Signaling Mongoose AMG 770 is designed to guard the doors of the car, its hood and trunk, the space inside the passenger compartment and the space in the immediate vicinity of your car. The car alarm uses a volume sensor with two zones of cantrol, for more information about control sensors, see the glossary of terms used in the description of car alarms. In addition, Mongoose AMG 770 prevents unauthorized engine starting, that is, it is equipped with an immobilizer.
The above functions can be implemented to a greater or lesser extent depending on the connected standard or additional security equipment.
To prevent unauthorized access to the system, the protection of the radio command code based on KeeLoq coding technology is provided. This technology successfully resists attempts to intercept car alarm codes using a code grabber. Also, this Mongoose alarm model is equipped with a built-in anti-scan function, which prohibits turning off the alarm by simply selecting random codes and a state memory function that does not allow disarming the armed alarm simply by removing and putting on the car battery terminal, since in this case the alarm will turn on and the engine will remain blocked.
Interruption and restoration of power supply when the protection is disabled will not trigger the alarm. This function is especially useful, for example, when repairing a car.
If the power was turned off when the alarm was in Valet mode (service mode, which can be found in the glossary of terms section), then its subsequent supply will return the alarm to the same state.
In order to avoid locking the keys inside the car, when the power is restored from the car battery, the state of the door locks does not change - a very useful function.
False alarms will be avoided by the function of bypassing the faulty zone, which will disable the faulty alarm sensor until the end of the arming cycle, if it triggers the alarm 10 times.
All other monitored zones and interlocks will remain enabled.
The programmable function of accounting for the delay of the interior light makes it possible to use the AMG 770 on all types of cars (this function is especially useful for cars manufactured before 1989).
To increase the security properties of the system and the convenience of using the car, the AMG 770 is equipped with additional channels with a software selection of options:
- to connect a pager or automatically close the windows during remote or automatic arming;
- to operate the electric trunk lock or other electrical device or to connect the Mongoose Communicator block, which allows you to control the Anti-HiJack function using the anti-hijacking card.
Comment: Mongoose AMG 770 also has a special entrance that allows you to implement the central locking function.
By purchasing a standard AMG 770 kit from our company, you get:
- Central control unit with complete installation kit.
- A two-level shock sensor, which is able to distinguish between weak and strong blows to the car body, which allows the alarm to react to them, either with a short siren trill or by triggering a full alarm.
- Two key fobs remote control.
- LED for indication of alarm modes, designed for installation in a car.
- Button emergency shutdown, the place of installation of which in the car you should choose together with your installer, so as to ensure sufficient secrecy of its location, on the one hand, and ease of use, on the other.
- Complete operating instructions for all AMG 770 modes.
To increase the security properties of the alarm, we advise you to purchase an additional two-level volume sensor capable of registering any movement both inside the car and in the immediate vicinity of it. This Mongoose AMG 770 alarm has a special input for connecting such a sensor.
Remote control alarm key fob.
The transmitter is a miniature radio transmitter powered by a standard 12 volt 23 A battery. The battery lasts for approximately one year of operation. A significant decrease in the range of receiving the transmitter commands by the system indicates the need to replace the battery. There are four control buttons and an indicator LED on the key fob. When you press any of the buttons, the transmitter generates and transmits a special coded command, which changes with each new press of the buttons, thus preventing the possibility of intercepting your alarm code by a code grabber.
