How to properly cover a car with foil. Technique for the correct pasting of a car with film

Car wrapping with vinyl is increasingly in demand by motorists. This method allows you to make the vehicle unusual, noticeable and original, protects against minor damages - chips, scratches and masks existing ones.

Vinyl can be clear, colored, reflective, fluorescent, smooth or textured, so selection problems are rare. The situation with the gluing process itself is more complicated.

Advantages and disadvantages

Pasting has a number of advantages and disadvantages. The positive aspects include:

aesthetic appearance;
ease of execution;
immunity to natural phenomena (rain, snow, hail, wind, scorching sun);
protection of the body from minor damage;
disguise;
cost-effective compared to conventional car painting or airbrushing.

Negative points:

if the car was partially pasted over, then there is a risk of color differences after removing the cover;
in the case of a poorly painted surface, there is a possibility that the vinyl will be removed along with the coating;
the need for gentle care.

Types of gluing and material calculation

There are two ways of gluing:

dry - a film made of auto vinyl instantly adheres to a dry surface. Of course, the indisputable advantage is the speed of the process and the long service life of such a coating, but in case of unsuccessful gluing, it is very difficult to fix the flaws, so it is better to entrust the work to professionals;
wet - simpler in execution, in case of errors, the film can be removed. However, if the work is not done carefully enough and water gets into the interlayer, bubbles may form on the vinyl. It is easier to glue the car with foil with your own hands in this way.

To calculate the required amount of film, you can contact a car dealership or a specialized store, where sales consultants can name the exact footage for a particular brand vehicle... When buying, it is important to pay attention to the following nuances:

the type of film on which its ability to stretch depends;
availability of skills. For those who are going to glue for the first time, it is better to purchase about 2 meters in reserve, since surely some part of the material will be pulled, torn, overheated;
the need for bends, that is, in any case, the material does not need to be taken "back to back".

How to cover a car with vinyl?

First you need to stock up the necessary tools and prepare the place. For pasting you will need:

napkins made of soft, lint-free material;
scissors;
stationery knife or scalpel;
squeegee made of rubber or felt;
masking tape;
building hair dryer (you can use the usual one, but the procedure can be delayed);
spray bottle with soapy water. To prepare it, an ordinary dish detergent is mixed with water in a ratio of 1:10;
sealing glue;
degreasing agent.

It is best to glue the surface of the body in the garage.

It is very important that the room has good all-round lighting, moderate humidity and an air temperature of at least 20 ° C. If these conditions are not met, the film either simply does not stick, or it will last only a few months.

For pasting the body on the street, it is better to choose a warm (+ 20-30 ° C) and windless day.

It requires agility, certain skills and scrupulousness, so beginners are better off starting with small and discreet elements.

Process description

Bonding the protective surface consists of the following steps:

Pasting a car with vinyl film begins with a thorough cleaning of dust and dirt (to facilitate the process, you can contact a car wash). Then you need to treat the surface of the body with a degreasing agent, wipe with a dry cloth.
Without tearing off the paper base, attach the film to the intended location. Mark the boundaries with cooked tape. Cut the required cover piece, leaving a small margin on all sides.
Laying the film on a horizontal surface, tear off the paper base at an angle of 30-40 °, making sure that the film does not stick to itself. Apply soapy water evenly and generously to the part of the car to be pasted.
Now we paste over the vehicle. We apply the vinyl covering to the body surface, constantly pulling and fixing it at the upper corners. Using a squeegee, we roll the film from the center to the periphery, heating it with a hairdryer. During heating, the hair dryer is kept at a distance of 20 cm. The vinyl must be warmed up evenly, in no case should it overheat, so the flow of hot air must constantly move. If vinyl big size, then the pasting will be more successful with someone's help.
After pasting the car with vinyl has been completed, you need to once again thoroughly walk with a hairdryer over the entire surface - this helps to activate the adhesive.
Trim off excess edges, leaving a margin of 0.5 cm, then carefully glue them with sealing glue. Wipe the entire glued surface with a dry cloth.

