Programming StarLine B92. Starline operating instructions, model B92 Dialog

"Instructions for use Thank you for the choice of automotive security system StarLine B92 Dialog and wish you successful and safe trips! Revision number 1 ... "

user's manual

Thank you for the choice

automotive security system

Starline B92 Dialog.

and we wish you successful and safe trips!

Revision number 1.

Starline B92 Dialog.

READ PLEASE

CAREFULLY!

Installation of car alarm must be made

qualified specialists. Car alarm

is difficult technical deviceassumed

connecting to the car chains associated with the engine operation.

If the icon, warning about the discharge of the battery, appeared on the display of the keychain, take measures to replace the power item in advance. We recommend to store a new spare battery in the car, keeping its factory packaging.

Read carefully this instruction, the payment is special (attention!).

attention to sections marked with mandatory security measures When using the engine start function, it is necessary to remember that the car is a means of increased danger. Section 12.8. rules road says: "The driver can leave his place or leave the vehicle if they are accepted necessary measureseliminate spontaneous movement vehicle or use it in the absence of the driver. "

Before using the Starline B92 Dialog car alarm carefully read the measures of safe use of the remote or automatic engine start function set out below.

user's manual

1. Always park a car on an open, well-ventilated platform.

2. Always put the car on parking brakewhich should be in good condition and eliminate the possibility of moving the car.

3. Leaving the car, be sure to install the control lever automatic transmission In the "PARK" position, and the shift lever of the manual gearbox is neutral.

4. If a manual transmission is used in your car, then before turning on the function of the remote or automatic engine start, be sure to prepare the procedure for starting the engine - "software neutral".

5. Never transmit car alarm management key chainings, as well as other persons without their preliminary acquaintance with the instruction manual.

6. On cars with manual box The gear is not recommended to be remote or automatically start the engine if the car is outside the visibility zone, and the auto alarm user is not able to control the engine start process.

7. Before you include the remote or automatic engine start function:

Make sure in good condition of the car;

Make sure there is enough fuel, oil, coolant, etc.;

Set the operating parameters of the salon heater (air conditioner), glass heating and other accessories for the required levels;

Install the plugger regulator of the air circulation, which will allow you to warm more efficiently or cool the air in the car.

Starline B92 Dialog.

Contents of delivery

Specifications

Security and service signaling functions

Signal control using keychain keychain keychains

Duration Pressing Button Keychains

Basic teams Brecks

Liquid crystal display keychain

Indication of active modes and functions

Alarm and car status indication

Menu functions of the main key

Programming modes of operation by the cursor way

List of modes programmable by the cursor

Security I. anti-theft functions Auto alarms Enabling protection with sound signals confirmation

Inclusion of protection without sound signals Confirmation

Inclusion of silent security

Automatic security switching on

Enable protection with a running engine

Remote engine stop without shutting down the security mode ...... 32 Inclusion of protection without a keychain

Automatic Return to Protection Mode

Bypassing the salon light (sensor activation delay)

Self-diagnostics when incorporate protection

Turning off protection with sound signals confirmation

Shutting down protection without sound confirmation signals

Turning off protection without using a keychain

Turning off protection with a running engine

Self-diagnosis when disavoving security

Alarms

Signal protection from power outage

Additional sensors

operating Instructions Additional Wireless Lock Relay

Connecting information search GSM modules

Anti-primilation mode

Enable anti-diagnosing mode by keychain

Hidden inclusion of anti-labeling mode

Turning off the anti-labeling mode

Mode "Panic"

Immobilizer mode

Turn off the engine lock in immobilizer mode

Service Function Functions Car Control, Akb and Salon Temperature Voltage ... 53 Finding a Car Parking and Engine Temperature Control .................. 54 Temporary shutdown of the shock sensor

Temporary disconnection of an additional sensor

Automatic control of door locks

Remote Control Locks Doors

Additional channel control №1

Control of additional channel number 2

Control of additional channel number 3

Control of an additional channel number 4

Turbotimer mode

Turning on turbo-timer

Call from car

Light indication open doors

Controlling the charge element keychain with LCD

Control service life switches

Mode service

Alarm viewer feature

Automatic communication channel control

Monitoring the number of key chains recorded in the system

Lock buttons keychain

Personal Code Emergency Disable Protection Mode

Personal Code Input Algorithm

Recording codes Brecks

Starline B92 Dialog.

Remote Engine Start Features remote launch Engine

Preparation for remote launch on cars with manual gearbox ........... 75 Enable software neutral

Remote engine start by keychain

Remote engine stop

Remote engine extension

Automatic engine start

Automatic Starting Engine Budil

Periodic engine launch

Automatic engine start time

Programming Functions Programming Security and service functions (Table No. 1) ............... 84 Programming Engine Run Settings (Table No. 2) ............... 86 Elements of Breasters and Their replacement

operating Instructions Introduction Starline B92 Dialog - Modern Car Security System.

The protective properties of the system are implemented by innovative technologies.

To transmit control commands to Starline B92 Dialog, a unique authorization algorithm "Fast dialog" with a crypto-resistant code and an individual encryption key, eliminating intelligent electronic hacking, is applied.

- & nbsp- & nbsp-

StarLine B92 Dialog Supplies 1, 2 - Installation and Operating Instructions;

3, 4 - memo and warranty card;

5 - Keychain remote control with feedback and liquid crystal (LCD) display;

6 - central processor block;

7 - a transceiver module with antenna;

8 - Keychain remote control without an LCD display;

9 - two-level impact sensor;

10 - power supply for a keychain with LCD;

11 - hood button;

12 - Temperature sensor with 2-pin cable;

13 - service button;

14 - shock sensor cable;

15 - LED Indicator 16 - Engine temperature sensor connection cable 17 - transceiver cable;

18 - power cable and engine start circuits;

19 - main cable with a 18-pin connector;

20 - wires connecting limit switches;

21 - cable of the central lock with a 6-pin connector;

starLine B92 Dialog Operating Instructions Specifications

IntroductionArdrudy signal management..OT433,075D434,775MHz

Quantity of quantities

Maximum ParametersInformation Breakers

In the command transmission mode, alarm unit

In the mode of receiving signals from the alarm unit .................. 2000 m *

Maxue Parademide Pharmacy ............ 15m *

Tipdatcher

Working temperature

Voltage supply permafront

Current, consumption. Signalization of self-refinery .... not more than 2005

The maximum allowable current at the outputs:

ConnectingSyrene

Connections LifterSignals

Controllelectriborovodamovogamdverey

Inclining

Inclusive accessories

Inclusion Starter

Built-in bugger

OfficeClochetor.

Additional Facilities

Power supply equipment: .......... 1.5V (1 Elementipania "AAA")

Phase-performing machine: ... 3B (1Element "CR2450") * The range of the keychains can decrease depending on the place of installation of the transceiver, the location of the car and the user, radio frequency interference, weather conditions, voltage car battery and voltage element of the battery.

Starline B92 Dialog is allowed to use on the territory of the Russian Federation and meets all the requirements of regulatory documents of the Russian Federation.

The service life of StarLine B92 Dialog is 5 years, provided that the product is installed and operated in accordance with installation and operation instructions.

operating Instructions Security and Service Signaling Functions Protected Car Zones and Methods for their control

Engine - Lock Relay, Digital Radiorele StarLine RD02 (Option)

Doors, hood, trunk, parking brake - limit switches

Ignition - Ignition Chain Control Input

Body - two-level impact sensor

Interior Salon Space - Additional Sensor (Option) Signaling Protection

Dialogue Management Code "Fast Dialog" with individual encryption keys eliminates intelligent electronic hacking

Patented 512 channel narrowband transceiver provides reliable work in urban interference

Memoring the original state when the power is turned off and returning to the same state when power is reduced

Interrupting alarms without shutdown mode

Restricting the number of alarm cycles from sensors

Automatic communication channel control Protective and anti-theft alarm functions

Protection mode with sound and light alarms

Feed alarm alert signals by keychain with LCD display (main keychain)

Sobbery Overclock / Turn-off

Silent security mode

Protection Mode with Operating Engine

Pustine / Turn-off-poweredBerebrecks

Automatic return to the protection mode during accidental shutdown

Starline B92 Dialog.