Mongoose MAG 770 Alarm Command Table
| Command | Button 1 | Button 2 | Button 3 | Button 4 | Comment |
|---|---|---|---|---|---|
| Arming | * | Ignition off | |||
| Disarming | * | Ignition off | |||
| Locking doors | * | ||||
| Unlocking doors | * | Ignition on | |||
| Arming with disabled sensors | * | Ignition off | |||
| Silent arming. The passive immobilizer is disconnected. | * | Ignition off | |||
| Silent arming with disabled sensors | * | Ignition off | |||
| Silent disarming | * | Ignition off | |||
| enabling Panic mode | * 3 sec. | Ignition off | |||
| Search | * 3 sec. | Security mode or VALET. Ignition off | |||
| Additional channel: - unlocking the trunk - or control of another electrical device * |
* 3 sec. | ||||
| * 3 sec. | Ignition off | ||||
| VALET mode | * 3 sec. | The ignition is on. The passive immobilizer is disabled. | |||
| Security with the engine running | * 2 | * 1 | Ignition on | ||
| Disable passive immobilizer | Button number is set by programming | Ignition on | |||
* short press once
* 3 sec. press and hold the button pressed for at least 3 seconds
1 2 sequence of pressing buttons
* When the "pulse-latch" is turned on programmatically, the channel is activated by pressing button 3 for 3 seconds. Pressing button 3 again or turning on the ignition switches off the channel.
LED indication of the status of the anti-theft system.
Information Needed for Normal System Operation
PIN code.To increase the secrecy of alarm management in the AMG 770, it is possible to use a personal code (PIN code) to turn off the alarm, enter the programming mode for additional key fobs and custom functions, and disable the Anti-HiJack function.
The PIN code can be one or two digits and can have a value from 1 to 9 or 11 to 99 depending on the software setting. When the system is manufactured, a code equal to 1 is written into it, however, we recommend that after installing the system, set a different value for the PIN code (how to do this, read in the "Programming" section). This will allow you to secure your security system from unauthorized disarming.
The emergency shutdown button and the ignition key are used to enter the PIN code.
Emergency shutdown of the alarm.If the alarm key fob is missing or defective to disarm the system, you need to: open the door with the key, this will activate the alarm mode, get into the car, turn on the ignition and leave it in the on position.
If you have set a unique PIN code. Press the emergency stop button the number of times equal to the preset value of the PIN code, for example, if the PIN code is 8, then press the emergency stop button 8 times. After all, you need to turn off the ignition, if the code is entered correctly, the system will be disarmed.
If a two-digit PIN is set.Enter the first digit of the code as described above. Turn the ignition off and on again. Enter the second digit of the code in the same way as the first. Turn off the ignition, if the code is entered correctly, the system will be disarmed.
When installing a car alarm, it is important that the system ensures the safety not only of the car, but also of its owner.
Such important qualities are possessed by security systems from Mongoose, which delight users for a long time high quality and wide functionality.
ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe me? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!
Mongoose is gradually becoming a manufacturer of a wide range of security systems. And now she introduced car alarm mongoose amg 700, which almost instantly became very popular among car owners.
This system is ranked first by 2 factors: high specifications and affordable pricing policy. Breakdowns of the mongoose amg 700 super model are rare, which makes the number of positive reviews from motorists even greater.
What interesting functions and modes can the amg 700 system provide:
- a mode in which the system operates with minimal noise;
- alarm mode that does not use a siren, but only lighting elements and a user's pager;
- anti-Hi-Jack function, which sequentially disables all the main units of the unit, preventing theft of the car;
- even if the system is turned off by the user, the car doors remain closed;
- when an incorrect command is received, the system automatically goes into alarm mode.
The amg line does not stand still and new model mongoose amg 750 is already installed on many vehicles. The system is more elaborate, there are several interesting additions (for example, a more stylish and modern design).
Mongoose is focusing on quality without raising the price sky-high. The cost of the amg 750 is not much different from the previous model. The manufacturer makes every effort to make the user familiar with the functionality of this alarm as soon as possible. A reliable confirmation of this fact is clear and simple instructions for installing a car alarm, which comes with the security system.
- an anti-grabber is installed, which prevents the key fob from scanning the code;
- using a special PIN-code, when emergency, you can turn off the system;
- the "panic" mode will quickly get rid of unnecessary attention.
Technologies are developing very quickly, this is confirmed by the mongoose amg 770 security system, the functionality of which has become more productive. There are several new products that deserve attention of motorists, and the device interface has become more convenient.
