This common problem has a number of different reasons. While working with the device, you can meet both with obvious problems, the signs of which are clearly traced and with asymptomatic cases. The first option is the most simple from the problem of finding a problem. If the trimmer does not gain momentum, but there are no clear signs of breakdowns, it will be necessary to sequentially check the most typical cases of malfunctions, and when the cause is detected - to eliminate it.

The problem when the motocos does not gain momentum, is mainly found petrol aggregates. This suffers from technology different modelsFor example, Husqvarna, Champion, Stihl.

With high-quality products such problems are less common than with cheap from unknown manufacturers.

Part constructive elementsWith which problems may be related to visual inspection, and to check the operation of the rest of the nodes will need to disassemble the motocos.

Low Quality Fuel Application

The trimmer does not develop revisions if the low-quality fuel is charged. For this reason, the engine can do not start or work "jerks", Changing the speed of rotation of the knife or fishing line.

To independently determine the quality of gasoline used, perform the following actions.

1. Special key remove candles.
2. Inspect their working contacts for the presence of color of the color of the red brick: if it is, then the fuel used contains significant inclusions of the additives.

Candles generally often act as indicators to determine the problems with the combustion chamber of the gasoline engine, because they can be quickly removed and inspect.

Spark plug

When the weld is detected, it is necessary to drain the fuel filled into the tank and replace it with high quality. The benzocos used should be refilled only by those brands of gasoline, which are indicated by manufacturers in the instruction manual. Also be sure to clear candles from plaque Before installing in place.

Air or fuel filter pollution

The next reason for the reduction of the number of revolutions on the trimmer is to pollute its air or fuel filters. In the first case, the problem lies in the fact that the fuel and air mixture entering the combustion chamber it is not sufficiently saturated with oxygenAs a result, gasoline burns not all. It does not allow the maximum power to develop the motocos.

Air filter

In order to check whether it is really to blame air filter, It is necessary to remove it (pre-promoting the cover for this) and turn on the benzokos. If it works fine, then instead of the scored filter element, you must insert a new one.

If the situation has not changed after the proceeds done, then you need to pay attention to the fuel filter. The essence of the problem is similar to the previous case, only instead of lack of oxygen there is little gasoline for normal work Devices. The elimination of this problem is also made by a simple replacement of the filter element. Filters for air and fuel are inexpensive. Change them is easy independently, and all the work does not take much time.

It should be borne in mind that without fuel filter Operate the trimmer is prohibited by the instruction, otherwise it will be necessary to repair the piston node after a short time.

Ignition Candle Problems

With the permanent operation of the benzokos, the ignition candles is contaminated and wear out. To check it, they are removed and inspected for nagar. The problem can be eliminated in two ways: if possible, restore the old candle, or just install a new one in its place.

In the first case, they act like this:

• twisted and wipe the candle from the fuel;
• dry it without calcination;
• using the outfield or fine sandpaper, remove the CAG Candles and check the gap between the electrodes (must be 1 mm);
• collect trimmer;
• plant by Benzokos.

If the candle does not give a spark after reducing manipulations at the desired distance between the electrodes, it will be necessary to check connection quality Elements of the electrical circuit of the device. When with wires full order, you will need to unambiguously install a new item.

Candle replacement is a simple process that costs cheaply, and if you manage to restore old, then in general for free. You will need only a candle wrench and a feet.

If regular rapid pollution and wear of candles occurs, then you need to look for the problem of these abnormal phenomena deeper.

Motor problems

If everything is in order with fuel, filters and candle, the next source can be a gasoline engine. It can have the following mechanical breakdowns:

• carboretor-related malfunctions;
• problems with engine drive mechanism.

In the carburetor department there is a small cable. He can save and lead to the problem under consideration. Therefore, dealing with the carburetor, you should first check cable state, and if necessary, tighten (but not to the limit). The main thing is not to overdo it with the stretch so that under load it has not cracked.

Cables in the carburetor

After you need to check carburetor operating settingsthat must comply with the parameters given in the instructions. If they are installed correctly, but there is no needed effect, you should disassemble the item, rinse, clean, blow all its strokes and collect back. The carburetor itself should be without mechanical damage.

If it is impossible to independently restore the operation of the carburetor, it is better to replace it with new detail Or resort to the services of professionals.

In the case when adjustment or replacement of the carburetor does not give the desired result, it is necessary to clean the drive mechanism and lubricate the cable located inside it.