Vinyl wrapping of the car is finished, but it will only set in a day. The covered vehicle must not be washed for 7-10 days. If the process seems too complicated and you are not confident in your own abilities, it is better to paste over the car in the cabin. This will help to avoid wasted financial costs and disappointment as a result.

Many drivers who want to make their car more effective and aggressive decide to cover it with carbon films. However, not everyone can do this task correctly the first time. In order for gluing carbon vinyl to give a positive result, we will consider all the subtleties of performing such work in more detail, and also watch a video on this topic.

1 "Wet" method of gluing carbon film

How to glue carbon film? There are two ways. If you are doing such an operation with your own hands for the first time, then the so-called “wet” method of film application is suitable for you. It got its name from the use of soapy water, which prevents the vinyl parts from sticking together.

At the beginning of work it is necessary to thoroughly clean and degrease the surface of the car. Next, we take vinyl and measure out the amount of film we need. We put a small amount of soapy water on its surface, separate the film from the paper and moisten the vinyl from the adhesive side.

Apply water to inner side the film must be carefully, since the retention time of the latter on the car body depends on this. If there is too little or too much water, the vinyl will not last even a month.

Next, we take the finished film and gently apply it to the surface of the car. We take a spatula and evenly “expel” the water from the film. This is best done from the center to the edges of the vinyl. After there is no water left under the film, dry its upper part with a regular household hair dryer. Then we smooth the vinyl again with a spatula. If there are curved places left, smooth them out with a primer. After that, you need to give the product about 7 minutes to dry.

At the final stage of wrapping with vinyl, heat the film with a hairdryer and bend the edges to the primer. Carefully cut off any excess carbon vinyl. After that, we leave the car for 12 hours to dry it completely. A vivid example of how to paste over a car with vinyl can be seen in the video.

2 How to "dry" glue vinyl

This method of gluing the carbon film is more complicated. It will take much more time and effort to complete. It is only necessary to use the “dry” method if you have previously dealt with vinyl gluing. To get started, we need:

dry room, the temperature in which must be at least 20˚С;
a clean car, on the body of which there should be no rust, scratches and traces of oil, is best pasted over recently;
construction hair dryer, which will help to paste over the car much faster;
special knife for working with film;
devices for secure fixation of the carbon film.

As with the wet vinyl method, the car body must be cleaned and degreased. You need to take care of the absence of scratches and rust on the car body. We take the film and separate it from the cardboard lining. Gently apply its upper part to the car body and begin to smooth the product from the center towards the edges. All parts of the vinyl should be equally pressed against the surface of the car. For the best effect, use a spatula. If in the process of work you allowed the formation of bubbles or folds - it's okay. Peel off this part of the film and re-stick it.

Then we take a building hair dryer and heat the vinyl. In this way, we activate the work of the glue and the carbon film will “grow together” with the car body faster. However, do not get carried away to keep the vinyl from overheating.

After heating the product, we take a spatula and re-smooth it on the body as shown in the video. After that, cut off the excess vinyl edges and leave the car in a dry and warm room for 6-7 hours.

That's all - the do-it-yourself vinyl wrapping work is over. By the way, performing this operation, you can at the same time produce machines that also require a warm and dry room.

3 Features of buying a carbon film

Before sticking on the carbon film, we need to purchase a quality product. It turns out that this is not so easy to do. Counterfeits in our market are increasingly common every year. However, this does not mean at all that it is unrealistic to buy high-quality vinyl in our country.

As practice shows, the highest demand among buyers is for products for covering companies. HEXIS, Orafol, KPMF, Magical carbon, 3M... Films from these manufacturers have earned their popularity due to excellent quality, wide range and durability. All this cannot be said about Chinese "cheap stuff", the packaging of which is riddled with hieroglyphs. It is better to bypass such a product as far as possible.