This car alarm is not afraid of sudden changes in weather conditions - the system continues to function at a high technical level.
The developers have extended the life of the device, making it immune to temperature environment... In addition to the operating instructions, there is an installation manual in the kit, so each user can try a chance in self-installation of the system.
- when the engine is running, the security system continues to function;
- the system automatically warns the user about the intrusion into the car;
- in addition to recording alarms, the system also performs individual diagnostics.
Mongoose amg 800
Mongoose is gradually approaching the high-tech ideal. The mongoose amg 800 car alarm also received key fobs with a new, ergonomic design, which makes them very comfortable in the hand. The changes also affected the technical part: the system independently controls many functions of the car and minimizes the user's work. It is rightfully considered one of the best security systems both on the territory of Russia and abroad.
- a useful function has been installed that turns off the system for a short period of time;
- the system independently bypasses the failed area and continues to function properly;
- all the necessary information is displayed on the pager screen.
Mongoose amg 850 is a technologically accurate and durable car security system. At the same time, the alarm has a lower cost than earlier models.
The amg 850 has been at the forefront of the market for a long time.
The operation of the system is calculated as accurately as possible, there is all the necessary functionality. The car alarm will not only protect the car, but also save the life and health of the owner.
- activation of the security mode is almost silent;
- the alarm warns the car owner about a malfunction;
- there is a possibility of programming the duration of the operation of the central lock and window regulators;
- the installation provides additional relay blocking;
- simple wiring diagram.
Manual
Introduction
The Mongoose AMG 770 alarm system is designed to protect the doors of the car, its hood and trunk, the interior space and the space in the immediate vicinity of your car. In addition, the AMG 770 prevents unauthorized engine starting.
The above functions can be implemented to a greater or lesser extent depending on the connected standard or additional security equipment.
Please consult your installer.
To prevent unauthorized access to the system, radio command code protection based on KeeLoq coding technology. successfully resists attempts to intercept codes using a code grabber, built-in anti-scan function... prohibiting the shutdown of the alarm by simply selecting random codes and state memory function... which does not allow to neutralize the armed alarm simply by removing and putting on the terminal of the car battery, since in this case the alarm will turn on and the engine will be blocked.
Interruption and restoration of the power supply when the protection is disabled will not trigger the alarm, so as not to create difficulties, for example, during repairs.
If the power was turned off when the alarm was in Valet mode, then its subsequent supply will return the alarm to the same state.
To avoid locking the keys inside the car, when power is restored from the car battery, the state of the door locks does not change.
The function will help to avoid false alarms. bypass faulty zone... which will disable the faulty sensor until the end of the security cycle, if it has triggered the alarm 10 times.
All other monitored zones and interlocks will remain enabled.
The programmable cabin light delay function allows the AMG 770 to be used on all types of vehicles.
The AMG 770 is equipped with additional channels with software selection of options:
- to connect a pager or automatically close the windows during remote or automatic arming;
- to control the electric trunk lock or other electrical device, or to connect the Mongoose Communicator, which allows you to control the Anti Hi-jack function using the anti-hijack card.
With the AMG 770 standard kit you get:
- Central control unit with complete installation kit.
- A two-level shock sensor, which is able to distinguish between weak and strong blows to the car body, which allows the alarm to react to them, either with a short siren trill or by triggering a full alarm.
- Two remote controls.
- LED for indication of alarm modes, designed for installation in a car.
- The emergency stop button, the installation location of which in the car you should choose together with your installer, in such a way as to ensure sufficient secrecy of its location, on the one hand, and ease of use, on the other.
- Complete operating instructions for all AMG 770 modes.
If you want to improve the security properties of your alarm system, we advise you to purchase an additional two-level volume sensor capable of registering any movement both inside the car and in the immediate vicinity. The AMG 770 has a dedicated input for connecting such a sensor.
