We are going to talk about how to change the rear brake pads for a KIA LED of the 1st sample.
Original part number: 58302-1HA00; also equivalent in article SP 1187.
How to replace brake pads manually using a minimum of tools. To perform this operation, you do not need any special qualifications, all you need is to devote twenty minutes of your time.
Inventory
Are we going to use fourteen and seventeen millimeter wrenches, a hammer or ratchet extension with a twenty-two head?
Replacing the rear brake pads on the Kia Sid photo report
Let's get started
By removing rear wheel, our attention will be presented to the brake disc and caliper, it is attached to the caliper on two bolts (the rubber bands of the guides are also located in the same place).
Let's start with the fact that, take a wrench for fourteen, or a ratchet with a similar head, and rotate the top bolt.
After removing it, we need to lower the caliper down, by this action we release the pads. And now half is done.
We can remove the old rear pads either manually or with a screwdriver (the main thing is not to damage the disc). After that, you can install new ones in place.
Then we need a hammer or, in our situation, an extension cord with a large head (22), as well as an old block. We put the shoe on the piston, and we can rest against the head with the extension, after that we press. And do not forget to hold the caliper with your hand a little, this will help us not to damage the guide.
We will press the piston until the caliper is free to put on new pads. The front pads are as easy to replace as the rear pads. At the end of this procedure, we install everything back.
Check the status brake pads at every service.
The brake pads must be replaced when the linings are worn out (the minimum permissible thickness of the friction linings is 2.0 mm), when the linings are not firmly connected to the base, the working surfaces are oiled, there are deep grooves or chips.
On inner pads rear brakes wear indicators are installed. When the minimum lining thickness is reached, the wear indicator comes into contact with the brake disc during braking, causing a squeak, signaling the onset of the limit wear of the brake pads.
A WARNING
Replace the rear brake pads only with a set of 4. (two on each side). Check the level before replacing the brake pads. brake fluid in the tank of the main brake cylinder... If the level is close to the upper mark, it is necessary to pump out part of the fluid, since after replacing worn out pads with new ones, the level will rise.
You will need: a "14" wrench, a flat-blade screwdriver.
1. Remove the rear wheel.
3.. .and lift the caliper upwards with the outer brake pad.
4. Remove the outer and inner brake pads from the guide.
USEFUL ADVICE
Whenever you replace the brake pads, always check the condition of the protective rubber covers guide pins, as well as the ease of movement of the caliper relative to the brake pad guide. If movement is difficult, lubricate the guide pin and its boot with grease.
5. Using pliers, press down the cylinder piston.
6. Install the retaining springs, brake pads, and other removed parts in the reverse order of removal.
7. Replace the brake pads in the same way. brake mechanism right wheel.
8. Check and, if necessary, restore the level of the brake fluid in the reservoir of the master brake cylinder.
Let's show how with our own hands in the car Kia ceed 2011 onwards replace rear brake pads, discs and caliper guides. Remove the wheel, unscrew the caliper (bolts 14), take it to the side. We remove the brake pads. Remove the bracket using a 14 head and a spanner wrench. After that, we check the guides, in our case one walks normally, and the other does not, a replacement is necessary.
The brake discs have a special window:
There is a mechanism for converging and spreading the pads, the so-called spacer bar. In order to bring the pads together, we take a good sturdy screwdriver, twist down with clinging movements, to the end. In the next step, we will need an impact screwdriver to unscrew the fastening screws:
Remove the brake disc with a hammer. Often brake discs sour on the hub, so before installation, be sure to lubricate all "seating" surfaces copper grease so that next time you can take it off without any problems.
Rear video replacement brake discs and pads in the KIA Ceed:
Backup video how to replace rear brake discs and pads in KIA Sid:
The brake disc on this machine acts as a "drum" for the parking brake.
On the Kia cars Sid, as in most non-sporting cars, has only one hydraulic brake cylinder for each wheel. If you own a sports car, there may be two of them, located on either side of the disc. The task of the cylinder is to create pressure on the inner shoe, pressing the outer one is forced, since its structural device is such that there is no other place left. Due to the fact that the main work falls on the inner pad, its wear is traditionally stronger in comparison with the outer one.