Automatic switching on the security mode

Immobilizer mode

Anti-primilation mode

Mode "Panic"

Programmable Personal Emergency Code

Engine lock and save it when dismantling alarm

Programmable 2-step shutdown engine locks Self-diagnosis and indication of operation modes

Indication of faulty zone when the protection mode is turned on

Indication of the causes of signaling of 9 protection zones

Indication of alarm status LED and on the display keychain

Displaying alarm factory indication by sound signals

Automatic control of security sensors with disconnecting defective and shutdown message

LED indication of the service life switches

Keychain with an intuitive display

Comfortable backlight display 3 different sound modes and vibration work keychain

View the alarm history Service alarm functions

Walking around the door zone for the time of delaying salon light

Vertifying Signal Significance / Turning Offs

Remote shutdown of the shock sensor and an additional sensor in terms of protection mode

Remote control of the central lock

Management of the central lock from the ignition castle

Two-step unlocking door locks

Two-pulse locking of door locks 4 channels for additional equipment

Car battery voltage control instruction manual

Separate temperature indication in the cabin and under the hood of the car

Advanced implementation of the "Comfort" function

Function "Car Search"

Light outdoor light alarm

Turbotimer mode

Remote programming of functions and keychains

Service mode

Car Lighting Control

Call mode from car (keychain search)

Protection against accidental pressing buttons

Programming new and erasing of lost key chains

Current time indication, alarm clock, countdown timer

Indication of the discharge of the batter element of the main key

Collaboration with GSM Modules Starline Space, Starline Messenger M20 and Starline Messenger GPS M30 Engine Run Functions

RemotePask / Extension / stopper

Automatic start of the engine at a temperature, over alarcill, periodic launch every 2, 3, 4 or 24 hours

Remote engine start on vehicles with start / stop button

Plotisitel: Gasoline / Diesel

PlotpaTransmission: automatic / manual

Motor control over the signal of the tank, generator or voltage of the on-board network

Automatic protection from the twist of the starter when starting the engine

Indication of the remaining running time of the running engine on the display of the STARLINE B92 Dialog keychain control using keychain keychain keychains The system is equipped with two control key chains.

Main key chain: Additional keychain:

4-button keychain with a reverse 3-button keychain by bond and liquid crystal without a display (LCD) The main and additional keychains are equivalent to cryptostility.

To transfer control commands in both keychains, a special encryption algorithm "Fast dialog" is used, eliminating intelligent electronic hacking.

Information about the status of the security system is transmitted to the main key chain

Triggered sensors and anxiety

Execution of commands transmitted from other key chains

Change operation modes and signaling functions.

At the same time, the display shows the current alarm status, sound, vibration signals and display lights.

In addition, on the LCD display, the keychain is displayed about the current time, the alarm clock, timer, battery voltage, engine temperature and car interior.

instructions for use in order to maximize the use of the capabilities provided by the security system, we recommend using the main control key chain.

The duration of clicking the key chains buttons in this section and then the following definitions of the duration and sequence of pressing the key chain buttons are used:

Short pressing is one press of a button (or two buttons) duration less than 0.5 seconds.

Long press - pressing and holding the button or two buttons before the melodic sound signal appears.

Double pressing - two pressing of one button for 1 second.

Sequential pressing - two pressing of one or different buttons. The first press should be long (before the appearance of the sound signal), the second press is short-term (after the first button is released).

- & nbsp- & nbsp-

StarLine B92 Dialog Liquid Crystal Display Charming and Indication of Active Mode and Functions Automatic Starting Mode

- & nbsp- & nbsp-

Alarm and Car Status Indication Enabled Alarm Sound Alarm Mode Included Mode Silent Protection Door Locks Closed Door Locks Open ignition Open Open Doors, Hood, Trunk Does Not Tightened Parking Brake (Pressed Foot Brake) Engine Works Enabled Anti-Frame Mode Required Power Single Engine Connected Love SummodulesStarLineGSM / GPS Enabled Alarm Clock Included Timer Keychain is in the reception zone of signals Alerts bypassing the 1st level sensor Sensor bypassing the 1st level of the additional sensor bypassing both levels of the shock sensor bypassing both levels of the additional sensor worked the 1st level of the impact sensor The level of the additional sensor worked the 2nd level of the shock sensor worked the 2nd level of the additional sensor worked 1-level additional sensor No. 1 1-level additional sensor No. 2

Starline B92 Dialog.

Menu functions of the main key

Menu of the functions of the main keyboard allows you to:

Set the current time

Set the time alarm

Enable or disable alarm clock

Set the time countdown timer

Turn on or off timer

Select alarm volume or silent mode

Select the audio type

- & nbsp- & nbsp-

If there are no press on the buttons for 8 seconds, an automatic way out of the programming mode of the keychain will occur.

StarLine B92 Dialog Programming Operating Modes The cursor way Separate signaling modes, as well as some special functions are programmed (enabled or turned off) by the cursor. The included state of any of the modes is indicated by constant illumination of the corresponding icon at the bottom of the display keychain.

Programming is possible both when the security mode is turned off and when turned on.

For programming, execute the following actions:

- & nbsp- & nbsp-

After the 2 signal is performed at the bottom of the screen will be highlighted by flashing the first left icon:

Short presses on the 2 2 buttons (left) or 3, 4 (Right) Move the flashing cursor to the desired icon:

- & nbsp- & nbsp-

If there are no press on the buttons within 5 seconds, it will automatically exit the programming mode to the cursor.

Starline B92 Dialog List of modes programmable by the cursor mode Automatic start-up mode.

Allows you to automatically start the engine during the alarm programmed.

Automatic periodic start mode.

Allows you to perform a periodic start of the engine every 2, 3, 4 or 24 hours (depending on the choice).

Automatic launch mode temperature.

If the engine temperature drops below the installed threshold, the engine will automatically start to warm up at a specified time.

Service mode. Designed to temporarily disable security and anti-theft signaling functions if you need to transfer a car for service or repair.

Turbotimer mode. Designed for cars with turbocharged and allows you to keep the engine operation after turning off the ignition for some time necessary to reduce the speed of rotation of the turbine.

Automatic security mode. The protection turns on automatically after turning off the ignition and after 10 seconds after closing all doors.

Immobilizer mode. In this mode, the engine is automatically blocked after 30 seconds after the ignition is turned off.

For more information about the operation of the listed modes, see the appropriate sections of the instruction.

- & nbsp- & nbsp-

Security and anti-theft functions of auto alarm Enable protection with sound signals confirmation Before turning on the security mode, make sure that

Ignition off

Parking brake is turned on

Doors, hood and trunk closed

- & nbsp- & nbsp-

If the doors, the hood, the trunk will be bad closed, and the parking brake is not tightened (or foot brake pressed), or is faulty (permanently closed) one of the end switches of doors, hood, trunk, then the alarm will warn about this 4 siren signals and 4 light signals (See "Self-Diagnosis When the Protection Mode is on, p. 34).

StarLine B92 Dialog Include protection without confirmation sound signals Before turning on the security, make sure that

Ignition off

Parking brake is turned on

Doors, hood and trunk closed Press the key chain 1 first 1 long (until the audio signal appears), then briefly

- & nbsp- & nbsp-

If the doors, the hood, the trunk will be bad closed, and the parking brake is not tightened (or foot braking), or is defective (constantly closed) one of the end door switches, the hood, trunk, then the alarm will warn about it with 4 light signals (see " Self-diagnostics when the protection mode is turned on, page 34).

- & nbsp- & nbsp-

The inclusion of silent protection in the mode of silent protection when the vehicle siren signals are missing from any of the security sensors are missing.

