Advantages: High Efficiency
Disadvantages: practically no
Good day dear readers of the site review about.
In a word, we launch them and bring them to the handle, squeezing the last juices, and then I also demand from them the impossible. Of course, they are patient, but in any case it is necessary to change this approach.
Features of the long-term washing of the engine.
In order to improve the engine operation on your car, I decided to apply a complex drug intended for long-term washing with active protection oil system. This drug is applied for two hundred mileage kilometers before replacing it and helps to improve its circulation and heat sink from engine parts. A distinctive feature this product is the possibility of applying both in gasoline and in diesel aggregates internal combustion. One bottle of substances is designed for two and a half liters of the system.
The tool is absolutely safe for all rubber products, that is, seals, seals, oil supply and compatible with all types of motor oils. Gradually removes all the contaminants formed during the long-term use. It is worth noting that at the same time the system channels do not occur and the more not postponed on their walls, as it is completely evaporated during the work. On the quality and properties of the oil filled into the engine does not have absolutely any influence.
For application this means There are certain prerequisites, which can be fully attributed to such as- significantly contamination of the engine, a significant range of runs before replacing the oil, after use embossed fuel or lubricant, as well as after operation with faulty fuel equipment or low pressure. 
If we talk about the methodology for applying this composition, it should be noted that it is very simple. Initially, it is necessary to carefully shake the bottle and do it in continuous mode during no less than five minutes at temperatures. ambient Not lower than twenty degrees Celsius with a plus sign. After that, pour the composition into the heated to operating temperature The assembly is across the neck. After this procedure, you should run auto and give it to work for twenty minutes in normal mode, then merge the engine oil and replace it with a new one. 
Of course, as well as any chemical composition, the remedy refers to moderately toxic, and as a result, can have a moderate irritating effect when entering skin coatings or a mucous membrane. Therefore, when performing work with it, it is necessary to comply with special precautions and prevent an impact on your body. When contacting the skin, it is necessary to immediately remove it from the surface and rinse first with a stream of clean water, and then warm water with soap. If you get into the eyes, you immediately need to rinse them with plenty of water. If you get into digestive bodies, contact your doctor immediately.
Buy today this species The goods can be almost all specialized stores of our country and, depending on the brand, its cost can be in the range from four hundred to six hundred rubles per vial. As a rule, its volume is three hundred twenty milliliters, although you can meet both smaller and more volume. Of course, with a small difference in price. This product proven himself with the most best side And rightfully enjoys great popularity among motorists. In the market, the company has been present for more than fifteen years and its technology is known far beyond the country.
Video Overview
| All (5) |
|---|
Flushing "Super A-Prokhim" has the following actions:
- Gradually dissolves deposits and contamination in various nodes and engine mechanisms, does not give them to settle again in oil channels, allows you to remove contamination during oil drain. This allows you to facilitate the operation of the engine, effectively clean the oil system when switching from one variety of oil to another, extend the resource of the new oil, which means you will add better defense Engine.
- With constant use (before each oil change), it is possible to gradually dissolve the nap and varnish sediments, formed in the case of overheating of oil, poor-quality combustion of fuel, breakthrough exhaust gases In Carter.
- Cleans piston rings From Nagara, restores their mobility and adherence. Sequential use of flushing for several cycles of engine oil, allows to achieve the effect of rings cutter, especially if their minimal mobility persists. Restoration normal work Piston rings increases and levels compression in cylinders, which is critical for uniform engine operation, full combustion of fuel, and respectively reduce its consumption. Normally functioning piston rings also reduce the likelihood of gase breakthroughs into the engine crankcase, leading to the dilution and oxidation of oil, expanding additives.
- Cleans the hydrocomathers, restores the mobility of the plungers, which leads to the elimination of the characteristic knock when the engine is started and during its operation.
- Effectively cleans the crankcase ventilation system, restores the performance of the PCV valve
- Recommended for continuous use before each oil change.
Long-term flushing "Super A-Prokhem" does not affect rubber-technical and composite products, such as glands and gaskets.
Studied and tested on functional compliance technical parameters russian cars And oils.
Instructions for use
- Heat the engine to operating temperature.
- Mix the contents of the jar, shaking it for 1-2 minutes.
- Fill 1 jar of washing into the oil refining neck. If the volume of the oil system is more than 6 liters, it is necessary to pour 2 washing banks.
- Take a trip by car for 20-25 minutes.
- After 200 kilometers after making the washing, replace the oil and oil filter.
Attention! In case of significant oil pollution in the process of cleaning or sharp reduction in oil pressure (flashing oil pressure lamps) immediately replace the oil and oil filter.
Notes
Precautionary measures:
- Washing agent according to the parameters of acute toxicity according to GOST 12.1007 refers to the third class of danger (moderately dangerous substances). The remedy has a temperate irritant effect on the skin and mucous membranes of the eyes. Volatile components cause moderate irritation of the mucous membranes of the eyes and the upper respiratory tract.