Remote control alarm key fob.
It is a miniature radio transmitter powered by a 12 volt battery (type 23 A), which lasts about 1 year of operation. A significant decrease in the range of receiving the transmitter commands by the system indicates the need to replace the battery. There are four control buttons and an indicator LED on the key fob. When you press any of the buttons, the transmitter generates and transmits a special coded command, which changes with each new press of the buttons, thus preventing the possibility of intercepting your alarm code by a code grabber.
Command table
Necessary information
PIN code.
To increase the secrecy of alarm control in the AMG 770, it is possible to use a personal code (PIN code) for emergency shutdown of the alarm, enter the programming mode for additional key fobs and custom functions, and disable the And Hi-Jack anti-hijack function.
The PIN code can be one or two digits and can have a value from 1 to 9 or 11 to 99 depending on the software setting. When the system is manufactured, a code equal to 1 is written into it, however, we recommend that after installing the system, set a different value for the PIN code (how to do this, read in the "Programming" section). This will allow you to secure your security system from unauthorized disarming.
The emergency shutdown button and the ignition key are used to enter the PIN code.
Emergency shutdown of the alarm.
If the alarm key fob is missing or defective to disarm the system, you need to: open the door with the key, this will activate the alarm mode, get into the car, turn on the ignition and leave it in the on position.
If you have set a unique PIN code, press the emergency shutdown button the number of times equal to the preset PIN code value and turn off the ignition. If the code is entered correctly, the system will be disarmed.
If a two-digit code is set, then after entering the first digit as described above, turn the ignition back on and also enter the second, then turn off the ignition. If the code is entered correctly, the system will be disarmed.
TERMS OF USE
Management of the main modes of protection
Arming.
To arm the alarm, press button 1 of the key fob with the ignition off, if all the doors, hood and trunk are closed, the siren will sound one beep and the lights will flash once. The system LED will start blinking slowly and the door locks will close (if the vehicle is equipped with locking actuators). If any of the doors, hood or trunk are not closed, three additional beeps will follow and the lights will flash three times.
Security.
In the security mode, the alarm monitors the state of all available limit switches for doors, hood, trunk, ignition on and the state of the shock sensor, as well as, if additionally installed, the volume sensor, etc. In addition, the engine start is blocked in the security mode. If any of the armed zones is violated, a 30 second alarm mode is activated.
Anxiety.
If the alarm mode is activated, the siren will sound, and the signal lights will flash for 30 seconds or until they are turned off by button 1 of the key fob.
When the warning zone of the shock sensor or the external zone of the additional sensor is triggered, a short siren trill will sound.
Disarming.
To disarm the alarm, press the button 1 of the key fob, the siren will sound 3 beeps, and the signal lights will flash twice. The LED will go off, the door locks will open (if the car is equipped with locking drives). If the alarm mode was activated during the security period, then four additional sound signals will follow when disarming.
Panic.
If, with the ignition off, press and hold for 3 seconds. button 1 will turn on the siren and warning lights. Pressing button 1 again turns off the mode. Enabling and disabling Panic does not change the state of the system, that is, it will remain armed, if it was in this mode, the doors will remain locked, if the system was disarmed and the door locks are open, arming and locking the doors will not occur ...
Silent arming and silent disarming.
When it is necessary to arm or disarm the alarm without sound confirmation, so as not to disturb others with the sounds of a siren, press button 2. Execution of commands in this case will be confirmed only by light signals. The rest of the modes are completely similar to arming and disarming with sound confirmation. When silently arming, the audible warning about unclosed doors, hood and trunk remains, so there is no danger that you will leave your car unlocked.
Arming with disabled sensors.
If, when arming, it becomes necessary to disable the interior sensors, for example, when it is necessary to leave passengers or animals in the vehicle, press button 3.
To arm with disabled sensors without sound confirmation, press button 4.
Security with a running engine.
