Effective operation of the car brake system depends on many factors. Non-only engine, transmission, suspension elements should be careful steering, but also the brake system. After all, the item rules road 10.1 reads - when dangerous for movement occurs, the driver must take all possible measures to reduce speed up to the stop vehicle. And what to do, if we wear, say, discs or pads?! It is not necessary to bring brake mechanisms that are so subject to predicted wear, to a critical state, when a cracked disk can easily block the wheel at speed and no longer, even the most modern intelligent aBS system 19th generation, will not be able to enter the dispute with the laws of physics and common sense.
Our current guest, to great joy, the situation does not through at all dramatism, rather, on the contrary. The owner bought the necessary consumables in advance and with the appearance of the first symptoms of the threshold wear, he gave a visit to the technical center "Auto Drive" on the South. Here should be reminded if someone did not know or doubted that brake discs With pads - 100% consumables. On this occasion, "our colleagues from the autotech center-twin" VAG X Motors "were hosted.
In turn, we invite you, dear friends, on the virtual course on the replacement and prevention of the front brake mechanisms car Hyundai IX35.
We throw off wheels, and proceed to visual inspection:
Yes, it's * Pistol *. No, they do not twist the nuts, but only on the contrary)
Wear front brake shoes Hyundai IX35
Wear, of course, takes place, although most readers say that there are still thousands and thousands of miles ahead. But look at the state of the brake discs - the fourth set of the pads they will definitely not bear:
Wear front brakes discs Hyundai. IX35
Moreover, the owner, from his words, feels in the steering wheel and on the brake pedal when slowing down from medium speeds. This could well be caused by overheating brake discs due to the decent method of developing and small residual thickness of the Ferodo layer on the brake shoe plates.
Let's proceed directly to the replacement procedure.
We unscrew the caliper:
Unscrewed stopping support Hyundai IX35
and remove old blocks:
Removing the Hyundai IX35 pads. The caliper remains hanging on the hook, the other end of which clings to the spring of the shock absorber.
Old pads with Hyundai IX35 brackets
Blow removal hyundai disk IX35
Photo from discharge "before and after":
Old and new components of the brake system HYUNDAI IX35
Preventive measures for many years of trouble-free front brake service look like this:
1) When replacing brake discs, it is necessary to remove traces of scale and any other dirt from the wheel hub. This is done in order to plant a new brake disk occurred without the slightest skew. After all, this, in turn, the key to uniform wear, and from here - the absence of vibrations / beats, irritating a violep and other troubles.
Hyundai IX35 Wheel Wheel Cleaning for Metal Brushing
2) high-temperature copper lubrication in the form of an aerosol applied to the contact surface of the hub and threaded connections To prevent the so-called. "Digging" and "Zaksania" details:
Surface treatment hubes Hyundai. IX35 high temperature copper lubricant
3) A powerful and efficient brake cleaner is used not only for rapid dissolution of oily dirt and degreasing brake mechanisms. Experienced auto showing successfully use it when conducting a wide variety of engine / transmission works as well as the chassis:
Cleaning the new brake disc Hyundai iX35 from the preservative lubrication
Disks are cleaned and sent to their rightful place:
Disk installed and fixed
4) Nehutral return forward movements with a brush for metal serving brakes with plates for installing brake pads:
Cleaning brackets front caliper Hyundai IX35
5) Abundantly, we assign a high-temperature lubricant guide caliper, which will not give the opportunity to twist moving parts of the brake system and ensure reliable functionality until next replace Brake pads:
Drawing high-temperature lubricant to Hyundai IX35 caliper guides
Slender nearby pads occupy their place in the brackets of the front caliper, and the node acquires a solid, almost its original appearance:
Installed new brake pads Hyundai iX35
Arming with a special set for piston information, moving to the final stage of the event:
Minding the piston in the Cylinder Spec. Tool
Wrench keys on "14" and "17" will help the mechanics reliably settle the caliper with the bracket:
When issuing a car, we may give the owner our traditional string recommendations on the inadmissibility of the active driving style of the first few hundred kilometers of run. During this period, it should be kept an increased distance to ahead of the walking transport, avoid emergency braking And to stop smoothly press the brake pedal until the new blocks and discs do not get to each other.
The total time spent on replacing the front brake discs with Hyundai IX35 pads amounted to 1 hour 30 minutes.
Our motto: "Do not wait for repair - to ensure prevention!"
Details:
Brake discs and pads (provided by the owner)
- Purifier brakes PARTNER (77701)
- Lubricant high temperature copper partner (30006)
At the checkout:
Replacing the front brake discs and pads: 1800 rubles.
- Prevention of guide front calipers: 400 rubles.
- Set supplies for fitter work: 400 rubles.
Characters:
Mechanic-car mechanic: Ruslan Sinynok
- Master receiver: Artyom Ponomarenko
We have in repair car Hyundai. IX35 (Hyundai Ai Xa 35), where you need to replace the rear brake pads, show how it can be done with your own hands without resorting to the help of specialists.