With this in mind, don't be surprised if the outer pad is much less worn out. It is also important to know that the service life of the pads is rear wheels traditionally, 1.5-2 times more than the front ones, which withstand the main load during braking. Relatively even wear can only occur when your driving style is approaching retirement. However, in this case, the brake pads will serve you not 30, but all 60, or even 70 thousand kilometers. To install the pads correctly, remember that the wear sensor (the so-called "squeak") is installed only on the inner pad, since its wear is faster. But remember that there are times when such sensors simply break off without having time to inform the owner of the car about the wear of the pads. Do not rely on it, and check the degree of wear of the brake pads yourself, when going through seasonal maintenance, for example.
First of all, let us outline the safety rules when examining the condition of brake pads:
- Always check their condition during each MOT. Also check with the experts if the Kia Sid parking brake pads need to be replaced
- Do not use friction pads with a thickness of two or less millimeters, but rather replace them before this dangerous milestone.
- Replace the Kia Sid pads if you see chipping, deep grooves, a large oily layer or a weak connection of the pads to their base on their surface
- All brake pads "KIA Sid" are equipped with wear indicators, which, when the pads are thinned to an acceptable minimum, begin to touch the brake disc during braking, which leads to a clearly audible squeak. If you hear such a sharp creak, replace the brake pads immediately, otherwise any of your trip may result in a serious accident.
- Replace brake pads exclusively in a comprehensive manner. So, for example, install 4 pieces on the front brakes at once - 2 per wheel
- Before replacing the pads, measure the level of the brake fluid poured into the reservoir of the main brake cylinder. If its level is near the upper mark, then drain it a little, because always after installing new pads, its level will rise
- Remember to check the movement of the caliper along the brake shoe guide. If it is difficult to move, lubricate its guide pins with grease.
Kia See'd front pad replacement procedure
- Disassemble the front wheel
- Lift the caliper up
- Using a 12 wrench, remove the lower bolt of the bracket body. To facilitate this procedure, hold the guide pin of the bracket with a hex wrench
- Remove the brake pads from the guide - inner and outer
- Remove a pair of retaining springs from the guide shoes
- Install in reverse order guide brake pads with fixing springs, and then all other parts. To prevent the guide pin of the caliper from unscrewing during operation, an anaerobic lock must be applied to its thread in advance.
- Check the brake fluid level and replenish if necessary.
The procedure for replacing the rear pads "KIA Sid"
- Disassemble the rear wheel
- Then you should remove from the guide a pair of brake pads - inner and outer
- Press down the cylinder piston with pliers
- Using a 14 wrench, unscrew the lower bolt that secures the caliper. To better perform this procedure, lift it up through the top bolt
- Remove the old pads, but carefully clean the guides before installing new ones.
- And only after that, in the reverse order, install the brake pads with fixing springs and all other parts.
- Finally, remember to check the brake fluid level in the reservoir and top up if the level is insufficient.
The replacement of the Kia Sid brake pads is over, but do not rush to immediately go somewhere in your car, especially since you do not need to go to busy city streets and high-speed country roads. There is a chance that the first time you brake hard, the new brake pads will work with very low efficiency, even if you have installed branded and not analog parts. After all, not only the pads wear out, but also the brake discs. And it happens that the new brake pads only come into contact with the edges of the old, already worn out brake discs.
Therefore, in order to avoid such an unpleasant incident, choose some quiet place and smoothly brake the car on it several times. This is necessary so that the pads rub against the brake discs with their entire surface, and you can evaluate how effectively the new pads brake.
And in the future, at least the first hundred kilometers traveled, avoid sudden braking. The fact is that with strong heating at the pads that have not yet worked in the brake discs, the top layer of their linings can burn, as a result of which the new brake pads will not be able to demonstrate their maximum efficiency to you for a long time.
The procedure for replacing the parking brake pads, rear and front Kia wheels Sid. Subtleties and nuances self replacement pad Kia ceed.
Replacing brake pads Kia Sid
On Kia Sid cars, as on most non-sporting cars, there is only one hydraulic brake cylinder for each wheel. Oil change in automatic transmission KIA SID 2007 Replacement rear brake pads Nissan Bluebird photo report If you own a sports car, there may be two of them, located on both sides of the disc. The task of the cylinder is to create pressure on the inner shoe, pressing the outer one is forced, since its structural device is such that there is no other place left. Due to the fact that the main work falls on the inner pad, its wear is traditionally stronger in comparison with the outer one.