Carburetor

Motor-related malfunctions can be eliminated with their own hands in the presence of the required skills, but it is better to use the services of the service center for this. Its specialists will conduct a comprehensive diagnosis of trimmer and will establish the exact cause of the incidence of revolutions.

Failure in the fuel circulation system

Violation of normal fuel circulation on the trimmer also leads to the fact that the benzokos does not gain working turnover. This may be caused by such basic reasons:

• air suction, which is caused by the presence of cracks on the hoses;
• clogging of the gasoline pump that happened due to application embossed fuel either due to the formation of precipitate at the bottom of the tank and entering it into the system;
• pollution of the muffler or catalyst.

Alone to eliminate the considered troubleshooting needs to be done:

• go through fuel pumps, removing contamination;
• replace the tubes and hoses for which the fuel circulates;
• clean the muffler and the mesh on it;
• put a new catalyst that it will be expensive due to the content of precious metals in it.

All operational troubleshooting work in the fuel circulation system can be performed independently. But it should be taken carefully, so as not to lose the items, or after assembling the braids there is no "extra".

Possible causes of malfunction in electrical braids

When operating the trimmer on which electrical engine, There are also problems with a set of revolutions. But they are caused by completely different problems, compared with fuel braids. The electric motor does not develop the required speed of rotation in such cases:

• if the voltage operating in the supply network is below the nominal value for the electric motor by more than 10%;
• when problems in the smooth start system (if this unit is installed);
• when there are problems with the brush knot;

Brush knot electrocos

• in the event of burning engine windings;
• if the rotating parts are subdivided.

In order to exclude tension problem, It is required by a multimeter or tester to check its magnitude in the outlet, from which the power of the electrocouples is taken. If it is less than the minimum permissible value, then it will take all the electrical appliances to be turned off to enhance it or install the stabilizer.

The prerequisite necessary for the normal operation of the trimmer is the use of an extension cord with a cross section, corresponding to the power of the braid engine.

For repair block of smooth start You will need to have the appropriate knowledge in electronics, so it is better to contact the service center. They will be determined with its maintainability or the need to replace. You can independently check the button or find the block diagram and try to figure it out.

Block smooth start

Brushes Can wear, as a result, contact will disappear, which leads to the electric motor stops. Brushes replace easy. The features of the process are determined by the model used motocos. Also, you will also need to clean all the contacting surfaces.

When mooring windingsIf you continue to mow grass or shrub, the electric motor will quickly burn. This will be accompanied by the appearance of the smell of Gary, up to the melting of individual details. It will be needed to replace the electric motor.

Twinking rotating parts Comes for various reasons. To identify and eliminate them, you will need to sort out the drive unit. There are models that the number of revolutions is automatically regulated depending on the load, increasing when it increases - they have idling The speed of rotation drops.

The video shows an action algorithm to identify the most common causes, according to which the trimmer does not gain the required turnover:

Conclusion

In the market is presented wide choose Trimmers from various manufacturers. For them are characteristic general reasonswhy the turns are falling. Also each unit is equipped with instruction manual. In it, the corresponding section contains the necessary recommendations on this issue regarding the model used.

If in the process independent elimination The problem of a positive result could not be achieved, it is better to seek help from specialists. It should also be involved in solving the problem of professionals in the absence of minimal experience and skills in such a matter to not harm. The most complex node is the engine. Work with it is permissible only experimental masters. When motocos is on warranty service , optimal option - It is to contact the service center where the diagnosis and repair of equipment will be carried out.

What to do if a benzotrimmer is not gaining momentum?

If you once acquired a trimmer working with gasoline, you probably had to deal with the problem of including trimmer, as well as with such a problem as a benzotrimmer gaining momentum.

That is why this article was created.

So what to do if the trimmer that works for you is no longer the first year, suddenly he stops recruiting turns, and the motor simply stalls? In this case, we will consider a number of problems associated with a motor stop.

Motor can stall under different circumstances. Benzokos does not develop turnover, cause. | Funnycat.tv. Sometimes the cause of incorrect work of a trimmer running from gasoline is to clog the air filter.

It is the filter that is one of the most important reasons why work may stop gasoline Trimmer.

It often gets different garbage, there are dust particles, which also clog the filter, so it needs to be cleaned and washed every month, and maybe more often, it all depends on what power has gasoline trimmer, as well as how often you use this device.