We tear the wheels, raise the cars and remove rear wheels. We unscrew the two guides, top and bottom:
Remove and remove in the direction of the brake cylindrik. Pull the old blocks. We check the work of the guides, in our case the lower goes gently and smoothly, the upper tight. I pull it out, clean and lubricate fresh high-temperature lubrication. We take a clamp or with its absence any suitable tool and press the "cylindrik":
Planting the pads clean with a brush with a metal bristle from the dirt. We have new pads with SANGSIN, a number in SP-1187 spare parts catalog. The inner block goes along with a "pisk", outdoor without. Install them in planting place. We put the cylinder and intimidate both bolts and upper and lower. Collect in reverse sequence. After the replacement, before starting the movement, two three times click on the brake pedal to press the pads to the disk. The work is done.
Video replacement of rear brake pads in Hyundai iX35:
Backup videos How to replace rear brake pads in Hyundai Ay Xa 35:
During the replacement of the pads, check the integrity of the entire brake system, see the condition of the caliper, hoses, anthers if necessary, make a replacement without fail, your life directly depends on this.
Brake pads do not have specific restrictions on the service life. It is recommended to check their condition after every 15,000 km of run.
If the car is used in difficult conditions (bad weather, the track), then it is necessary to make this procedure more often. A sign that the pads need to be replaced is the deviation from the reference indicator of the thickness of the lining. The norm must be no more than 11 mm. If the indicator differs significantly from this, then it means that it is necessary to put new ones urgently.
Blank replacementIX35 do it yourself It is quite simple, for this you will need only special tools: stops, lubrication, ratchet.
Replacing the rear brake pads Hyundai IX35 do it yourself
If you heard the corrosive wheels or other problems, then you should not delay the permission of the problem. The lining may arise in the near future. So:
Replacing the front brake pads Hyundai iX35 do it yourself
The car must be smoothly, not standing on elevations. It must be put on hand brake. Then:
Replacing the front brake padsIX35 do it yourselfenters the final stage. The following actions:
- The piston of the caliper is pressed back.
- You need to install it and secure bolts.
- If the brake is soft, it will be needed to pump it.
Replacement of brake pads onIX35 do it yourselfit is carried out quite quickly, especially if you already have experience. Choose the original material, which will help extend the service life.
We are pleased to offer you accessories for tuning Hyundai. IX35 with a 30% discount only for the readers of our articles. To learn more, click on the banner below:
Brake pads are strongly exposed to aggressive ambient, bad roads, excessive operation of the car and other factors. A sharp braking during travel through a puddle, often leads to a rapid failure of the brake pads due to the formation of cracks.
Replacing the front pads, work order
Technology for replacing the front brake pads on Handai IX35. The car rises on the lift or subdomains. The wheel is removed, then you will need 2 keys by 14 and 17. The first key is unscrewed the upper part of the caliper, the pads go. After that, behind the brake disc find the fastening of the caliper itself and unscrew it with the key to 17. Then cross scold Two bolts are unscrewed and removed. It is important to smear your fingers, as they often zaku. As a result, the internal and external parts of the brake pads are rapidly wear out. The pads change to new, the caliper is thoroughly cleaned from rust. The installation of the brake pads in the reverse sequence is assembled.
Replacing the rear brake pads
Replacing the rear brake pads on Handai AH35 is carried out similarly to the front. It is important to see the state of the brake discs. And in the case of developing on them to replace new or carry out a groove. And otherwise, even new pads are rapidly wear out. Also, after replacing the pads, it is necessary to pump the brake system, removing air from it. And the first few kilometers, after departure from the car service, it is necessary to slow down smoothly, without jerks. It is necessary that the brake pads come to the brake discs.
On all types of work on the replacement of the front and rear brake pads on the network of Hyndai car repair, a warranty is provided. In stock Original and non-original brake pads on the AH35 model.
Why do brake discs fail? This is, first of all, wear due to mileage, and also important, in what conditions a car is operated. With a frequent "sports ride", the discs are hot all the time, and, in case of entering them at this moment of water, deformation occurs, which is reflected by the beat when pressed on the brake and the steering vibration.
Replacing the front brake discs, work order
Technology replacement of front brake discs on Handai Ai Xa 35:
- tighten the handbrake
- wheels of car are removed
- caliper brake with brake pads
- the brake hose remains on the spot, without disconnecting
- fixed brake caliper wire to a shock absorber rack
- bolts fastening brake discs to wheel hubs
- removed brake disc with car studs
- cleaned from rust parts of the hub with which the wheels come into contact
- after that, in the same order is going brake system back
Replacing the rear brake discs
Replacing the rear brake discs on Handai IX 35 is similar to the replacement of the front. It can be noted that the production on them is not always a sentence to replace. If the brake discs of the car do not have cracks, and their thickness is sufficient, an economically more justified decision is not a replacement, but their flow. In this case, the surface of the brake discs is processed on a special machine and after removing the production and purification of rust, their further use is allowed.
All types of work on the replacement and flow of brake disc brake discs in the network of our Moscow car services are guaranteed. In stock There are disks both original and other manufacturers in Europe and Asia. Great experience Work allows us to offer our customers an excellent price / quality ratio.