In addition to the manufacturer, a very important factor when buying vinyl is a store... In big cities it is very easy to find specialized shops that sell products only from specific 1-2 companies. The goods in such stores are always of high quality and durable. In no case do we recommend buying adhesive film in the markets and on the Internet. While the order is delivered to your city, the vinyl may warp from cold or moisture. Carbon films sold in the markets very often deteriorate due to exposure to direct sunlight, which negatively affects their quality and ability to stick to the car. Many videos have already been shot about this, where unlucky drivers complain about the poor quality of the films they bought.

Having an understanding of the intricacies of buying and gluing, it is right to do external tuning everyone can do it with their own hands. The main thing is patience, because pasting any car with carbon does not tolerate haste.

X Do you still think that car diagnostics is difficult?

If you are reading these lines, then you have an interest in doing something yourself in the car and really savebecause you already know that:

STO lomat big money for simple computer diagnostics
To find out the error, you need to go to the specialists
Simple wrenches work in the services, but you can't find a good specialist

And of course you are tired of throwing money down the drain, and there is no question of driving around the service station all the time, then you need a simple ROADGID S6 Pro AUTOSCANNER that connects to any car and through a regular smartphone you will always find a problem, extinguish CHECK and not bad save !!!

We have tested this scanner ourselves on different machines. and it showed excellent results, now we recommend it to EVERYONE! So that you do not fall for the Chinese counterfeit, we publish here a link to the official AutoScanner website.

Painting a car is expensive, so car owners are increasingly choosing to cover a car with a film material. By covering the car with a film, you can easily change the color of the vehicle. By purchasing material with inscriptions and stickers, you will create an unusual car design. Car owners do the pasting on their own, or entrust the work to masters at the service station.

How realistic is it to cover the car with a film with your own hands

Yes, it is not necessary to contact the service station if you have the skills to work with the material, or if you want to save money. Keep in mind that labor is painstaking, it is better to start with inconspicuous parts of the machine. When you are more experienced, start applying the film to the hood and other body parts.

Why is the car covered with a film

The film makes appearance car attractive. The material has not only a decorative purpose. The film coating performs the following utilitarian functions:

protects the body from damage: chips, scratches,
colorless film retains the original paintwork of the body, colored material changes the appearance of the body,
the film is removed easily without leaving marks,
you can remove the old material, then cover the body with a new film of a different color.

Buy material by making stock. This is important if this is your first time covering the car with plastic. Pay attention to the preparation of the body, the result of the work depends on it.

Read in our material about which will be available in Russia.
To buy a quality reverse alarm, look at which manufacturers you can trust.

Which film to buy?

There are three types of film sold in stores. First, determine your preferences and goals that you are going to achieve, then choose the material. The film for pasting the machine is of the following types:

vinyl,
carbon,
anti-gravel.

Vinyl takes an intermediate position between carbon and anti-gravel films. Cars covered with this material look good. Carbon film looks stylish and is an inexpensive material. Choose anti-gravel if you like to travel, or drive on gravel trails. Such a film will protect the vehicle well from chips.

How much does the film cost on the car

The cost of anti-gravel is from 2500 rubles. The material is resistant to punctures and chemical contaminants, scratches. You will buy carbon film for 450 rubles. The price of vinyl material is from 2000 to 8 thousand rubles.

The material is available in specialized stores. Sellers will help you choose the right film for any vehicle.

How to cover a car with a film: stages of work

The work of pasting a vehicle can be divided into three stages:

Buy stuff.
Prepare your tools.
Clean the surface before gluing.
Cover the car with plastic wrap.

Determine where you will apply the film. Prepare the body, the quality of the covering depends on it. Go to a car wash, or self-clean the body of dirt. Use detergents, apply solvent or abrasive clay to dirty areas. Clean the outside and inside of the body, as well as where you wrap the edges of the film.

The material is glued to a wet or dry surface. The last method is used by craftsmen, it is more difficult than sticking on a wet surface, it requires certain skills. When deciding to stick the film on a dry surface, remember that the material sticks instantly. You only have one try to position the film correctly.

For beginners, masters recommend choosing the first method, which is based on sticking the film onto a wet base. The method is good because in case of unsuccessful application, the material is easily removed, it can be glued to a new place. Make sure that there are no air bubbles under the film.

