better. How can you make regular wipers with a light upgrade work much better.
How to choose wipers
Many owners of "French" Renault Logan, and other car models, know very well that the following suddenly happens: when you turn the wipers switch to the "on" position, the brushes, as expected, slip on the windshield, but instead of a cleaned surface, why it turns out even more dirty glassthrough which you can hardly see what is happening on the road.
When this happens, it becomes obvious that the brushes have lost their functionality, and an urgent replacement of the wiper blades is required. And here there are quite natural questions: how are the wipers replaced, and what is the size of the wipers on my model, where and which brushes to choose? Often, Renault Logan drivers immediately begin to think about buying original components for this car system, which have the appropriate size of brushes for the Renault Logan model, and, as we found out, are of the highest quality, and will be used for a long time and regularly in comparison with non-original products manufactured by other companies ...
I would like to note right away that the size of the standard brushes for Renault Logan cars is 508mm in length. Original wipers have a frame-type design. What are their advantages and disadvantages? Such wipers have a large number of metal moving elements in their design.
Each time you press the switch, part of the brush can fall off, and thus the car owner will have many inconveniences. After all, ahead, waiting for him complete replacement wiper blades.
Among other things, by choosing the correct size of wipers, the original frame wipers do not do their job well enough. winter period... Each movable joint freezes to the adjacent one, and the rubber water squeegee ceases to be flexible and does not fit snugly against the windshield. To get out of this situation, the driver will constantly have to lubricate the brush frame with grease, but this solution is not long-term, and after a while, this manipulation will have to be done again.
Another serious disadvantage of the wiper design for Renault Logan is the very unfortunate size of the wipers. What are the problems with this? To begin with, all the "charms" of this defect will be felt during the rain, when water flows from the roof of the car onto the windshield, and you need to turn on the wipers more often to remove excess rain water.
In a Renault Logan car, during a heavy rain, a drop begins to drain right in the middle of the windshield, because the brushes do not reach, due to their design feature, and you cannot get rid of these drops in the middle.
We regulate the work of car wiper blades
Thanks to the experiments carried out by the owners of the Renault Logan model, it was possible to understand that the drop that appears on the windshield is formed due to the peculiarity of the brushes and leashes on which they are actually installed. What to do in this situation? The very first method is to rework rather than completely replace the wiper blades. For everything to be perfect, you need to know the improved size of the wipers, which will be able to remove the flow of water from the glass. And then, the windshield cleaning system will begin to function much better.
To make this upgrade, you need to adjust the size of the brushes or leads. For this, the wipers are replaced with non-original ones, but this does not mean that they should be of lower quality. The main thing is that the wiper on the driver's side is slightly longer, but on the passenger's side it is a little shorter. Practice shows that the brushes will work perfectly and the windshield will always be clean. And to make a replacement, you need to know how to remove unsuitable wipers.
In addition to such a simple solution to an urgent problem in a Renault Logan car, such as replacing original wiper blades with non-original ones, a method for which you need to have certain tools and more time spent is the revision or repair of the wiper trapeze. To do this, you will need to know how to remove the leashes from the mount, and dismantle the trapezoid to shorten it.
What do you need to do to make a replacement? First, we remove the brushes from the fasteners, for this a simple wrench is used. The nut is often easy to unscrew.
When you have removed the brushes and leads, you need to carefully remove the cover, which is under the glass and is purely decorative, and you can easily pry it off with your hand. Then a more difficult stage remains.
So, the revision is carried out as follows: first, we dismantle the trapezoid and cut it off where the bend begins. After that, we shorten the straight section by approximately 6-8mm, and then welding follows. The weld will need to be cleaned and reassembled in the reverse order, and when the switch is triggered again, the streams of drops on the glass will no longer bother you.
We modernize trapezium traction
It takes a lot of time to refine the trapezoid linkage. However, this will allow you to forget about the water on your windshield forever. Competent revision of the trapezoid requires a little welding skills and special tools, and in this case there is no need to replace the wipers.
- We remove the thrust from the body, for this you need to do the following manipulations.
- We open the hood and remove the special plastic nozzle, where the base of the wiper blades is hidden.
- Remove the plastic grille and bonnet seal.
- Be sure to remember the position of the brushes in order to put them back in their place correctly, otherwise they will not work.
- We remove the leashes in order to do this easily and simply, you need to pull them towards yourself, swinging a little.
- Remove the plastic pads that are under the leashes.
- After that, you will see a pin from which you need to twist the nut and remove the washer.
- We must turn off the wiper motor unit.
- On the lever, we twist the nut and, accordingly, the washer.
- To easily remove the lever, you need to pull it up with 2 screwdrivers.
- Remove the rod from the lever hinge.
Next, you need to mark the place of the cut on the removed rod. In order for the brushes to work normally afterwards, 6-8mm of metal should be cut between the fastening of the rod itself and its bend, as mentioned above. After marking, you need to cut off all excess. Then you need to weld the pieces of traction into one and process the seam so that there are no irregularities. After that, the thrust should be returned back and everything that was disassembled should be collected.
Let's sum up
Repairing or replacing the windshield wiper blades on Logan is an important and necessary moment. From their correct work depends on the safety of driving during bad weather, plus ride comfort.