The alarm status is accompanied only by light signals.

- & nbsp- & nbsp-

1 Luminous signal will sound 1 signal

Doors locks will appear displayed indication

The LED indicator of the silent security will flash if the doors, the hood, the trunk will be poorly closed, and the parking brake is not tightened (or foot brake is pressed), or is faulty (constantly closed) one of the end switches of doors, hood, trunk, then alarm will warn about it 4 light signals (see "Self-diagnostics when the security mode is turned on, page 34).

Starline B92 Dialog Automatic Enabling Protection To use this mode with a cursor (see page 24) "Turn on" icon on the keychain display.

When you closed doors, turn off the ignition, exit the car and close all the doors.

car 1 Siren Signal 1 Luminous Signal

- & nbsp- & nbsp-

Inclusion of security with a running engine before turning on the security Make sure

The car is on neutral transmission (or in PARK mode with automatic transmission)

The hood is closed, the engine is running

- & nbsp- & nbsp-

1 Siren Signal 1 Signal 1 Luminous Signal Operating Engine Indication

A sensor and shock enabled will be turned off. Sensor and regime Controlling protection zone

Doors locks closed

Starline B92 Dialog Protection Mode If the parking brake is not enabled or the hood is open, then when executing item 1, indicating the engine of the engine and the remaining engine operation time (R10, or R20, R30, R99) on the display the keychain will not appear on the display.

After the installed time of the engine is expired, the function 2 tab. No. 2) the engine will be stopped without shutting down the security mode.

Remote engine stop without shutdown Security mode Press the 1 button for a long time (before the audio signal appears), then button 4 short car keychain

- & nbsp- & nbsp-

Inclusion of protection without a keychain before turning on the security Make sure

Ignition off

Parking brake is on 1 Open one of the doors and turn on the ignition

- & nbsp- & nbsp-

The countdown of 20 - second interval will begin, after which the security mode will turn on 3 out of the car and close all the doors.

- & nbsp- & nbsp-

after 20 seconds, after turning off the ignition, the protection mode will automatically turn on:

1 siren signal will sound, light signals will flash 1 time

Door locks close if at the time of the protection turns on the door, that the doors, the hood or trunk are badly closed, the parking brake is turned off (the foot brake is pressed), or is faulty (constantly closed) one of the end switches of doors, the hood, trunk, then when you turn on the protection, the alarm will turn off The protection of this zone. Four signal sirens and 4 light signals follow.

StarLine B92 Dialog Automatic Return to Protection Mode If you are programmed automatic return to the security mode (function 5 tab. No. 1) and within 30 seconds, after turning off the protection of the door, the car did not open, the alarm will automatically turn on the security mode.

Attention! Locking the door locks will occur if they are connected to the alarm and programmed the version of the bus route to the protection mode with locking door locks (function 5 tab. No. 1).

Re-enabling the protection mode is confirmed by 1 siren signal and 1 vehicle light signal. 1 signal keychain sounds.

The engine will be blocked. The LED will flash, indicating that the car is guarded.

If one of the end switches of the hood or trunk is faulty, then after switching on the security, 4 sirens and 4 light vehicle lights follow.

1 signal keychain sounds.

Bypassing the cabin light (sensor activation delay) The delay in the activation of the sensors may be necessary to bypass the door zone at the time of the smooth extinction of the cab cabbage or to calm the shock sensors or volume. Otherwise, when the security mode is enabled, false alarms may follow.

Depending on programming, 5, 30 or 60 is a second delay (Function 3 of Tab. No. 1).

Self-diagnosis when the protection is turned on when the protection is turned on, the alarm automatically checks all zones that must be taken to guard

- & nbsp- & nbsp-

Doors, hood or trunk badly closed

Faulty (constantly closed) one of the end switches of doors, hood, trunk

Not included parking brake

- & nbsp- & nbsp-

In the case of spontaneous troubleshooting, when the mode is enabled, the alarm will automatically automatically take this zone for protection.

StarLine B92 Dialog Turning off protection with confirmation audio signals Press the 2 key chain

- & nbsp- & nbsp-

Turning off protection without sound confirmation signals Press the 2 keychain first for a long time (until the audio signal appears), then briefly

- & nbsp- & nbsp-

If the "Double-step shutdown of the engine locks" is turned off (function 11 of the tab. No. 1), the engine will be unlocked simultaneously with the shutdown of protection.

If this mode is turned on, then open the door to unlock the engine, turn on the ignition and enter the personal code (see page 72). If the code is entered correctly

Two siren signals and 2 light signals follow.

Engine lock will be turned off.

If, when the security is turned off, 3 sirens and 3 lights and 3 lights are followed, this means that the sensors were triggered in the protection mode (see "Self-diagnosis when the security is turned off", p. 40).

StarLine B92 Dialog Turning off Protection without using a keychain 1 Open the car door key

- & nbsp- & nbsp-

Alarms will begin (if the protection mode was turned on by a keychain)

4 flashes of light signals will follow (if the protection mode was turned on without a keychain) for 20 seconds, turn on the ignition 2 and enter the personal code (see page 72)

- & nbsp- & nbsp-

After entering the last digit of the code:

2 Sirens Signals

Light signals flashed 2 times

Protection mode will turn off if when the security is turned off 3 siren signals and 3 light signals follow, this means that the sensors were triggered in the protection mode (see "Self-diagnosis when the security is turned off").

- & nbsp- & nbsp-

StarLine B92 Dialog Self-Diagnosis When the security is turned off when the security mode is turned off, the alarm informs about the sensors during the protection of the triggering of the sensors. Turn off the security mode by pressing the 2 keychain button.

If the alarms interrupted with the keychain:

- & nbsp- & nbsp-

Alarms If in the security mode there will be a trigger of any of the security sensors, it will cause it automatic inclusion Alarms: Siren signals and light signals.

The keychain will serve sound alarms, and the display shows the reason for the alarm operation.

During the sound of the siren on the display, the icon corresponding to the cause of the trigger will flash.

Alarms are fed by cycles.

The duration of one alarm cycle and the maximum possible number of cycles for various causes of signaling is shown in the table below.

- & nbsp- & nbsp-

1) While the lights of the car flashes, the headlights of the car will flash on the display.

2) If, after the end of the alarm cycle, the reason for the alarm response will not be eliminated (for example, the doors remained open), then the protection of the corresponding zone is turned off until the cause of the cause of the trigger (for example, before closing the doors). At the same time, on the display keychain indication of the cause of the triggering is saved.

3) If the alarms interrupted with the keychain, then the number of alarm cycles at a periodically triggering sensor begins again.

- & nbsp- & nbsp-

Display alarm alarms on the display keychain

The 1st level of the shock sensor has worked the 2nd level of impact sensor

Worked the 1st level add. The sensor worked the 2nd level add. Sensor

Worked single-level add. Sensor No. 1 worked single-level add. Sensor №2.

- & nbsp- & nbsp-

Signaling the power to turn off the short-term shutdown of the alarm power (for example, the reset of the battery terminal) does not lead to the removal.

The alarm remembers its state and when the power is restored, it turns out again in the same mode at which there is a shutdown (see the status table below), the melodic signal of the keychain will follow.

If a siren with autonomous power is connected to the system, then when the siren battery terminal turns on the alarms.

- & nbsp- & nbsp-

Additional sensors as an additional sensor to car alarm can be connected to both 2-level sensors (for example, microwave MWS203) and 1-level (for example, a combined pressure sensor and tilt PTS 01, PS 01 pressure sensor, TS 02 tilt sensor) .

Connecting the sensors is carried out to the 4-pin connector with cables included in the sensor kits.

After connecting the sensors, you must program the function 4 tab. №1 Depending on the type of sensor used.

Starline B92 Dialog.

Additional wireless lock relays Using a digital engine blocking radios (StarLine RD02) allows you to significantly increase the anti-theft functions of the car alarm due to the hidden setting of the Radio in the standard car wiring and the lack of any wired connection between the central alarm and radio engine.