The method of application on a wet base is suitable for bonding the bonnet, body decoration. When you decide to wrap the car completely, carefully drive the water out from under the film, directing it to the edges.

You will need the following tools:

squeegee made of felt or rubber,
stationery knife and scissors,
a spray bottle filled with soapy water, with
heating hair dryer,
soft rags.

Buy quality materials, use clean rags.

Try on the material, make markings, cut out a fragment. Remove the backing from the film, spray the body with soapy water. Put the stuff down. While heating with a hair dryer, smooth out the film with a squeegee. When finished drying, brush the area with a felt squeegee to remove the smallest air bubbles. Carefully trim off any remaining film. Heat the edges with a hairdryer, bend and glue.

Using a hair dryer, you will get a perfectly flat surface, the material will fit snugly. Heat the film evenly, the process is accompanied by polymerization. This increases the durability of the material, provides excellent adhesion, and makes the surface durable. Despite this, it is better not to wash the car in the first week after pasting.

How to cover a car with foil with your own hands (video)

Outcome

After finishing work, leave the car for a day in a warm garage. After that, you can leave by car. Do not use abrasive products to wash the vehicle, they will damage the film coating.

If you doubt that you can do the pasting on your own, then choose a service station or a specialized car dealership. The masters of the center will select the material, focusing on your needs, and will paste.

In specialized centers, car owners will order the body design. The cost of pasting is about 8 thousand rubles.

Pasting a car with a film with your own hands seems to be a simple process. In fact, the likelihood of spoiling auto vinyl, due to the lack of theoretical knowledge and practical skills, is extremely high. Let's consider how to properly glue the film on door handles, mirrors, in places of bends and depressions. Let's pay special attention to car vinyl styled like carbon, the work with which has characteristic features.

Tool, materials

To work you need:

squeegee, with the help of which the film is smoothed, air bubbles are expelled;
a clerical knife, which will be convenient to cut the remnants of the film;
spray, commonly used for the garden and vegetable garden. We need it to spray soapy water;
hairdryer. At temperatures above + 20 ° C, in the absence of a powerful building hair dryer, even a household one will do quite well;
degreaser;
a primer that enhances the adhesion of the adhesive layer;
paper napkins. These are used when painting a car to remove dirt and degrease. In order for the coating to serve for a long time, not to swell and keep up with the edges, the surface must be perfectly clean. If auto vinyl is not glued to a car that has recently left the walls of a car dealership, then we recommend buying clay for a car body. It will help remove stubborn resinous deposits, clean the dirt from micropores and cracks in the paintwork of the car. This will improve adhesion and extend the life of the film;
dry rags to remove residual moisture.

The carbon film or any other texture can be glued using a soapy solution (wet method) or dry. Car wrapping with a dry method provides a more secure grip and a better fit on bends, but is not very suitable for work without experience. A wet surface is more forgiving as it is easier to slide and lift the film to remove air.

Which films are easier to glue

If you are not experienced with car vinyl, which is likely if you are reading this article, we do not recommend choosing the cheapest films for your car. In view of bad quality, they are difficult to paste, since they have poor elasticity, are often prone to shrinkage and swelling. Understanding of many things will come to you only directly when pasting with your own hands. Therefore, in order not to spoil the expensive material, we highly recommend buying a small piece of the cheapest training tape. You can cover, for example, the plastic in the cabin in a carbon look, and only then proceed to pasting complex car parts and large areas.

For beginners, we recommend choosing a material with channels on the inner layer. It is much easier to remove air bubbles from under this vinyl. Also, do not train on carbon-like films, unless you glue it onto an inconspicuous small part of the interior. The rectangular structure of the image does not allow stretching the material, stylized as carbon, as distortion is immediately visible. Conventional car vinyl in this regard forgives much more mistakes, and therefore the first experience of pasting a car has a better chance of success.

Repair of paintwork damage

Vinyl material not only does not hide the defects of the car body, but can also make them more noticeable (especially if it is a matte finish or carbon film). Preferring auto vinyl to painting a car, you must understand that the preparation should be no less thorough.