- Use only for destination.
- Do not disassemble and not give to children.
- Do not allow the human body to fall into the eyes and inside.
- Work in a well-ventilated room. Use funds individual protection Skin cover.
- When contacting the skin, remove contaminated clothing. Rinse the exposure to the surface of the body surface of the water stream, and then with water with soap. If you get into the eyes, rinse your eyes with plenty of water. If you get to the digestive organs, consult your doctor.
Notes:
- Store in protected from moisture and direct sunlight place at temperatures from -20 ᵒc to +50 ᵒc.
- Compatible with all types of motor oils.
- Secure for engines of any designs, including turbocharged.
- Evaporates in the process of work. Does not affect properties lubricant oil.
- Safe for rubber seals, seals, masonry Caps;
- Does not score the channels of the oil system and is not postponed on the walls of the elements of the FRO.
Let's start with the fact that the flushing is needed in order to clean the parts and the inner walls of the engine from deposits. What is deposited and what kind they happen, you can read in the article - any deposits in the engine can be considered harmful - sediments in the engine should not be! And in most cases, the engine must be washed.
There are four main engine washing methods.
Method 1. Disassembling the engine and cleaning into manual with washing parts with special means.
You can disassemble the engine to a hundred or familiar in the garage, cleaned every detail with the help of technical solvent (solarium, kerosene, solvent ITD). This method is probably the fastest time and efficient, but also the most time consuming. I do not say that a special room is needed - garage, certain conditions and knowledge. Not every motorist has a warm garage, the ability and skill to disassemble, clean and assemble the internal combustion engine. That is why there are special means for washing the engine, which will be discussed below. It should be noted that there are cases when flushing the engine washes harmful and dangerously, as in general, to run it. Therefore, in some cases, manual engine cleaning is the only option!For example, in such a case:
That is, there is nothing to help here, except to disassemble and manually clean, pass through the wear and the possibility of further use of this engine.
Method 2. Washing oils.
Designed for flushing lubrication systems car engines Without their disassembly, when changing engine oil. Washing oils received tremendous popularity in Russia. In the West in the mind of the mentality "Why will I spend extra money?" Washing oils were not gained great popularity.
Usually wash oil It is the usual mineral, the easiest and cheap oil is mineral water (and why expensive there? Do not ride on it.), To which washing additives, anti-wear additives are added.
Here laboratory analysis Washing oil LUKOIL 
That is, on the analysis we see that anti-wear additives (zinc phosphorus) were added and washes added washing neutralizing additives (calcium). They are added to much less content than in standard engine oils. In fact, this washing in order to mix with the remnable residue of the old oil (in the crankcase as well as the engine parts are still in dirty oil) and neutralize the acid medium in the engine. All this merges along with the washing - here is the main and main goal of washing oil. I'm afraid to wash the dirty engine in a slam or varnish it is not capable ...
The principle of use of washing oils is approximately as follows: The car was brought by 10-20 minutes on idling, pulled the waste motor oil, poured flushing oil in the same filling out What is required by the automaker for engine oil, dried at idle 10-20 minutes, drained the wash oil and poured fresh oil.
In the West, wash oils did not fit and do not share in demand, there you will not see flushing oils (for civilian transport) Mobil, Shell brands, Castrol, etc. (I met BP in Japan) - Manufacturers voiced the standard opinion "When using our engine oils - washing The engine is not required! " And in its manufacturers of motor oils of the right. If you buy new car In the car dealership, change the oil more often (sometimes even more often than requires official dealer), pour good gasoline - The deposits in the engine will not arise! Why spend in empty money? Spend them for ice cream to children! But unfortunately not all new cars, not everyone went clean engineAnd not always the intervals are observed strictly. It is for such cases and there are washing oils.
In Russia, washing oils are presented in a sufficient assortment. Because the demand, in this case, gave rise to an offer. For example, a very serious and large domestic company LUKOIL - does not consider to produce that global manufacturers of engine oils are distrancted. Also on the market presented brands Spectrol, Felix, Novoufim NPZ, HADO VERYLUBE, LUXE, Volga Oil, SibTEK, Unico, Rosneft, G-Energy, ZiCT.
Pour or not pour wash oils - decide for yourself! I decided for myself - that I don't need "money to wind!", And I adhere to the version "at reasonable change intervals - wash oils like washing not needed." But if you, for example, tightened with a change interval or bought a car with an unknown oil change story, washing oil can help remove unsaluable acid residue.
Method 3. Washing of an oil system or "five minutes".
There are also special flushing "five-minute" that are poured into the old oil when changing, the engine is allowed to work 5-10-20 minutes (read the instructions!) And merge along with spent oil. 