Benzokos not develops Turns. One cause

Chinese benzokos Analog Husqvarna does not develop the reasance It turned out very simple (watch in the video)

Motokos is not gaining turns, cause of malfunction and elimination of it

Description.

If the filter operations have done, you have done, but the work of a trimmer running from gasoline remained the same, the benzotrimmer is not gaining momentum what to do?

Then you should try to extract a filter from the device in order to ensure the so-called "relief" of the trimmer. Benzokos does not develop turnover, cause. | Dovi. Should help.

The next and pretty problematic problem when working with a gasoline trimmer is that it just stalls, and does not attach any signs of life.

In this case, the problem may consist of:

The latter and most common cause of the breakdown of the gasoline trimmer is that the cable, which is located in the carburetor department, simply slept.

Therefore, make sure that it is well stretched, but not up to the limit, otherwise, with too much load on the gasoline trimmer, this small cable can crack and then you will definitely have to contact the service center, and then throw a lot of money to the wind.

Read the same way

Why does not get the trimmer gasoline? Causes and their elimination in our time, the gasoline trimmer has acquired the status of the 1st of the main tools in the Arsenal of Dachnikov. And such a situation is logical, because the motorized braid allows enough to rapidly lead the household plot in order. But from time to time it happens that the trimmer will not start ...

SHTENLI DEMON BLACK PRO S SHTENLI DEMON BLACK PROTECT WILL BENZOKOSY SHTENLI DEMON BLACK PRO S on the Agrotema.by website Assembly and launching SHTENLI DEMON BLACK PRODUCTION ROLLER Carefully shows the right assembly and 1st launch of the benzokosy / Trimmer SHTENLI DEMON Black Pro 3500 ....

Benzokos is one of the main tools of the dacket used to quickly bring the land plot in order. Acquire this tool to mowing herbs on the homeland territory and owners of private houses. The period of active use of benzokos and electric trimmers falls on summer period. Before exploiting the operation, the tool is driven into a working status: lubricated parts, the cutting headset changes, poured into the tank fuel mixture. If the engine does not start at all or quickly stalls, without dialing a sufficient number of revolutions, then you have to look for causes and troubleshoot identified. To carry out the repairs of the benzokos with their own hands, it is necessary to understand its device and the principle of operation of the main nodes. This information can be found in the instruction manual, which the manufacturer applies to garden equipment at mandatory. Check the availability of such a guide when buying chainsaws. The import tool must be accompanied by instructions written in Russian.

Long tubular rod is attached to the gearbox two-stroke engine internal combustion. Inside the rod passes the shaft transmitting torque from gasoline motor to the cutting mechanism. The fishing line or knives rotate with a frequency of 10,000 to 13,000 revolutions per minute. In the protective case of the gearbox, the presence of holes in which a lubricant is entered using a syringe. For ease of use of the tool, the manufacturer equips it with a special adjustable belt dropped over the shoulder.

A cutting headset is attached to the benzokos:

• Lesk, the thickness of which varies from 1.6 to 3 mm, is located in the trimmer head. During the mowing of grass, the line is subjected to wear. The replacement of the fishing line is performed quickly and easily in two ways: by winding the line of the same diameter on the bobbin or by installing a new coil with the already wound fishing.
• Steel knives with double-sided sharpening benzocosa for cleansing a plot from bunign, small shrubs, rigid grass. Knives differ in the form, as well as the number of cutting surfaces.

On the U-shaped, D-shaped or T-shaped handle attached to the rod, there are benzocosa control levers. The cutting mechanism is fenced with a special casing. Household motocos are refilled with a mixture prepared from gasoline and oil, which is poured into fuel tank. The device of semi-professional and household motocos equipped with four-time gasoline engine, slightly different. The refueling scheme is also different: the oil is poured into the crankcase, and gasoline is in the tank.

The diedy piece of the fishing line is so that one end is longer than 15 cm. The loop we get into the slot exhibiting on the coil, and begin to wind in the direction indicated by the arrow

What to do if the engine does not start?

If you fail to start the benzokos, then the first thing you need to check the availability of fuel in the tank and its quality. To refill tools, it is recommended to use quality gasolineacquired by petrol stations, whose mark should be not lower than AI-92. Savings on cheap fuels can lead to a breakdown of a piston-piston group, for the repair of which one third from the value of the motocos itself can leave. It is equally important and correctly prepare the fuel mixture of gasoline and oil. The proportional ratio of these mixture components is indicated by the manufacturer in the manual. You should not prepare the fuel mixture in large volumes, since it is lost with its own properties. It is better to use a freshly prepared mixture.