Particular attention should be paid to areas of corrosion, since the corrosion process under the film will continue, which will very quickly lead to peeling or swelling of the auto vinyl.

If the car body is in a satisfactory condition, it is often enough to hide large chips and deep scratches... If the damage is not too severe, you can do without filling and priming. Otherwise, you need:

degrease the damaged area, clean with abrasive P120. Corrosion spots must be treated with a rust converter, and then primed with epoxy primer;
fill the defect with a universal putty;
clean the filler first with abrasive P120, and then into the finishing one P320;
prime the fillings with acrylic primer;
clean the soil with abrasive P320 at the initial stage and P600-P800 at the finishing stage.

We did not describe each of the processes, since we have already devoted separate articles to filling and priming our car.

Car preparation

The level of adhesion directly depends on the quality of preparation, therefore, its durability.

The car must be washed thoroughly. Best to use a sink high pressure, since our primary task is to knock out dirt from under the seals and grooves where the film will be tucked.
For high-quality pasting with a glossy, matte or styled carbon film, it is necessary to remove the moldings, door handles, antenna, etc.
Use cleaner if necessary bituminous spots... Wipe the surface with clay and water.
Using a squeegee and rags, clean all grooves, under the rubber bands, and the edges body partson which the film will be rolled.
Pay particular attention to the removal of silicone and fat deposits. Spray the surface with a degreaser, then wipe off the dissolved deposits with a dry cloth. It is also possible to use two wipes: moistened with degreaser and dry.

Primer, soapy water, cut

The recipe for the soap solution is quite simple: a few drops of a dish cleaner, such as Fairy, per liter of clean water.

The primer should only be used when necessary:

in places of difficult depressions and depressions, where film tension is required to remove folds;
along the edges of the body parts where the material will be wrapped;
inner edges wheel arches a car where there is sandblasting from wheels, vibration from lockers, etc.;
if for some reason you put an adhesive layer on the film, thereby reducing its adhesion properties.

The desire to play it safe and apply a primer around the perimeter of the car body elements is quite understandable. But this is superfluous if you followed the previous recommendations. Using a primer may even entail negative consequences... If you glue, for example, a carbon-look film on a poorly painted body element, then there is a possibility that after 3-4 years the film will be removed along with pieces of varnish.

We suggest watching tips on sewing in the video tutorial.

Self pasting

Since it is impossible to tell all the subtleties of work with your own hands, we suggest you watch a video of the work of professionals.

Air removal, correct turns, carbon

After warming up the film and wrapping, do not immediately cut off the remains. Let the material cool. We suggest watching the video for the correct technique for removing air and turns. If you are going to tune your car with carbon film, we recommend that you study the YouTube channel ValdeVay Auto Vinyl Lessons , on which the specialist shares real experience pasting a car with vinyl film.

What tools and materials will be required for pasting a car with film, calculating the amount of film and its cost. Preparation of a car for pasting with vinyl, as well as methods of pasting a car with a film with your own hands.

This article is for people over 18 years old

Have you already turned 18?

Coating the body with a film is today the most widespread and popular type of car tuning, due to the low cost, efficiency and availability of this method for most car owners. A wide variety of PVC films of various kinds and colors, provides ample opportunities, to show imagination and make your car truly exclusive and stand out from the stream of cars on the road. There is nothing complicated in the process of pasting the car body, and if desired, these works can be done independently.

brand-detail-img-title "\u003e Camouflage Vinyl Car Wrap

What tools and materials will be required for pasting a car with film

First of all, it should be noted that pasting a car with a film with your own hands requires compulsory adherence to the technology of applying a film coating, as well as the availability of space for the production of these works, where you can create the necessary temperature conditions and absolute purity. The room should have moderate humidity, good lighting and a temperature of at least 20 ° C. To cover the car with vinyl film, you will need the following tools and materials:

the vinyl film itself of the selected type in the right amount;
scissors and a sharp stationery knife;
spray and soap solution prepared from water and detergent or in a ratio of 10: 1;
plastic or felt squeegee;
alcohol or solvent for degreasing the surface, white spirit is best suited for these purposes;
technical hair dryer;
masking tape;
dry rags made of soft, lint-free cloth;
primer 3M - a composition that enhances the adhesive properties of the adhesive layer of the film.