In order to arm the car with the engine running (for example, when warming up), before pressing button 1, press the button 3 of the key fob, then the security mode with disabled sensors is activated, and the engine blocking will not be enabled. To turn off the security, press either the same combination of buttons or button 1 or 2. In addition, if the security has not been disarmed within 10 minutes or the ignition has been turned off, the engine blocking and full security mode are automatically turned on, but without relocking the doors.
NOTE: To avoid erroneous activation of the mode while the vehicle is in motion, its activation is allowed by the system only within 10 seconds after opening and closing the door with the ignition on, after these 10 seconds, the system will not enable the mode.
Using additional security functions
Automatic re-positioning (protection against accidental pressing).
If within 30 sec. after disarming, none of the doors, hood or trunk was opened, and the ignition was not turned on, the system will automatically return to the armed mode.
Two-step disarming.
If the alarm is triggered, then by pressing button 1 once, you only turn off the siren and warning lights (if the cause of the alarm has been eliminated, i.e., for example, an open door is closed or the shock sensor has stopped working). If the cause that caused the alarm persists, a second press of the button is required to turn it off. To completely disarm the system, press the button again after turning off the alarm.
Auto-arming.
The function can be enabled or disabled by programming.
If the function is enabled, after turning off the ignition, opening and closing the door, the warning lights will flash twice, the LED will flash quickly. If within 30 seconds after that all doors, as well as the hood and trunk remain closed, the alarm will arm without locking the doors.
Automatic door locking when the ignition is turned on.
5 seconds after turning on the ignition, they are automatically locked electric locks doors, the locks are immediately unlocked when the ignition is turned off. If during these 5 seconds any of the doors is open, then automatic locking will not occur to avoid locking the keys inside the car. The function can be disabled during installation.
Remote control of the central lock.
When the ignition is on, the car door locks can be locked or opened at any time by pressing buttons 1 or 2 on the key fob, respectively.
Passive immobilizer mode.
The mode is switched on and off by programming.
If the mode is enabled by software, then 1 minute after opening the door with the ignition off, the engine blocking will turn on. In this case, no other armed zones will be activated, the door locks will not be locked.
When the ignition is turned on within a minute after opening the door, the activation of the mode is canceled until the moment when the door is opened again with the ignition off.
The immobilizer mode will also automatically turn on if, after turning off the ignition, all doors remain closed for 10 minutes.
To turn off the immobilizer, press one of the four buttons of the key fob with the ignition on. Which one is chosen by programming. Factory setting is button 1.
If for some reason you cannot use the key fob to turn off the immobilizer, enter the PIN code, as in the case of an emergency shutdown.
If, when trying to disable the immobilizer, the wrong button is pressed, which is programmed to disable it, the alarm will immediately turn on, which can be disabled in the following ways:
- Press the desired key fob button.
- Enter PIN code.
- Turn off the ignition, arm and disarm the alarm.
In the first and second cases, the alarm and engine blocking will be disabled simultaneously. In the third case, the alarm will turn off, but the engine will be blocked until the desired button or entering the correct PIN code.
Having turned on the immobilizer mode programmatically, remember that:
- when the ignition is on and the immobilizer is armed, the system will not execute any remote control commands until the immobilizer is disarmed;
- if the immobilizer mode was already activated when the alarm was armed, then after disarming the engine blocking will remain, to disable it, press the key fob button that disables the immobilizer, or enter the PIN code.
Anti-Hi-Jack. Protection against robbery.
Your security system is equipped with a special anti-hijacking function Anti Hi-jack, which will be automatically activated when the ignition is turned on, as well as if any door is opened with the ignition on. Both modes can be switched on and off by programming independently of each other.
If the function is programmatically enabled and you are required to give the keys and leave the car, just follow the requirements of the burglars, Anti Hi-jack will trigger the alarm itself and make the burglars stop.