When preparing a fuel mixture, oil is poured into gasoline using a medical syringe that allows you to accurately comply with the necessary proportion of components

Pollution of the fuel filter in the tank may also prevent the operation of the gas station engine. Therefore, if there are problems with starting a motor, check the filter status. If necessary, make a replacement of the filter. It is forbidden to leave the incoming nozzle without a fuel filter.

Also in checks the air filter needs. When contamination, the part is removed in field conditions washed in gasoline and put in place. At the cottage or at home, the filter can be washed in water using detergents. After that, the filter is rinsed, pressed and dried. The dried filter is wetted by a small amount of oil used to prepare the fuel mixture. Excess oils are removed by compressing the filter with their hands. Then the item is installed in place. The removed cover is placed back and secured with screws.

Air filter, washed in the fuel mixture, pressed and dried, installed in the place in the plastic housing and closed with a lid

How to do this procedure You can watch in more detail on the video:

If all of the above procedures are carried out, and the engine does not start, then adjust its speed at idle, screwing the carburetor screw. In the video posted at the beginning of the article, attention is paid to this issue.

So, in order:

1. Put the tool on the side so that the air filter is at the top. With this location, the chainsaws are ensured by the fuel mixture in exactly the bottom of the carburetor. From the first attempt, a motor will be headed if you're before starting to remove the air filter and fill in the carburetor a few drops of the mixture, then install dismantled parts into place. The method is checked in practice.
2. If the first board does not give results, then, most likely, the problem in the ignition candle. In this case, unscrew the candle and check its performance, as well as dry the combustion chamber. A candle that does not feed signs of life, replace the new one.
3. If the ignition candle is in good condition, the filters are clean and the fuel mixture is fresh, you can use the universal engine to start the engine. Close the carburetor air damper and pull the starter knob once. Then open the damper and pull the starter 2-3 times. Repeat the procedure from three to five times. The engine will necessarily start.

Some with such a force twitch the handle, which you have to repair the starter of the benzokos with their own hands. This is only possible in the case of a rush of the cable or breakage of the cable handle. In other cases it is recommended to replace the starter. This node is sold assembly.

How to replace the ignition candle?

The order of work is as follows:

• Stop the engine and wait until it cools.
• Disconnect the high-voltage wire from the spark plug.
• Unscrew the item using a special key.
• Inspect the ignition candle for replacement. The item changes if it is faulty, is strongly contaminated, has a crack on the housing.
• Check the gap between the electrodes. Its value should be 0.6 mm.
• A new candle inserted into the engine, tighten the key.
• Spend the installation of high-voltage wire to the central electrode of the candle.

As you can see, there is nothing superpost in this procedure.

The new ignition candle for the two-stroke engine of the internal combustion of gasoline spit is installed instead of an old detail, failed

Why is Benzokos stall after launch?

After starting, the motor can sall in the event that the carburetor is incorrectly configured or it has occurred. What features can you understand that the reason really lies in this? It is very simple, according to vibrations that will be clearly felt during the operation of the gas station. You can adjust the fuel supply with your own hands by doing everything that is written in the instruction manual.

The motor can sulk due to the closed fuel valve. The reason is eliminated by its cleaning. If the benzokos started, and then sharply stalled, it means that fuel supply is difficult to the carburetor. Loosen the valves of the carburetor to ensure the free approach of fuel to it in the desired quantity.

With unnecessary air sacrifice, the engine can also stall. Add turns to the engine so that air bubbles come out faster from fuel system aggregate. Be sure to check the integrity of the fuel hose. In case of detection of mechanical damage (cracks, punctures, etc.), replace the item.

How to clean and store tool?

During the operation of the benzokosy, follow the status of the engine cooling system. Channels available in the starter housing, as well as the cylinder ribs, should always be clean. If you ignore this requirement and continue to operate the motocos, you can remove the engine due to overheating.

Competent care for gasoline oblique during operation allows you to use it several seasons in a row without serious repairs

Give the engine to cool before cleaning. Take a brush with a mild pile and clean the outer surface from the dirt. The purification of plastic parts is produced by solvents, including kerosene, or special detergents.

After the summer season, the benzokos must be prepared for long-term storage. For this, the fuel mixture merges from the tank. The engine is then running to produce fuel residues in the carburetor. The entire tool is well cleaned from pollution and goes on the "winter hibernation".