Connecting information search GSM modules Information and Search modules Starline Space, Starline Messenger M20, Starline Messenger GPS M30 is specially designed to control Starline alarms and locating a car. Their application makes it possible to control the alarm, receive messages about the invasion of the car, determine the location of the car almost without distance limit - wherever there is a GSM network.

Transmission of information and control commands occurs through the GSM communication channel.

An alarm information (operation of security sensors) and the location of the car can enter the owner's phone in the form of SMS messages or calls with a speech message.

The view of the alert is programmed by the owner.

Modules are connected to the STARLINE 3-wire cable signaling included in the module package.

- & nbsp- & nbsp-

Anti-Frame mode To use anti-diagnosis mode 8 tab. # 1 must be programmed to option 1 or 2.

Turning on the mode of anti-label keychain Attention !!!

After turning on the anti-diagnosis mode, the keychain is not possible to turn it off.

To turn off, you must enter a personal code.

When the ignition is enabled or when the engine is running, simultaneously press and hold the buttons 1 and 3 keychain

- & nbsp- & nbsp-

The constant sound will be included. Signal and light alarm lights will sound.

Doors locks will be turned on

Depending on the state of the vibrating signal of the programmable function, 8 tab .№1 The engine will appear on the screen will be blocked the mode icon either immediately or after turning off the anti-label manual brakes (Pages on the brake pedal). During the first 30 seconds, the blocking occurs impulsively, then continuously

Starline B92 Dialog.

The hidden turning on the anti-label mode The hidden turning on the anti-label mode can be applied in a situation where to counteract other methods is difficult or impossible.

The mode is activated when opening the doors in case of leaving the car owner, after which the system acts automatically according to a specific algorithm consisting of several stages.

Close the door of the car. With the 1st stage: the engine or when the ignition is turned on, press the service button for 2 seconds after pressing the service button is activated by the standby mode in which the alarm expects the opening of the door. No indication of the inclusion of standby mode is missing. Standby mode can continue an unlimited time. While all the doors continue to remain closed, the alarm does not have any influence on the function of the car. After opening one of the doors, the second stage of the anti-label algorithm 2 is automatically activated: Open one of the doors any alarms at this stage are missing, the lock is turned off. From the moment the door opening began the countdown of the 60-second time interval, after which the alarms will be enabled. Make sure that the second stage of the anti-label mode is enabled by clicking the 3 keychain button. The display will flash the icon of the anti-label mode.

- & nbsp- & nbsp-

The permanent signals of the sirens will turn on

Intermittent engine lock will be turned on immediately or after turning off the manual brake (pressing the brake pedal)

Light alarms continue

- & nbsp- & nbsp-

Continuous sound and light alarms continue

Enable constant engine lock ATTENTION !!! If you need to land passengers, and the anti-label mode is turned on before opening the doors - turn off the anti-label mode (press 2 keychain). Otherwise, after 1 minute, alarms will begin after opening any door. Even if you forgot about it, it is possible to turn off the anti-label mode by the keychain on 1, 2 and 3 stages (the intermittent engine lock is not turned on).

StarLine B92 Dialog Turning off the Mode of Anti-Frame Attention !!! If the anti-label mode has been turned on by a keychain - it is possible to turn it off only by entering a personal code:

- & nbsp- & nbsp-

Press the 2 keychain button when the ignition is turned on after turning on the intermittent engine lock, turn off the anti-label mode can only enter the personal code (see page 72).

- & nbsp- & nbsp-

Mode "Panic"

When you activate the "Panic" mode for 15 seconds, light and sound alarms are included. If the security was turned off - the security mode turns on.

When the ignition is turned off at the same time, press buttons 1 and 3 keychain

- & nbsp- & nbsp-

For 15 seconds, it will be activated 1 short signal. Sound and light lights appear. Displaying alarm

Doors locks will be closed (if they were open)

Protection mode will turn on (if the protection was turned off) after the end and sound alarms, the protection mode will remain enabled.

For interrupting alarms in "Panic" mode, press 2 keychain. Alarms will stop.

Alarm will remain in the mode of protection.

StarLine B92 Dialog Immobilizer Mode To use this mode "Turn on" to the cursor (see page 24) icon on the keychain.

- & nbsp- & nbsp-

The keychain will constantly display the icon:

With programmed immobilizer mode, the engine will be blocked automatically, after 30 seconds after each ignition shutdown.

Turn off the engine lock in immobilizer mode Press the service button on 2 s, then turn on the ignition

- & nbsp- & nbsp-

Service Function Functions Car Control, Akb Voltage, Salon Temperature This command You can use in any mode to check the current status of alarm, check the battery voltage and temperature in the car. Press the bus 3 keychain

- & nbsp- & nbsp-

The temperature sensor is located in the central alarm unit. Therefore, the temperature displayed on the keychain may differ from the real temperature in the cabin, as it depends on the installation site of the alarm unit. Temperature measurement range: from - 40 0CO +70 0C.FextherautravoidsAmkato-modpazone, the indication on the display keychain will be shown as shown on page 54.

StarLine B92 Dialog searching for a car in the parking lot and control of the engine temperature This command can be used in any mode to search for a car in the parking lot and monitor the temperature of the engine Press the button two times short

- & nbsp- & nbsp-

The thermometer icon to the right of the car is a sign of an engine temperature indication.

If the temperature is below - 400X + 700C display will look like this:

- & nbsp- & nbsp-

The temperature displayed on the display keychain may differ from the actual engine temperature, as it depends on the location of the temperature sensor.

- & nbsp- & nbsp-

In Protection Mode, press twice 3 briefly button 1 keychain.

The shock sensor will be turned on again during one security cycle, you can turn off the shock sensor over the levels and its reverse inclusion Unlimited number times.

During one security cycle, you can shut down an additional sensor over the levels and its opposite inclusion unlimited number.

- & nbsp- & nbsp-

If two single-level sensors are connected as an additional sensor (2 tab. No. 1), then when the first sensor is turned off at first, the first sensor turns off, then both sensors are turned off, then both will turn on.

Automatic control of door locks as additional features Comfort and safety is possible selection of four options for automatic control of door locks when the ignition is turned on (off).

Control options are determined by the programmable function 2 tab. №1.

- & nbsp- & nbsp-

Control of an additional channel No. 1 Options for the operation of an additional channel are determined by the programmable function of 13 tab. №1. 4 options are possible.

Channel activation is made by the same actions, regardless of the selected option:

- & nbsp- & nbsp-

If, when you activate the channel, the trunk will not open, then the indications of the open trunk and the disconnected sensors on the display the keychain will not follow. After 20 seconds, the trunk zone will be again taken on guard.

- & nbsp- & nbsp-

View additional equipmentconnected to channel number 1, refined when installing alarm

- & nbsp- & nbsp-

Control of an additional channel number 2 Options for operation of an additional channel are determined by the programmable function of 14 tab. №1.

4 options are possible:

Option 1: Two-step unlocking door locks Turn off the security mode by pressing the 2 keychain button

- & nbsp- & nbsp-

To unlock the castles of the rest of the doors, press the 2 key chain to implement the two-step unlocking of the door locks. The driver's door activator and the activists of the other doors must be connected in accordance with the schema shown in the installation instructions.

For options 2 or 3, the channel can be programmed to any fixed duration of operation from 1 to 120 seconds. If Option 2 is selected, a shock sensor and an additional sensor are disconnected during the operation of the additional channel.

If the option 3 is selected - the sensors are not disconnected.

- & nbsp- & nbsp-

In the "Latch" mode, with each channel activation, the output status is changed to the opposite.

To activate an additional channel number 2 in case of options 2, 3 or 4 - press the 3 keychain button for a long time (before the audio signal appears), and then button 1

- & nbsp- & nbsp-

Control of an additional channel No. 3 Options for the operation of an additional channel number 3 are determined by the programmable function of 15 tab. №1.