All this should be prepared in advance and be at hand when working.

brand-detail-img-title "\u003e Primer 3M

What film is better to paste over a car

Today there are two types of films for car body wrapping - vinyl and polyurethane. Vinyl-based film coverings come in a variety of styles and colors to transform your exterior design. Although they protect against ultraviolet radiation and minor damage, they are inferior in their protective properties to anti-gravel films made of polyurethane, which are only transparent and are used exclusively to protect the body.

Vinyl films are most often used for tuning and styling a car, which is explained not only by their variety, but also by their lower price.

According to the production method, such films are of two types:

calendered;
cast.

HEXIS Vinyl Films

Cast films are of higher quality and more durable, they are available in a wider range of types and colors, but are somewhat more expensive than calendered. Which film to choose for your car, everyone decides for himself. But, if you decide to do the pasting of the car with your own hands, it is better to choose a cast film of better quality, which is easier to work with. There are the following types of vinyl films (auto vinyl):

transparent and colored;
matte and glossy;
pearlescent and metallic films;
graphic films intended for drawing by digital printing methods;
textured films, with a surface stylized for various materials, which include a carbon-like film coating;
chameleon films, the color of which changes under different angles vision.

brand-detail-img-title "\u003e Chameleon Vinyl Film

The choice is really very large, and everything here depends on your taste, and on what effect you want to get by resorting to this kind of tuning. But, in any case, you need to buy a film famous brandsif you want it to easily fit on any body parts with complex surface relief and last as long as possible. The most popular and in demand in all countries of the world are the following brands:

3M Scotchprint (USA);
KPMF (UK);
Hexis (France);
ORACAL (Germany).

To determine how much film is needed for pasting, you need to know the area of \u200b\u200ball body elements on which it will be applied. It is quite difficult to carry out exactly such measurements, therefore, for an approximate calculation of the need for material and its cost, they use data verified in practice.

For the complete pasting of the car body, which is recommended when using auto vinyl, the following film consumption is taken, depending on the car class:

compact B-class cars - from 18 to 21 sq. m;
middle class cars (C-class) 23-24 m 2;
big family cars D-class 25-27 sq. M .;
business class cars (E-class) - from 27 to 30 square meters;
sports coupe S-class 30-34 m 2;
compact SUVs 25-30 sq. m;
large SUVs 34-37 m 2.

Vinyl rolls

It is best to buy auto vinyl in rolls 1.52 m wide, so that when gluing large body elements, you do not have to make joints.

Preparing the car for pasting with vinyl

In order for the film coating to last longer, before covering the car with film, the car must be properly prepared. This requires:

wash the car well with car shampoo and carefully inspect its paintwork for damage and persistent dirt;
if there are any remaining insect or bitumen stains, remove them with solvent or alcohol;
polish the body paintwork, to more smooth surface the adhesion of the adhesive layer of the film will be much stronger;
degrease complex body elements;
wipe the entire vehicle with a dry cloth.

brand-detail-img-title "\u003e Preparing the car for pasting with vinyl

Methods for pasting a car with film

There are two methods used today for film coating:

dry;
wet.

They are in many ways similar to each other and differ only in the technology of applying the film to the surface to be treated.

With the dry method, the film is immediately applied to the surface, without preliminary preparation of the latter. In the actions of the gluer, the maximum accuracy and confidence of movements must be present, because the adhesive layer will immediately stick to the body part being glued. The advantages of this method are:

saving time for work;
better adhesion;
no need for long-term drying of the car after applying the film.