In order for the activation of Anti Hi-jack not to interfere with the movement of the car and you had the opportunity to safely turn it off, as well as not to create a dangerous situation on the road, regardless of the method of activation, the anti-theft procedure goes through the following stages until the moment the full alarms and engine blocking:
- 30 second pause to enter the shutdown code after turning on the ignition or opening the door with the ignition on. The system LED flashes slowly to remind you to enter a disable code.
- Warning mode. If you have not entered the disabling code during a 30 second pause, within the next 30 seconds the system will remind you of this by means of short beeps and flashing of the warning lights, the LED will blink rapidly.
- Alarm mode. At the end of stages 1 and 2, if the shutdown code has not been entered, the system goes into alarm mode: a full sound and light signaling... When turned on programmatically blocking mode with fault simulation, it will turn on when the alarm is triggered. In this case, the engine blocking will be carried out as follows: 1 second - blocking \u003d\u003e 5 seconds - pause \u003d\u003e 1 second - blocking \u003d\u003e 3 seconds - pause \u003d\u003e 1 second - blocking \u003d\u003e 2 seconds pause \u003d\u003e 1 second - blocking \u003d\u003e 2 seconds - pause, etc. The last cycle will be repeated until the ignition is turned off, after which the engine will be completely blocked and it will not be possible to start it until the Anti Hi-jack is completely turned off. If simulated malfunction lock is disabled by software, the engine will be locked immediately after the ignition is turned off. The alarm mode continues until the ignition is turned off and remains in the off position for 60 seconds. The entry of the trip code in alarm mode is blocked. If an incorrect code was entered twice during 1 or 2 stages, the system immediately goes into alarm mode, without waiting for the end of the stage. At the end of the alarm mode, the system goes into blocking mode.
- Lock mode: 3 minutes. In this mode, the sound signaling is disabled, however, the light signaling and blockings are preserved, the entry of the disconnecting code is blocked, the LED is off. After 3 minutes, the light signaling turns off, but all locks remain, the system goes into code standby mode.
- Code standby mode. The duration of the mode is 30 seconds. Turn on the ignition, the LED will start blinking with double flashes, enter the code. If the code is not entered within 30 seconds or is entered incorrectly, the system returns to alarm mode 3 and the whole cycle repeats.
Disabling Anti-Hi-Jack:
- During 30 second pause 1, as well as during warning mode 2, Anti-Hi-Jack can be disabled by entering the least significant bit of the emergency shutdown code. To do this, you can use a key fob or an emergency shutdown button. When using a key fob, you must:
- with the ignition on (the system LED blinks slowly with single flashes), press and hold button 3 of the remote control for three seconds;
- press button 2 of the remote control the number of times equal to the value of the least significant digit of the emergency shutdown code. When using the button, press it with the ignition on a number of times equal to the value of the least significant digit of the code.
If the code is entered correctly, after 5 seconds, Anti-Hi-Jack will turn off, the system will go into normal operation, confirming this with a double sound and light signal; if the code is incorrect, you can repeat the entry one more time.
- turn on the ignition (the system LED will start blinking with double flashes) press and hold button 3 of the key fob for three seconds;
- the system LED will flash quickly;
- press button 1 of the key fob the number of times equal to the value of the most significant digit of the emergency shutdown code, press button 2 of the key fob the number of times equal to the value of the least significant digit of the emergency shutdown code;
- if the code is entered correctly, after 5 seconds the Anti-Hi-Jack will turn off, the system will go into normal operation, confirming this with a double sound and light signal; if an incorrect code is entered, the system goes into alarm mode 3.
If you additionally installed the Mongoose Communicator module and programmatically enabled the anti-hijack card function, Anti-HI-Jack activation will be prohibited if the card is inside the car within 2 minutes after turning on the ignition or opening the door with the ignition on. If you need to turn off the ignition before the expiration of these 2 minutes, then first turn off the Anti-Hi-Jack with the emergency shutdown button the lowest digit of your PIN-code.
In order for Anti-Hi-Jack activation to become possible, in addition to the software activation of the function, it is necessary to set a two-digit emergency shutdown code for the system.