Channel is used to connect autorun.

More detailed information The operation of the channel number 3 is provided in the installation instructions.

Control of an additional channel No. 4 Options for the operation of an additional channel number 4 are determined by the programmable function 12 tab. №1.

Channel activation is automatically performed.

The channel can be programmed to any fixed duration of operation from 1 to 120 s.

The channel output is used, for example, to include "polite illumination", "light path" or automatic raising glass when the protection is turned on.

More information about the operation of an additional channel number 4 is provided in the installation instructions.

StarLine B92 Dialog Turbotimer Mode to use Turbo-Mode

Function 12 tab. # 2 must be programmed to one of the ignition support options.

On the display, the keychain must be "enabled" icon (see "Programming the operating modes of the cursor way", p. 24).

- & nbsp- & nbsp-

2 Remove the key from the ignition lock. If you need to put a car on guard, go out of the machine, close all the doors and click on the key chain 1

- & nbsp- & nbsp-

At the end of the specified time of the turbotimer (Function 1 tab. No. 2)

The engine will be turned off

If the security mode is enabled, then the ignition zones, the shock sensor and the additional sensor will be taken to protect the call signal, press any button keychain light indication of the open door if the programmable function is 7 tab. No. 1 is enabled, when opening any of the doors, the alarm lights will warn you that the doors are open.

The duration of the warning light signals can be programmed by 10, 20 or 30s.

Controlling the charge element keychain with LCD control charging element keychain is performed every time you press the keychain buttons

- & nbsp- & nbsp-

Control of the health of the limit switches in the alarm is possible to control the health of the end switches of the doors, the hood and trunk when the protection mode is turned off. Opening the doors, the hood and trunk when the ignition is turned on, must be accompanied by periodic flashes of the LED state indicator. If the flashes of the indicator are not observed, it means that the corresponding terminal switch is faulty (or not connected to the alarm).

The serviceability of the limit switches, as well as the correct connection of the ignition circuit, can be checked using the indication on the keychain:

Open the door, hood, trunk, turn off the manual brake and turn on the ignition. Press the key chain 3 keychain

On the display, the state of the above-mentioned zone of warning zones will be displayed:

Consistently check all zones:

Close it, press3, press3,

Closecapot, pressing3,

Close Bag, press3,

Enabledroduks, press3, click3,

Turning the incorporation, pressing3, each time you press the button 3, the icons of the corresponding protection zones must disappear on the keychain.

Starline B92 Dialog.

Service Mode To temporarily disable anti-theft and security alarm functions, for example, when transferring a car to the station maintenanceIt is recommended to enable service mode.

For this skew (see page 24) "Turn on" on the display keychain icon

- & nbsp- & nbsp-

Service Mode cannot be activated when the security mode is enabled.

The alarm view feature The alarm viewer is designed to diagnose false positives. In the event of alarm, information about the sensor and response time remains in the alarm memory. In total, the memory can be stored up to 8 recent alarms. For example, if 8 shock sensor triggers occurred, and the alarms were not discharged by a key chain, 8 entries will be stored in the alarm memory to respond to the shock sensor.

Viewing is as follows:

- & nbsp- & nbsp-

Turn on the blocking of the keychain 1 (see page 71) by simultaneously pressing the buttons 2 and 4. Long press the 4 keyword button 2 until the display of the last recorded alarm (alarm No. 1) is shortly pressing the button 4 View the 3 List of Alarms. When you press the button 3, the alarm time will appear

- & nbsp- & nbsp-

STARLINE B92 Dialog Automatic control of the communication channel in automatic control mode at a given time intervals (3, 5 or 7 minutes), a communication channel is checked between the central alarm unit and the keychain.

- & nbsp- & nbsp-

Control channel control is carried out only in protection mode. Options for automatic control of the communication channel are set to a programmable function of 16 tab. №1.

Control the number of key chains recorded in the system when the ignition is turned on and the door closed, press the 3 keychain button. The number of outbreaks of the LED indicator status will correspond to the number of key chains recorded in the alarm memory.

- & nbsp- & nbsp-

A short beep sounds

Short vibrating signal

Icon will disappear

Blocking buttons will turn off the personal code of emergency disabling the protection mode Personal code of emergency disabling the protection mode or anti-label mode may consist of 1, 2 or 3-digit, each of which can be made from 1 to 6 inclusive. The procedure for programming a personal code is described in the installation instructions.

When delivery (or after resetting to the "factory settings"), the personal code is "3" (see the function 9 tab. No. 1).

StarLine B92 Dialog Algorithm Input Personal Extra Shutdown Code Open the door with the key and leave it open

Alarms will begin (if the security was included by the keychain)

4 light signals will flash (if the security was turned on without a keychain)

No signals will follow (if the security mode is turned off)

Enter 1st digit:

1 Turn on the ignition. Press the service button the number of times equal to the first digit of the code. Turn off the ignition.

If the code is 1- digit and it is entered correctly, the alarm will turn off the security mode, 2 light signals will follow

In the case of 2 or 3 digit code - enter the following digit:

Enter 2nd Figures:

2 Turn on the ignition. Press the service button the number of times equal to the second digit code. Turn off the ignition.

If the code is 2 digit and it is entered correctly, the alarm will turn off the security mode, 2 light signals will follow

In the case of 3 digit code - enter the following digit:

Enter 3rd Figures:

2 Turn on the ignition. Press the service button number times equal to the third digit code. Turn off the ignition.

If the code is 3 digit and it is entered correctly, the alarm will turn off the security mode, 2 light signals will follow

- & nbsp- & nbsp-

Recording codes Keychains Recording codes Keychains are performed when the protection mode is turned off in the following order:

1 Press the service button 7 times and turn on the ignition

- & nbsp- & nbsp-

Repeat item 2 for all other recorded keychains. The interval between the record should not exceed 5 seconds. The successful record of the next keychain is confirmed by the corresponding number of siren signals.

3 Turn off the ignition.

- & nbsp- & nbsp-

Follow 3 light signals ATTENTION! In total, you can write up to 4 key chains in the alarm memory. When recording new key chains, it is necessary to overwrite both old, otherwise they will be removed from the alarm memory.

To record a 3-button keychain without a display, the combination of buttons 1 and 2 is also used.

StarLine B92 Dialog Remote Engine Start Before running the engine by keychain or activate automatic launches Requireorly read the features of the remote engine launch:

Features of the remote engine launch remote engine start can not be implemented in the following cases:

Inclusive ignition

Opened hood

Off the parking brake or the foot brake is pressed

No preparation for the launch of the engine on vehicles with RCPP (software neutral)

1. For one startup cycle, the system can take 4 attempts to start the engine. If, after the 4th attempt, the engine does not start, then on the display with a feedback keychain (provided that it is in the reception area) will be displayed "OST" and the keychain will supply 4 beeps, which denotes the end of the engine start attempts.

Four car lights will follow.

2. If remotely running engine Strong until the end of the programmed warm-up time, the engine will be taken a new engine start cycle.

3. The automatic engine start function at a temperature may be enabled independently of the status of the startup functions of the alarm or periodic launch.

operating Instructions Preparation for remote launch on vehicles with manual gearbox for remote engine start on vehicles with RCPP must be performed by the "software neutral" procedure. The "software neutral" is a certain procedure for the driver's actions, guaranteeing that when the engine is remotely started, the engine will not be installed on the transmission.

Enable software neutral for software neutral

Function 12 tab. 2 must be programmed to one of the ignition support options.

The engine must work depending on the status of the 12 tab function. # 2 1 Inclusion of software neutral can be carried out in the following ways:

- & nbsp- & nbsp-

Remove the key from the ignition cloth.

2 Engine continues to work.

Get out of the car and close all the doors.

3 Turn on the security mode

If the turbotimer mode is not programmed:

- & nbsp- & nbsp-

When arming with the operating engine, the conditions of "software neutral" are also carried out. After the engine work the specified time, it can be running or automatically running.