Only experienced professionals who have filled their hands in the daily performance of such operations can afford to carry out pasting a car with a dry method.

brand-detail-img-title "\u003e Tool for car wrapping with film

The wet method involves applying a film coating to the surface treated with soapy water. This allows, in case of errors in the application of the film, to correct its position relative to the body part. This method is ideal for beginner gluers, or for those who decide to apply a film coating with their own hands.

If you decide to change the appearance of your car by applying auto vinyl, you must definitely decide how to cover the car with a film - the entire body or its individual parts. Today, many specialized car services offer various options when applying a film, including on individual parts:

rear and front bumper;
hood and roof;
car fenders;
doors and thresholds.

When using vinyl film, it is advisable to completely cover the entire body with it, because such material does not transmit ultraviolet light. And the paintwork of the body elements not covered with a film, by the time of its removal, can have time to fade in the sun, and will be noticeably different from the rest of the car.

brand-detail-img-title "\u003e When using vinyl film, it is advisable to cover the entire body with it

How to cover a car with a wet film yourself

The technology for wrapping a car with a wet method is quite simple. To do this work with your own hands, you must:

Mark the material, for which, without removing the backing, attach the film to each element of the body and mark the cutting line.
Cut the material according to the markings made. You need to perform work on a flat surface using a clerical knife and scissors, leaving a small supply of film on all sides.
Spray soapy solution evenly over the entire surface of the body part to be glued, without leaving dry places on it, in order to prevent the film from sticking to the body.
With the appropriate pattern down on a flat surface, gently remove the backing paper from the adhesive.
Try, as accurately as possible, to apply the film to the body element, pulling it slightly and fixing it at the upper corners. If this did not work out the first time, you need to raise the material and adjust its position relative to the boundaries of the body part.
Using a plastic squeegee, smooth out the film from the center to the edges, displacing the soap solution from under it.
After removing soapy water, repeat this procedure, heating the film with a technical hair dryer, and at the same time smoothing it from the center to the edges with a felt squeegee. Drying temperature should be in the range of 50-70 o C. This is done to activate the adhesive layer. Try not to overheat the film surface. The hair dryer must be held at an angle of 45 ° and no closer than 20 cm from the surface of the film.
Trim the edges of the film, leaving a margin of 5 mm, coat them with a primer and, bending, glue to the end surface of the part, smoothing with a plastic squeegee.
Wipe the glued surface with a dry cloth and leave the machine to dry at the same temperature for 24 hours.

It will take another 4-10 days for the film to adhere completely. During this period, you should not drive the car quickly and wash it.

Plastic squeegee 3M with felt strip for auto film

How to properly glue the film on a car with a dry method

The technology of dry car vinyl gluing differs from the wet method only in that the film, after removing the substrate, is applied to the dry surface of the body elements.

brand-detail-img-title "\u003e Dry Wrapping Machine Technology

This work is best done with an assistant, and when working, adhere to the following recommendations:

for a more accurate film overlay, you need to carefully mark the material and cut it with a small margin;
without removing the backing, try on the pattern, marking its edges on the body with masking tape;
remove the backing only on a flat surface, avoiding its gluing;
to start applying the film from the part of the part with a smaller radius of curvature, in order to slightly stretch the material during further operations;
in case of inaccurate application, slightly warm up the film and, removing it from the surface to be pasted, perform the operation more accurately.

Removing the vinyl from the machine

The application of film coatings to the car body is a popular type of styling, the popularity of which is also explained by the fact that at any time, the film can be easily removed without damage to the paintwork, returning the car to its previous state, or pasting it with another material.

To remove auto vinyl you need:

warm up the car in a warm room or in the sun;
heating the surface with a technical hairdryer to 70-80 ° C, pry off the film from one of the edges and start slowly pulling it up at an acute angle, moving towards the center of the coating;
reaching the middle, repeat the procedure, starting from the other side;
especially carefully remove the film from plastic partsso as not to overheat them and not deform;
if after removing the film, traces of the adhesive layer remain on the surface of the paintwork, remove them with a solvent or alcohol.

Subject to all technological requirements, the removal of auto vinyl from the car, as well as pasting the body, can be done with your own hands, without resorting to the services of specialized services.