If you use Anti-Hi-Jack and passive immobilizer mode at the same time, then after turning on the ignition, you must first turn off the immobilizer, and then enter the code to disable Anti-Hi-Jack.
ATTENTION! If the Anti-Hi-Jack procedure is activated, the execution of any remote control commands by the system, except for entering the personal disable code and the command to disable the passive immobilizer, is blocked.
Anti-Hi-Jack Temporary Disable Modes
- If after disabling the anti-theft procedure by entering the emergency shutdown code (full or low level) none of the car doors opened, the ignition can be turned on and off an unlimited number of times, Anti-Hi-Jack will not be activated. When the door is opened for the first time, the mode is disabled.
- If, to disable the anti-theft procedure, enter the disabling code from the key fob when open door, Anti-Hi-Jack activation when the door is opened will be canceled until the next ignition off and on.
To temporarily prevent activation of Anti-Hi-Jack, you can also use Valet mode.
Diagnostic functions
Malfunction warning.
If, when arming, any door, hood or trunk is not closed, you will hear 3 additional beeps instead of one and the lights will flash 3 times.
Memory of alarms.
If the alarm is triggered during the armed period, when disarming, you will hear four beeps instead of two and the lights will also flash four times. After switching on the ignition, the system will report the cause of the alarm with three series of LED flashes:
Number of flashes in a burst
Special service modes
Accounting for the delay of the cabin light.
The mode is activated by programming.
If the car has a cabin light delay function, and the cabin light delay metering mode is programmatically enabled, the door limit switches will be armed only after the light in the cabin goes out. There is no notification about not closed doors when arming in this mode.
Vehicle search.
If during the period when the alarm is armed or is in Valet-mode for 3 seconds. press button 2, the siren will beep once, and the lights will flash six times, indicating the place of the car in the parking lot.
Valet mode.
In this mode, all security functions of the system are disabled. You can turn it on, for example, when you give the car to the service, and then you do not have to leave your alarm key fob there. This is an absolute guarantee against unauthorized recording of new key fobs into the memory of your security system.
To enable the mode, it is necessary with the protection disabled and the ignition on for 3 seconds. press button 4 of the key fob, the signal lights will blink three times, the system LED will light up continuously. Valet mode retains the ability to remotely control the central lock and additional channels. Pressing button 4 again with the ignition on returns the system to normal operation, which is indicated by three beeps.
Keyfob programming.
- Switch on the ignition.
- Enter the first (or only) digit of your PIN code by pressing the emergency shutdown button the corresponding number of times.
- Switch the ignition off and back on. If a 2-digit PIN has been set, enter the second digit with the emergency shutdown button.
- When you have finished entering the code, turn the ignition off and on again. If the code is entered correctly, the system is double sound signal will inform you about entering the keyfob programming mode.
- Press button 1 of the programmable keyfob. A short beep will confirm the entry of the keyfob code into the system memory.
- To exit the keyfob programming mode, turn off the ignition and press the emergency shutdown button or wait 15 seconds. The system will signal the exit from the mode with a double beep.
Function programming.
In order to change the PIN-code value, erase from the system memory the key fobs you do not need, enable or disable Anti Hi-Jack, set a new value for programmable functions, you must first program the key fobs described above, and for this you can use a key fob that is already known system. Then follow this procedure:
- After finishing programming the key fobs, turn on the ignition.
- Enter the first digit of the program switch number by pressing the emergency stop button a number of times equal to this digit.
- Switch the ignition off, then on and enter the second digit of the program switch number with the emergency shutdown button.
- To turn on the function, press button 1 of the remote control, to turn off - button 2.
- If it is necessary to change the value of other functions, turn off and on the ignition no later than 10 seconds and repeat the procedure from step 2. At the end of programming, turn off the ignition and press the emergency stop button, the system will confirm the exit from the mode with a double beep.