StarLine B92 Dialog Remote Engine Start by Keychain Before Remote Start Make sure

The hood is closed, and the parking brake is turned on

For a car with a manual box, a "software neutral" procedure

For cars S. automatic box Control lever - in the position "PARK"

Press the key chain 1 for a long time 1 (before the audio signal appears), then the 3 button

- & nbsp- & nbsp-

For one start-up cycle, the system can take 4 attempts to start the engine. If, after the 4th attempt, the engine does not start, then on the display with a feedback keychain (provided that it is in the reception area) will appear "OST", and the keychain will give 4 beeps, indicating the end of the engine start attempts.

Four light signals will follow.

The remaining engine operating time is updated every minute (for example: R10, R09, R08, R07 ...) 1 minute before the engine warming up the engine is displayed and the 2 series of 4 audio signal sounds. After the end time of the engine warming up and its automatic stop, the lights flashed 4 times.

On the display of the keychain briefly displayed R00, 4 audio signal keychain will be performed.

Remote engine stop, if necessary, the engine running automatically or keychain, you can stop at any time:

Press the key chain 1 for a long time, 1 then button 4 short

- & nbsp- & nbsp-

StarLine B92 Dialog Distance Extension of Engine Operation If you need the engine time running automatically or keychain, you can extend:

- & nbsp- & nbsp-

Extend the engine operation unlimited number. The maximum time that can be specified on the keychain by several extension attempts is 30 minutes.

- & nbsp- & nbsp-

Automatic Engine Start Automatic Engine Starting cannot be implemented in the following cases:

Inclusive ignition

The hood is open, the parking brake is turned off (or the foot brake is pressed)

On cars with the RCPP, the procedure of "software neutral"

For cars with a manual transmission, you can activate any of the autorun modes only after performing the program neutral.

Automatic Starting an Alarm Engine to turn on the automatic engine start mode at the set time to alarm clinic:

Check the correct installation of the current time on the keychain

Program the alarm to the desired start time

Turn on the alarm clock (see p.21). The enabled alarm mode on the keychain will be displayed by the icon.

Quick way (see page 24) "Turn on" icon on the display keychain. 1 light signal will follow, a melodic beep sounds and the icon appears on its display, which is displayed in conjunction with the autorun mode on the alarm. For a short time, the installed time of the future startup will be displayed on the display, which will then change for the current time:

Indication of the autorun mode on the alarm clock:

Starline B92 Dialog.

To turn off autorun mode by alarm clock:

Note:

1) The presence of a keychain in the zone of the transceiver at the time of the autorun of the engine over the alarm clinic is not required.

2) The engine start time may differ from the programmed alarm time within 3 minutes.

3) The autorun function on the alarm clock is turned on by one start cycle.

For a new start, you need to activate the autorun from the keychain each time (turn on the icon).

Periodic engine launch (activated with the keychain) The start period (2, 3, 4 or 24 hours) is determined by the programmable function 3 tab. №2. To enable periodic start mode

Quick way (see page 24) "Turn on" icon on the display keychain. 1 light signal will follow, the melodic signal keychain will sound. The display will constantly display the icon that indicates the on-start mode.

Simultaneously with the inclusion of the function, the engine starts and its warming during the programmed time will occur.

To turn off the periodic start mode:

Re-install the cursor on the icon and press the 1 keychain button. Two light signals will follow, a melodic keychain will sound, the icon will disappear.

- & nbsp- & nbsp-

Automatic start of the engine at a temperature (activated with the keychain) alarm allows you to automatically start the engine when registering an external temperature sensor, fixed by the supervision, temperature-adjustable (-5 ° C,

10 ° C, -18 ° Sili-25 ° C, function4Table№2). The engine of the engine is determined by the 2 tab function. №2. Alarm tracks the sensor readings immediately from the moment the function is activated. The minimum interval between repeated autoruns, counted since the previous launch without taking into account the engine warming time - 1 hour. After activating the temperature launch function, the number of motor autoruns by temperature is not limited.

To activate the automatic engine start mode by temperature:

The cursor means (see page 24) "Turn on" the icon on the display of the keychain will follow 1 flash of light signals, the melodic signal keychain will sound. The keyboard display shows an icon indicating the included autorun mode for temperature.

- & nbsp- & nbsp-

To turn off the autorun function for temperature

Set the cursor to the icon and click 2 keychain.

Follow 2 light signals.

A melodic signal keychain will sound, the icon will disappear.

StarLine B92 Dialog Programming Security and Service Functions (Table No. 1) Security and Service Functions, as well as the alarm operation parameters can be changed using the service button and keychain.

The list of functions is given in programming tables.

The programming procedure is described in detail in the signaling instructions.

Refer to the specialists that conducted the alarm installation. Changing programming parameters or reset to factory settings can cause engine lock at regular start, as well as the wrong operation of the standard electrical equipment and alarm itself.

- & nbsp- & nbsp-

The factory settings are highlighted in gray.

StarLine B92 Dialog Elements Elements Keychains and Replacing them

The keychains use the following batches:

Prelkelkesezkdysplaem Used1 element "AAA" 1.5V

WBRELKEBEBEBESCLAYEs Used1Element "CR2450" 3.0V The time of operation of the batteries keychains depends on: frequency of using the keychain, from the selected channel control mode feedback, on the type of power installed.

The capacity of nutrition elements on sale may differ several times.

The average battery life of batteries is:

Forbreckszkdspillem-from6Dery months

For breakboxeszkdisplay-from9Do2 months, when the battery is discharged on the main keyboard display, the icon will be displayed - the power element is needed.

Replacing the power element in the keychain from the LCD

2. Install a new battery element by observing its polarity.

Proper position Power item is indicated on the housing keychain under the lid. Close the keyboard cover.

3. After replacing the power item, adjust the current time reading.

Replacing the power element in the keychain without a housing

1. Slide the battery cover of the keychain and remove the old battery element.

2. Install a new, observing polarity. The correct position of the power item is indicated on the holder contact.
1.32-1.34. We are waiting for further growth. Support level - 1.2750 Resistance level - 1.34 Comment on the long-term picture, ... "a teaching and methodical unite ..." by law of December 27, 2002 No. 184-FZ "On Technical Regulation", and the rules for the application of standards of organizations - GOST P. 1.4 2004 "Standardization in the Russian Federation. Stand ..." Modern materials and systems in construction Methodical instructions To the fulfillment of the laboratory ... "
The materials of this site are posted for familiarization, all rights belong to their authors.
If you disagree with the fact that your material is posted on this site, please email us, we remove it within 1-2 business days.

Security and service signaling functions can be changed using a service button and a keychain without the need to access the central block. The list of functions is shown in the table below.

Programming procedure Next:

When the ignition is turned off, press the service button 5 times.
Turn on the ignition. It will sound 5 sirens signals confirming the input to programming mode.

Press the STARLINE B92 Dialog Flex warning service button to promote the functions from 1 to 16.

Each short press of the service button selects the following function by number. After selecting the function 16, when you click on the button, the system will again go to the programming of the first function.

Long pressing the service button allows you to select functions in the reverse order.

The number of the selected function and its operation mode is displayed on the display of the main keychain, as well as the corresponding flashes of the LED and the signals of the siren. Deciphering Siren and Flash Signals is given in the table Next:

Function	Shut down the service button	Signal Siren and LED
№1	1 time	1 short
№2	2 times	2 short
№3	3 times	3 short
№4	4 times	4 short
№5	5 times	1 Long
№6	6 times	1 long + 1 short
№7	7 times	1 long + 2 short
№8	8 times	1 long + 3 short
№9	9 times	1 long + 4 short
№10	10 times	2 Long
№11	11 times	2 Long + 1 short
№12	12 times	2 long + 2 short
№13	13 times	2 long + 3 short
№14	14 times	2 long + 4 short
№15	15 times	3 long
№16	16 times	3 Long + 1 short

For 15 seconds, press one of the keychain buttons depending on the desired status of the programmable function. The confirmation will follow 1, 2, 3 or 4 sirens and keychain sounds. The programmable function number and the new programmed state will be displayed on the keyboard display. With button 1, two options are selected depending on the type of pressing the button - the short (1st version) or first long, then the short (4th version). Users 2 and 3 are programmed options 2 and 3, respectively.
To exit the auto alarm program mode, turn off the ignition or
Wait for automatic system output. The confirmation will follow
5 flashes of light signals.