As you can see, the repair of faults of the household benzocos can be completely on their own. Service services should be handled in case serious breakdowns. At the same time, the cost of repair with the price of the new benzocos should be replaced. Perhaps it will be more expedient to buy a new tool.

This article will solve the placement of the benzokos when they sall on high revolutions on gas.

Build your home!

Benzokosa Glohnet

By purchasing benzokos, you must be prepared for the fact that, as in all other similar tools, breakdowns may also appear in it, which will require repair.

But it is not necessary to immediately run to the service center and pay large tools to the masters that repulse you in the presence of a grave malfunction in the device.

Benzokos stalls at high speeds on gas

Perhaps a more promatrated complaint associated with gasoline trimmers, it sounds like this: "Benzokos stalls."

Naturally, the prerequisite can be a sufficiently severe malfunction. But in most cases the situation is even easier than it seems on the 1st gaze.

To cope with such a problem, first, try without the help of others to deal with its reasons, because, finding out the reason, it is even easier to fight with a problem, and it is even self-destructed.

In fact, circumstances, it's when benzokos Blokhnet on high revolutions, there are many of these circumstances.

Why Chinese benzocos does not develop turnover?

Trimmer does not gain momentum, very frequent failure and of course not always has a normal solution. In this ...

Trimmer ne. gaining momentum, what to do?

1st launch of the newest benzokosy. The mesh with the silencer, began to work.

Another one is the presence of faults in the system.

In this case benzokos It will be stuck at idle. Problems with the power system can be brought to or incorrect adjustment of the carburetor.

Vibrations that have a place to be in the process of work of the benzokos can be brought to inclusion.

The wrong adjustment of the benzokos can be corrected by simply adjusting it in accordance with the requirements specified in the instruction manual.

In addition, sometimes gasoline trimmers can slander due to the fact that the valve located in the benzobacing lid simply clogged or the grain.

To find out this, try using braid, weakening the gas tank cover.

If in this mode, the device is properly operated, clean the valve.

Moreover, the benzokos can blah due to bad fuel flow in the carburetor

Why then the device starts, you ask?

The reason for this lies in the fact that first the fuel gradually runs to the carburetor and it is enough to work at high power.

However, it is also produced on large turns The engine begins to stamp.

As for the carburetor, there is also a problem here that its body is too pulled.

The reason for the fact that the benzocos stalls on high turns on gas, air dried may also be.

It is about the possible availability of space through which air can pass air during the engine heating.

Among other things, do not forget to check the tanning hose. The problem may be that it is weakly kept or worried at all.

These are the main reasons why May sick benzokos.

Read the same way

In recent years, the gasoline trimmer has acquired the status of one book from the main instruments in the Arsenal of Dachnikov. And such a situation is logical, because the motorized braid allows enough to rapidly lead the household plot in order. But upon that ...

Benzokos (Trimmer) Kuban BK-4500! Short review, launch, work. Item, electrocos and motocos (gas station) - varieties of lawn mowers, agricultural manual ... benzokos (trimmer) Kuban BK-4500! Runbenzokosa (trimmer) Kuban ...

Country business

Construction and cottage in your understandable language

What to do, if benzotrimmer not dial turnover?

If you once got a trimmer working with gasoline, you probably had to deal with the increasing trimmer inclusion, as well as with such a penalty, like benzotrimmer Does not gain momentum.

That is why this article is created.

So, what to do if the trimmer that works for you is no longer the 1st year, suddenly it stops to gain momentum, and the motor simply stalls? In this case, we will with you to see a series of problems associated with a motor stop.

The motor can be stuffed under different circumstances. The EFCO Stark 25 benzotrimmer does not develop turnover as if the gas is on a quarter what to do. From time to time the background of the wrong work of the trimmer operating from gasoline is to clog the air filter.

Specifically, the filter is one of the most important circumstances in which the work of a gasoline trimmer may end.

It often gets different garbage, there are dust particles, which also clog the filter, therefore it must be cleaned and washed every month, and maybe more often, everything is depending on what power is a gasoline trimmer, too, As often you use this device.

Trimmer is not gaining momentum, what to do?

Trimmer is not gaining momentum, very frequent failure and of course not always has a normal solution. In this.

Motokos Ne. gaining momentum, cause of malfunction and elimination of it

Description.