Among the motorists in the Internet community, the opinion is generally accepted - "Washing" Five minutes "- evil!" On the forums there are horror stories that "Five minutes wash the slices that fall off, scoring oil canals, clog the filter, the grid of the oil worker and the engine fails! " "The five-minute pernicious effect on gaskets and glands - and after washing the engine necessarily" run "" "Five minutes are not compatible with your future oil, they remain in the crankcase with the unsolved residue and spoil the next oil, as well as your engine.". I will not argue with these statements, especially since when it possessed the same opinion, I just show it clearly and conclude the reader to the conclusion. See all yourself and with your own eyes!
Again, we ask the question, and somebody from manufacturers of motor oils makes five minutes? There is a shell, valvoline, Wynn's, Liqui Moly, Motul - that is, some manufacturers pay attention to the demand of motorists, in a particular country, all the same produce five minutes. I spent two visual experiments with flushing two well-known and sufficiently respected brands. Liqui Moly. and Motul.
I spent two visual experiments with flushing two well-known and sufficiently respected brands. Liqui Moly. and Motul.
Experiment 1. Flushing "10-minute" (German name Liqui Moly Pro-Line Motorspulung).
Car Toyota Curren 1994 release, with 3S-Fe engine. The engine inside is very dirty - deposits like varnish and sludge. Open valve cover, take pictures under the valve lid - BEFORE. Then we go with short change intervals, applying a fifth minute wash between shifts LIQUI MOLY PRO-LINE ENGINE FLUSH. With this procedure, strictly follow the instructions on the bank. If it is said "10 minutes on idling Motor "then do it - this is important!
This amateur experiment nevertheless stretched from me exactly 1 year. Mode is mostly urban traffic jams and a little track. Motor oil used normal for gasoline engines With API SM North American Petro-Canada Supreme 5W-30 and Chevron Supreme 5W-30 (in common semi-synthetic, but on the fact of mineral water 2 groups API.). Gasoline used one and the same with one refueling.
In this case, the interval between the shifts of 1500-2000km is not randomly chosen - for the speed of experiment and smaller effect on the experiment of the engine oil itself. 5 flushing of the oil system of the engine was carried out - 5 cans left. We open the engine and photograph the result
Expether 2. Flushing 15 minutes Motul Engine Clean.
The car is the same Toyota Curren 94 release, 3S-FE engine. The mode is also a city of 80% and a 20% route.
5 shifts were produced, 5 washing cans were used.
Toyota 5W30 SM + Motul Engine Clean \u003d 3000km
Petro-Canada Supreme 5W30 SM + Motul Engine Clean \u003d 3000km
Petro-Canada Duron Synthetic 0W30 + Motul Engine Clean \u003d 3000km
Mobil1 0W40 Life + Motul Engine Clean \u003d 3000km
Petro-Canada Supreme 5W30 SM + Motul Engine Clean \u003d 1000km
Comparing photos BEFORE And you can make certain conclusions about the efficiency of washing the oil system.
The reader may have doubt "What is the oil filter? After all, score! " As the opening of each filter showed after each washing - inside they were clean - there were no serious savings!
And how does the engine feel after such flushing? Excellent! Nothing would have run anywhere and did not break - there was already enough time. Moreover! I made a laboratory analysis of engine oil on the content of wear metals - the engine showed near zero wear.
Another example of another protein forum staff. Video where it is clearly shown as washing the washing "Five minutes". Opened the engine, saw deposits, collected back washed with 15-minute washing according to the instructions, and opened to see "What has changed?" And nothing has changed! This is not a miraculous flushing. In general, see the roller:
Method 4. Flushing with engine oil - as the most tender flushing.
There is also a washing of the oil system by the usual motor Oil - at which exactly nothing will happen. This flushing will be compatible with your engine, glazed gaskets, your future Oil ITD.
The method is very simple: pour your usual engine oil or cheap mineral water, which you usually prefer the brand (whatever money), rolled on this oil 500-1000km and merged. That's all! Just in case, you can change the oil filter. But there is one big but! Engine oil has a very low detergent! In fact, it can only take part of the particles that have already been pulled off from the walls - and the engine as dirty will remain so - either you need a lot of time and thousand km on the principle of "water stone sharpening." You can figure this stone and 500 thousand km - which reduces the engine washing with oil. Do not think that you poured the oil, roll back 1000km and everything inside you inside. If the deposits are really serious - everything will remain as well as it was! Washing with engine oil, I dedicated a separate article, since I have many years of experience - put such experiments.
Output
And so we listed the 4 main methods of washing the oil system. The most important thing is to solve for yourself, should I wash the engine?
Take a flashlight, unscrew the lid of the oil-tank neck, look inside (and it is better to remove the valve cover). If there is a pure metal - then you have a clean engine and most likely no flushing you need. The walls of the neck - this is the same inner wall of the engine as everyone else, besides at the very top. Remember - washing must have a reason! 
First, put the diagnosis and are responsible for: engine dirty or pure? And then decide to treat or leave as it is!
Wash washing a clean engine "for the sake of prevention" does not make sense! You spend money ... It is better and more efficient in this case to change the oil not through 10 000km, but after 7500km! Clean engine will feel much better than 10 thousand km with flushing!