Table number 1 Programmable security and service functions StarLine B92 Dialog Flex

Programmable function	Single Pressing Buttons 1.	Single press button 2	Single press button 3	Long + short press button 1
Programmable function	1 signal	2 Signal	3 signals	4 signals
№1 - pulse duration Management locks of doors	0.8 / 0.8 seconds	3.6 / 3.6 sec	double pulse locking 0.8 / 0.8 seconds	comfort 30 / 0.8 sec
№2 - Automatic Managing door locks	claw from pedals Brakes / Revelation from Ignition	from ignition cloud / open (delay 10c)	only leave. from Ignition (delay 10c)	disabled
№3 - Bypassing the salon light and retention of activization Sensors when turned on Security	until shutting down Backlight Salon (60 sec Max.)	without delay	30 seconds	5 sec
№4 - Automatic switching on the protection mode and algorithm for the processing of an additional sensor signals	from locked Castle	from locked Castle	without locking Castle	without locking Castle
	2 levels extra. sensor	two 1- levels extra. Sensor	2 levels extra. sensor	two 1- levels add. Sensor
№5 - Automatic Purchase mode Security	from locked Castle	without locking Castle	Disabled
№6 - Siren confirmation signals	maximum	average	minimum	disabled
№7 - Light indication Open doors	10 seconds	20 seconds	30 seconds	disabled
№8 - Output algorithm Locks when turned on Anti-RAM mode	for Inclusion Torkemose	for Inclusion Anxiety	anti-primilation mode switched off
№9 - Personal PIN - Signaling Code	1-digit factory PIN code \u003d 3	1-digit pin	2-digit pin	3-digit pin
№10 - Activation of outputs on Engine lock	NZ	NR	NZ together with relay R2.	NR together with relay R2.
№11 - 2 step shutdown Engine locks	disabled	included
№12 - Algorithm Additional channel number 4. (blue wire)	1-120 seconds Inclusion Security	1-120 seconds shutting down Security	1-120 seconds incl. and off Security	1-120 seconds shutting down Ignition or Security
№13 - Algorithm additional channel number 1 (yellow-black wire)	0.8 seconds (open trunk)	1-120 seconds (from off shock sensor)	1-120 seconds (without Off Sensor shock)	latch (on / Off keychain)
№14 - algorithm Additional channel №2. (yellow-red wire)	0.8ps (2 steps Dispiration locks)	1-120 seconds (from off shock sensor)	1-120 seconds (without Off Sensor shock)	latch (on / Off keychain)
№15 - algorithm Additional channel number 3. (yellow-white wire)	Pulse 3 seconds after 2 seconds After stopping Engine	Impulse 1 sec 1 seconds After stopping Engine	Duplication Light Signals (Mode 1)	Duplication Light Signals (Mode 2)
№16 - period automatic Channel Control	oFF	3 min	5 minutes	7 min

Silent in the table highlights factory settings.

Attention. Reset to factory settings already installed and operating alarm can lead to impossibility
Remote and automatic engine start, as well as the impossibility of starting the engine in normal mode due to changes in the type of blocking with HP on the NH.

The setting and programming of the Star Line B92 Dialog Flex automotive system can be carried out immediately after the installation of car alarms in the Thazis Orbit Center Tower Center.

Starline

Installation car alarms Starline A2.
Starline A4 car alarm installation
Starline A6 car alarm installation
Installation of car alarms StarLine A8
Starline A9 car alarm installation
Starline B6 car alarm installation
Installation of car alarms Starline B6 Dialog
Installation of car alarms StarLine B6 Dialog CAN F5 V100
Installation of car alarms StarLine B6 Dialog CAN F5 V200
Installation of car alarms StarLine B62 Dialog Flex
Installation of car alarms StarLine B9
Installation of car alarms StarLine B9 Dialog
Installation of auto alarms StarLine B9 Dialog CAN F5 V100
Installation of auto alarms StarLine B9 Dialog CAN F5 V200
Installation of car alarms StarLine B92 Dialog Flex
Installation Instructions (Specifications and Equipment)
Installation, placement and connection guidelines
Connecting various chains
Programming service functions
Description of programmable functions
Programming engine start parameters
Description of programmable engine start functions
Recording codes Brecks
Team tables and batter elements
Operating Instructions (Security and Service Alarm Functions)
Signal control key chains
Setting the functions of the alarm
Programming modes of operation by the cursor way
Turn on the alarm protection modes
Alarms
Power Turning Office
Additional sensors
Anti-primilation mode
Panic Mode
Immobilizer mode
Description of signaling service functions
Turbotimer mode
Remote engine start
Changes in the Starline B92 Dialog alarm functions that appeared in the Flex version (addition to the installation instructions)
Installation of car alarms StarLine B94 Dialog
Installation of car alarms StarLine C4
Installation of auto alarms StarLine C6
Installation of StarLine C9
Starline 24V Agnistation Installation
Installing the Moto V5 Motorization Motorization, Motorcycle Alarms

STARLINE B92 (autorun)
Starline B62.
STARLINE A92 (autorun)
Starline A62.
StarLine B9 Dialog (Autorun)
Starline B6 Dialog.
Starline C9 (autorun)
StarLine C6.
Starline C4.
StarLine B9 (autorun)
StarLine B6.
STARLINE A9 (autorun)
Keychain StarLine B6 / B9
Keychain Starline A8 / A9
Keychain Starline C4 / C6 / C9

StarLine B92 Dialog is a dialogue system for protecting a car with an intelligent autorun function.
New 2010. Reliable automotive security system with dialogue authorization, individual encryption keys, autorun and intelligent autorun function. Designed to work in the conditions of extreme urban interference. It is intended to protect cars of a medium and high price range in the Starline Security Complex "Win".

In the automotive security system, a complete set of security and service functions is implemented, plus:

Dialogue authorization. Dialog code Control with individual encryption keys 128 bits long eliminates intelligent electronic hacking, Sustainable to all existing codegments. To protect the code, the most perfect algorithm for dialog coding is used, as well as an innovative method of jumping frequency. In this method, during the transmission of commands, the specialized transceiver changes the frequencies by a special program in the period of each parcel.
The solution of such a level, known under the technical term "method of expanding the spectrum with a jump-like perestroika frequency," is used for the first time in the world in the system of signaling control system and is a very significant complication of any attempts to hack code.

Mode "Megapolis".Increased range of management and alerts, as well as confident work in the conditions of extreme urban radio interference, is provided by using a 512-channel narrow-band patented transceiver with frequency modulation and a narrow bandwidth. Specialized signals processing program, narrowband filters, as well as optimally distributed from the edges of the frequency range of 433.92 MHz, receiving and transmission channels allowed us to improve the signal-to-noise signal at 8-10 dB and increase the range and noise immunity.

Automatic communication channel control. Provides checking the keychain in the alarm transceiver area and guarantees the alarms from the car. If necessary, you can select the frequency of transmission of signal control signals every 3, 5, 7 minutes or temporarily disable communication control.

Intellectual autorun. Starline B92 Dialog is designed for remote and automatic engine launches. The Special Starline Smart Start interface controls the remote start and operation of any engine. Automatic launches are possible on a predetermined time, with a decrease in temperature below the specified limit, regular periodic. The StarLine B92 Dialog is upgraded by the voltage motor control algorithm, which allows you to reliably register the start of the engine and simplifying installation, allowing in some cases not to search for tachometer or generator signals.