With this in mind, don't be surprised if the outer pad is much less worn out. Kia seed replacement lamps fog lamp video Replacing the rear brake pads Ford fusion It is also important to know that the service life of the pads on the rear wheels is traditionally 1.5-2 times longer than the front ones, which withstand the main load during braking. Relatively even wear can only occur when your driving style is approaching retirement. However, in this case, the brake pads will serve you not 30, but all 60, or even 70 thousand kilometers. Replacing a fog lamp bulb Kia led 2013 Sirius Avto To install the pads correctly, remember that the wear sensor (the so-called "squeak") is installed only on the inner pad, as its wear is faster. Replacement rear pads and brake discs Lancer 9 Mitsubishi. Replacing the master cylinder clutch Kia Sid - Kia Ceed But remember that there are times when such sensors simply break off without having time to inform the car owner about the wear of the pads. Replacing the rear brake pad and brake drum Kia spectra... Replacement rear brake pads on Mitsubishi car Lancer IX is the same for all 3 types of engine, therefore the catalog presented below. Do not rely on it, and check the degree of wear of the brake pads yourself, when going through seasonal maintenance, for example.
First of all, let us outline the safety rules when examining the condition of brake pads:
- Always check their condition during each MOT. Also check with the experts if the Kia Sid parking brake pads need to be replaced
- Do not use friction pads with a thickness of two or less millimeters, but rather replace them before this dangerous milestone.
- Replace the Kia Sid pads if you see chipping, deep grooves, a large oily layer or a weak connection of the pads to their base on their surface
- All brake pads "KIA Sid" are equipped with wear indicators, which, when the pads are thinned to an acceptable minimum, begin to touch the brake disc during braking, which leads to a clearly audible squeak. If you hear such a sharp creak, replace the brake pads immediately, otherwise any of your trip may result in a serious accident.
- Replace brake pads exclusively in a comprehensive manner. Choice Replacement oil in the box machine KIA Sid So, for example, install 4 pieces at once on the front brakes - 2 per wheel
- Before replacing the pads, measure the level of the brake fluid poured into the reservoir of the main brake cylinder. Replacement rear brake pad Volvo xc60 2013 + - If its level is near the upper mark, then drain it a little, because always after installing new pads, its level will increase
- Remember to check the movement of the caliper along the brake shoe guide. Replacing Kia Ceed lamps with your own hands If it is difficult to move, lubricate its guide pins with grease.
Similar news
Replacement of rear brake pads KIA LED / Kia Ceed / Lubrication of calipers
This video was processed in YouTube Video Editor ()
Replacing the rear brake pads KIA RIO 2013 in detail and clearly
In this video I will show you how replace rear brake pads! Everything is very simple and fast. You don't have to pay your uncles ...
Similar news
Kia See'd front pad replacement procedure
- Disassemble the front wheel
- Lift the caliper up
- Using a 12 wrench, remove the lower bolt of the bracket body. Replacing the front and rear brake pads on the Skoda Octavia A5 To facilitate this procedure, hold the guide pin of the caliper with a hex wrench
- Remove the brake pads from the guide - inner and outer
- Remove a pair of retaining springs from the guide shoes
- Install in the reverse order the brake pads with retaining springs, and then all other parts. News Kia LED replacing the fog lamp bulb video Kia LED replacing the fan-shaped washer nozzle - To prevent the caliper guides from unscrewing during operation, an anaerobic retainer should be applied to its threads in advance
- Check the brake fluid level and replenish if necessary.
The procedure for replacing the rear pads "KIA Sid"
- Disassemble the rear wheel
- Then you should remove from the guide a pair of brake pads - inner and outer
- Press down the cylinder piston with pliers
- Using a 14 wrench, unscrew the lower bolt that secures the caliper. To better perform this procedure, lift it up through the top bolt
- Remove the old pads, but carefully clean the guides before installing new ones.
- And only after that, in the reverse order, install the brake pads with fixing springs and all other parts.
- Finally, remember to check the brake fluid level in the reservoir and top up if the level is insufficient.
Replacing the brake pad Kia Sid is over, but do not rush to immediately go somewhere in your car, especially since you do not need to go to busy city streets and high-speed country roads. Replacing the rear pads and brake discs Lancer 9. There is a possibility that at the first hard braking, the new brake pads will work with very low efficiency, even if you have installed original and not analog parts. After all, not only the pads wear out, but also the brake discs. And it happens that the new brake pads only come into contact with the edges of the old, already worn out brake discs. Change air filter BMW X5 E70, E53, F15 If the car has become more sluggish on the move, has lost power and there is a feeling that the engine is "suffocating", mainly, the problem lies in the deterioration of the property by another decrease in the volume of air entering it. It is quite easy to avoid such an obstacle - for this purpose, at times you ...