Start / stop button. StarLine B92 Dialog is ideally compatible with cars with start / stop button instead of a standard ignition key.

Ergonomic and reliability keychain. Keychains have innovative design and hidden antenna location. This allows you to increase the reliability of the design of the keychain and implement an ergonomic method of control. In the new 4-button control interface, the principle of the "main button" is applied. Easily detectable Main Button performs the main signaling command - switching on the security mode.

Comfort. The keychains implemented an intuitive principle of management. All pictograms on the key chain in Russian. LED backlight provides a comfortable job with information on the display.

Full protection. Encryption code "Dialog" is used both mainly and in the additional keychain.

Additional functions. Added user battery charge voltage definition functions, viewing alarm history with event time, select the sound volume keychain and selecting ringtones. For the first time in the alarms, it was possible to obtain short confirmation signals on the most ordinary 12 in the sirens.

Advantages for installers:

Upgraded function programming algorithm. Now online on the display keychain can see the function number and its programmed value.
Upgraded control of additional channels allowed to install the StarLine B92 Dialog system on all modern cars.
Digital wireless relays can be connected to enhance anti-theft security starline locks R2.
Starline B62 Dialog models can be easily transformed into a security and search complex by adding one of the GSM / GPS Module Starline, which will be connected to the LAN signaling via one single 3 pin connector.

StarLine B92 Dialog has more than 50 standard and programmable functions provide car owner not only reliable protection, but also comfort when used automotive alarm .

When developing a system Starline B92 Dialog. All the advantages of security systems developed earlier, and factors such as noise immunity and cryptostility of the control signal, the ability to withstand physical overload, working temperature range, convenience and practicality of operation are taken into account.

For each instance, a personal key is generated, the parameters of which are unique. This key is recorded in the alarm unit simultaneously with keychains. The use of such technology provides protection against replacing, algorithmic and other types of grabbbers.

Of course, protection is ensured not only by the key uniqueness. An important value of encryption code and data transfer rate also have. All this prevents attempts to intervene in the dialog exchange between the keychain and the system. Application in the StarLine Dialog series of an eight-channel transceiver and a "fast dialog" code provides systems not only high cryptic resistance, but also excellent noise immunity, as well as increased range and alert.

New features with Flex

Control of the preheater
Automatic folding mirrors
Automatic closure of hatch
"Light" track after the inclusion of the security mode
Automatic seating under the owner
Automatic refund of the steering column to its original position (folding)
Automatic inclusion of low headlights when driving a car (to lower the manual brake, pressing the brake pedal, after autorun, or when starting the engine)
Enable light alarm using a standard alarm controller
Control of additional door lock locks
Disconnection (connection) of additional sensors, power supply to the sensors at the desired time
Additional engine lock (fault imitation)
Opening a trunk with a long-time signaling
Hood Castle Management (Closing)
Additional authorization (connection of immobilizer and opening of the CZ)
Imitation of signals "Intellectual" ignition locks (VW, MERCEDES)
Turning off the janitors, radio at the time of operation of the autorun
Inclusion of heating seats and glass heating during autorun operation
Second pulse to turn off the ignition in case of unsuccessful autorun on push-button cars
Imitation of the second starter signal (with delay)

FEATURES OF AGENDING STARLINE B92 Dialog:

cryptustic signal code " Fast dialogue"(128 bits long) eliminates intelligent electronic hacking
application of individual encryption keys for each system
automatic communication channel control ( every 3, 5, 7 minutes)
mode "Megapolis" (increased control and alert range)
increased speed data transfer rate
car battery charge voltage definitions
viewing alarm history indicating the event time
problem protection signal
shockproof keychain with bilateral communication
ergonomic design and convenience of keychain
antenna module built in keychain
comfortable backlight key fob with LCD
selecting the volume of the sound keychain and the choice of ringtones
an intuitive display
russified display icon designations
large icons
advanced Temperature Range, from - 40 to + 85ºС
full joint work with Satellite Module Starline Messenger GPS
autorun (remote, timer, engine temperature)
turbotaymer

Advantages for installers:

Upgraded function programming algorithm. Now online on the display keychain can see the function number and its programmed value.
Upgraded control of additional channels allowed to install the StarLine B92 Dialog system on all modern cars.
Starline B92 Dialog models can be easily transformed into a security and search complex by adding one of the GSM / GPS of the Starline module, which will be connected to the LAN signaling via one single 3 pin connector.
To enhance anti-theft security, digital wireless lock relays STARLINE R2 can be connected.

Over 50.standard and programmable functions provide car owner not only reliable protection, but also comfort when using the STARLINE Q92 Dialog automotive alarm.

Equipment:

central alarm unit
1 key chain with bilateral connection with LCD
1 key chain with bilateral connection without a LCA
2-level shock sensor
transceiver
hood button
light-emitting diode
service button
wire set
engine temperature sensor
installation Instructions
user's manual
user memo

Automakers

recommend auto alarm
StarLine B92 Dialog Flex for installation on your car

New 2011.Reliable automotive security system with flexible service channels, dialogue authorization, individual keys encryption 128 bits and the function of intelligent autorun. Designed to work in the conditions of extreme urban radio interference. Designed to protect cars of the middle and high price range in the composition security complex Starline "Win."

B Starline has all the best that you can wish, plus:

Dialogue authorization Excludes intelligent electronic hacking and provides sustainability to all known codework workers. To protect the code, the most perfect algorithm for dialog coding with individual encryption keys 128 bits is used, as well as an innovative jumping frequency method. When transmitting commands, the transceiver repeatedly changes the frequencies according to a special program in the period of each parcel. The solution of this level, known under the technical term "method of expanding the spectrum with a jump-shaking frequency restructuring", is used for the first time in the world in the system of signaling control system and is a very significant complication of any attempts to hack the code. Encryption code "Dialog" is used both mainly and in the additional keychain.

Code security is confirmed by a long-term Starline contract for 5,000,000 rubles for specialists in electronic hacking.

Mode "Megapolis".Increased control range and alerts, as well as confident work in the conditions of extreme urban radio domains is provided by using a 512-channel narrowband patented OEM transceiver with frequency modulation. Specialized signals processing program, narrowband filters, as well as reception channels and transmission optimally distributed across the edges of the frequency range of 433.92 MHz allowed us to improve the signal-to-noise signal at 8-10 dB and increase the range of control and alerts 2 times. Forget about radio interfachers on large parking lots.

Automatic communication channel control. Provides checking the keychain in the alarm transceiver area and guarantees the alarms from the car. If necessary, you can select the frequency of transmission of signal control signals to ether each 3, 5, 7 minutes or temporarily disable the control of the communication channel.

Intellectual autorun. Starting and engine warming is made at temperature, alarm clock, time intervals or remote by keychain.

Start / stop button.Starline B92 Dialog Flex is ideally compatible with car start / stop buttons.

Additional functions:

Account control control voltage;
Volume selection and ringing melodies;
Adjusting the volume of sound signals confirmation and disarming.

Heat resistance. Security systems with dialogue protection Starline are developed and manufactured in Russia and are designed to work in a wide range of temperatures from - 45 to +85.

Advantages of StarLine B92 Dialog Flex
Thanks to the flexible service channels, you can implement a number of additional service functions.

Anti-theft functions:
STARLINE FLEX Alarms make it easy to install and implement additional service functions without using external components.

Increase anti-theft functions:

Connecting the digital wireless lock relay STARLINE R2;
Addition GSM / GPS Module Starline using only one connector.

Teams in security and anxiety modes:

Controlling additional door lock locks;
Additional engine lock (malfunction imitation);
Opening the trunk with the shutdown of the standard alarm;
Control of the hood lock (closing);
Enabling light alarm when connected to alarm.

Comfort functions.

Remote control of the preheating heater;
Automatic seat setting under the owner;
Automatic refund of the steering column to its original position (folding);
Automatic inclusion of low headlights when driving a car (to lower the manual brake, pressing the brake pedal).

During auto start: