Ford Mondeo. – executive sedan. business class, also known in the body wagon and five-door hatchback. At the initial stages of production was considered relatively compact modelmanufactured since 1993. The car has gained high popularity in the European market - largely due to the low price, practicality, rich set of options and powerful motors. It is noteworthy that Ford Mondeo was sold in North America called Ford Contour and Mercury Mistique. In a constructive and design plan, the car did not differ from european versionand it was not optimized for the requests and preferences of the Americans (there is due to the types of packages, a set of equipment, engines T.S.). In this regard, Mondeo in the United States turned out to be an unprofitable model, and after 2000 sales stopped. After a while the car for North America Renamed B. FORD FUSION.who should not be confused with the hatchbeck of the platform Ford Fiesta.. In addition, American Fusion finally adapted to requests from the local market. After that, sales increased significantly.
In 2007. ford. introduced absolutely new Mondeo.. Car fourth generation It became much more than its predecessors. The newer Mondeo is now positioned as a D-class car. Its length is 4844 mm, and the width is 1886 mm, which was then a record indicator in the class.
How much oil is pouring into Ford Mondeo automatic transmission
Since 2012, the Ford Mondeo / Fusion has begun to sell in the United States, which is a deeply modernized version of the fourth Mondeo. After a few years, sales managed to master in Europe and Russia.
The car received four configurations and two gasoline engines - 2.5 and 2.0 liters. The power of the first motor is 149 liters. s., and the second - 199 and 240 liters. with. Depending on the modification.
Ford Mondeo 4 Replacing Oil in a manual transmission or working fluid in an automatic transmission
The design of the gearboxes does not provide for oil replacement ( working fluid) During the entire service life of the car. However, sometimes the need to replace the oil (working fluid) may occur, for example, when switching to oil of other viscosity, when repairing the gearbox, etc.). Useful advice. Weight oil (liquid) recommended for 15 Min after a trip until it has cooled and has good fluidity.
Oil in a manual gearbox mod. IB5 is merged as follows. You will need: the end heads "on 8", "on 19", the key hexagon "on 8", the syringe, a wide capacity for oil drain. Use the oil, the oil recommended by the manufacturer in the manufacturer in the specification Ford. With its absence as a substitute, you can use Castrol or Mobil Class Transmission Oils quality API GL-4/5 SAE 80W-90. If the car is exploited for a long time at ambient temperature below -30 ° C, we recommend replacing the oil-filled transmission oil sAE oil 75W. (See Removing and installing mudguard and protect engine crankcase).
2. Remove the gearbox cover of the gear mechanism (see Replacing the Transmission Control Cables).
3. We recommend to remove the gear shift mechanism casing, since the oil drained from the gearbox will spread inside the casing and then, pouring out of it, pollute the working area. To do this, remove the three bolts of the casing fastening and remove it. Use. In the presence of fixtures for collecting the flowing oil (for example, a figure funnel) the gear mechanism casing can not be removed.
4. Remove the base hole tube ...
5 .... Previously substituting the container under the hole, and drain oil into it. Wait when the oil is completely completely (at least 15 minutes), and wrap the plug. Use.
A magnet is installed on the oil pipe stopper (a magnet is installed (shown in the photo by the arrow). Look at it and clean from sticking metal particles and contaminants. The presence of a large amount of metal particles on a magnet is indirectly indicates any malfunction of the gearbox. In this case, check and refrank the box if necessary. Watch the oil dripping and install the gear shift mechanism housing (if it was shot).
7. Remove the jacket of the oil-operated hole ...
8 .... And fill the oil into the gearbox to the lower edge of the oil-teller (the oil will begin to flow out of the hole) .9. Remove the rags of the oil drums and wrap the oil-free stopper. Install the shift mechanism cover, the mudguard and the engine crankcase protection.
Oil B. mechanical boxes Mode gear. MTX-75, MMT6 and MT-66 Replace as follows. Primesters. We are in the gearbox oil recommended by the manufacturer for the Ford specification. In its absence, it can be used as a substitute for the Castrol or Mobil quality class API class API GL-4/5 SAE 75W-80. If the car is exploited for a long time at ambient temperature below -30 ° C, we recommend replacing the oil-filled oil in the factory transmission oil SAE 75W.1. Remove the mudguard and protect the engine crankcase if it is presence (see Removing and installing the mudguard and protect the engine crankcase).
2. Remove the plug and the oilflip opening, pre-substituting the container under the hole, and drain the oil into it. Wait for the oil completely (at least 15 minutes), and wrap the plug.3. Remove the plug used the oil hole and fill the oil into the gearbox to the lower edge of the oil-filling opening (the oil will begin to flow out of the hole) .4. Remove the rags of oil drums and wrap the oil-tape hole.
To replace the working fluid in automatic box Mode gear. AWF21 Perform the following operations. Use. Will with a transmission fluid recommended by the Ford Plant Manufacturer. With it, it can be used as a substitute Mobil ATF 3309 quality class JWS.1 class. Remove the mudguard and protect the engine crankcase if it is presence (see Removing and installing the mudguard and protect the engine crankcase).
2. Remove the plug hole, pre-substituting the container under the opening, and drain the liquid into it. Wait when the liquid is completely solved (at least 15 minutes), and wrap the plug.3. Remove the air filter (see Removal and Installation air filter and muffler inlet noise).
4. Remove the plug of the bulk hole and fill the liquid.5. Let the engine and warm the working fluid.
6. With the engine running, remove the fluid level pointer in an automatic transmission ...
7 .... And check the level. It must be in the middle of the tip of the probe, in the risk area (shown in the photo by the arrow) .8. Install all the details taken in the reverse order.
Replacing oil in a manual transmission or working fluid in the Ford Mondeo 4 automatic transmission (2007-2014)
ford-mondeo-4.dv13.ru.
Replacing Oil in the manual transmission and automatic transformation of Ford Mondeo
The design of the gearboxes does not provide for the oil replacement (working fluid) during the entire service life of the car, however, sometimes the need to replace the oil (working fluid) may occur, for example, when switching to other viscosity oil, when repairing the gearbox, etc.).Oil in a manual gearbox mod. IB5 is poured as follows.
You will need: the end heads "on 8", "on 19", the key hexagon "on 8", the syringe, a wide capacity for draining oil.
1. Remove the mudguard and protection of the engine crankcase when presented
2. Cover the cover of the gear mechanism 
3. We recommend removing the gear gear mechanism cover, since the oil drained from the gearbox will spread inside the casing and then, pouring out of it, contaminate the working area to do so remove the three casing fastening bolts and remove it. 4. Start the oil plug
5. Pre-substituting the container under the hole, and drain oil into it. Wait for the oil completely (at least 15 minutes), and wrap the plug
A magnet is installed on the oil plug plug (shown in the photo by arrow). Inspect it and clean from the stuck metal particles and pollution. The presence on the magnet of a large amount of metal particles indirectly indicates any malfunction of the gearbox. In this case, check and, if necessary, repaired the box. 6. Validity by the rag of oil drums and install the gear shift mechanism (if it was filmed).
7. Remove the tube of the oil hole ..
8. Fill oil into the gearbox to the bottom edge of the oil-teller (the oil will begin to flow out of the hole).
9. Adjust the winds of the oil and wrap the tube of the oil-free hole.
10. Install the gem shift cover cover, mudguard and engine crankcase protection.
Oil in mechanical box gearboxes. MTX-75, MMT6 and MT-66 replace as follows.
If the car is exploited for a long time at ambient temperature below -30 ° C, we recommend replacing the SAE 75W transmission oil at the factory.
1. Remove the mudguard and protection of the engine crankcase when presented
2. Aclude a plug of oil-solenoid hole, pre-substituting the container under the opening, and drain the oil into it. Wait for the oil completely (at least 15 minutes), and wrap the plug 3. Machine the plug used the oil hole and fill the oil into the gearbox to the lower edge of the oil-filling opening (the oil will begin to flow out of the hole).
4. Adjust the winds of the oil and wrap the tube of the oil-filling hole.
To replace the working fluid in the automatic transmission of modes. AWF21 Perform the following operations.
1. Remove the mudguard and protection of the engine crankcase when presented
2. Aclude the plug plug, pre-substituting the container under the opening, and drain the liquid into it. Wait when the liquid is solved completely (at least 15 minutes), and wrap the tube
3. Cut the air filter 4. Start the plug of bulk hole and fill the liquid.
5. Let the engine and warm the working fluid.
b.Prie running engine Remove the fluid level pointer in an automatic transmission.
7. Check the level. He must be in the middle of the tip of the probe, in the risks area (shown in the photo by the arrow). 8. Install all the details taken in the reverse order.
www.fordclubrus.ru.
It is time to replace the oil in the Ford Mondeo gearbox. Looking ahead, I will say that I really liked Valvolin, and in the laying moth disappointed ... In principle, everything is simple, especially if the engine protection you do not have the only thing that will need this syringe for fill oil In a box or device such as I built.
Work on the replacement of oil in the MTX-75 box on Valvoline Max Live 75W-90 in Ford Mondeo
drain plug. Inner hexagon.
drain plug
Device
We merge the oil through drain plug, hot. It is desirable to lift the left side so that more oil merged. After wrap a drain plug and turn the bulk. By the way? they are the same. Pour oil, in my case, through the device. We bring the bottle B. motor compartment To the top bottom, while inserting the hose into the bulk neck after davir on the bottle to make the oil quickly merged. Periodically turn the bottle so that the fusion oil is compensated by air. I left two with a small liter of oil.
That's all! The effect after replacing is positive.
https://www.drive2.ru/l/2426063/
next article:
6:915 9982
Tags: gear
Posted
Liked
www.spike.su.
Ford Mondeo | The frequency of replacement of operational liquids, lubricants
1.5. The frequency of replacement of operational liquids, lubricants
| General |
Motor oil must be replaced every 10,000 km of run. The new car needs to replace the oil after the end of the run (in 2500 km). When replacing the oil, you must install a new one oil filter (ZMZ-4062 engine) or its filter element (all engines). For the procedure for replacing the oil, see subsections 2.3.2, 2.3.2.2 and 2.3.3.3.
In the engine crankcase, it is recommended to pour the oil of the same brand as in the engine. If the oil is poured another brand, you need to pre-rinse the engine lubrication system with oil of the brand, which will be flooded into the engine. To do this, merge the old oil, pour a new oil by 2-4 mm above the tag "0" on the index (probe) of the oil level. Run the engine and give it to work on idling About 10 min. Then drain the oil, replace the oil filter or its filter element and pour fresh oil.
Cooling fluid must be changed once every 2 years or through 60,000 km of run (depending on what comes before). For the procedure for replacing the coolant, see subsection 2.4.4. It should be borne in mind that the coolant liquid is poisonous, therefore it is impossible to suck it with its mouth when overflowing. When working with coolant, it is recommended to use protective glasses, do not smoke and do not eat. If the liquid fell into open areas of the skin, rinse them with water with soap.
Oil in the gearbox must be replaced after 60,000 km run. For the procedure for replacing the oil, see subsections 3.3.2 and 3.4.2. Every 20,000 km of mileage, you need to check the oil level in the gearbox and should be addressed if necessary. The oil level in the box crankcase must reach the edge of the bulk hole. If there is metal particles in a fusion of oil or it is very dirty, you should rinse the box. To do this, pour 0.9 l of fresh oil into its carter. Raise jack back the back of the car. Run the engine and turning on the first transmission, give it to work 2-3 minutes. Then drain the oil and pour fresh. When checking the oil level, it is necessary to clean the surface of the sapunion from the dirt and turn it several times its cap to remove the dirt under it.
Carter oil rear bridge It is necessary to change through 60,000 km run. The oil is replaced in the same way as in the gearbox. After 20,000 km of mileage, you need to check the oil level in the crankcase and should be addressed if necessary. The oil level should reach the edge of the bulk hole. When checking the oil level, you need to clean the sapun from dirt as well as it was done for the gearbox.
Warning
Use re-merged brake fluid is prohibited.
Brake fluid in clutch and brake drives must be changed once every 2 years regardless of the car's mileage. Brake fluids are used in the clutch and brake drives domestic production "Rosa", "Rosa-3", "Tom", "Neva" or their foreign analogs On non-oil basis, the quality level of which is not lower than DOT-3. Use liquids of other brands, especially oil based liquids, is prohibited.
Brake fluid is hygroscopic, so it can not be stored in an open container.
The procedure for replacing the brake fluid is as follows:
1. Remove the main cylinder brake tank cover.
2. Remove the rubber protective caps from air outlet valves on the wheeled cylinders and put on the valves rubber hoses, the ends of which are lowered into glass vessels.
3. Release valves for no more than one turn and by pressing the brake pedal until it stops, drain the liquid. As the fluid leaks stops from the hoses to fade the air output valves.
4. Pour from vessels to merge the brake fluid and put them in place.
5. Pour fresh liquid into the main cylinder tank, unscrew all air output valves per revolution and, pressing the brake pedal until it stops, fill the brake system. At the same time, it is necessary to constantly fill the liquid into the main cylinder tank. After from the hoses, put on the air intake valves, will begin to flow clean brake fluid, Wrap the valves.
6. Purpose the brake system to remove air from it (see subsection 6.9).
7. Close the cork tank the main cylinder of the brake. Remove hoses from air outlet valves and put protective caps on them.
In the same way, the fluid in the clutch hydraulic drive is replaced.
autumn.ru.
Where the oil is poured into the manual transmission on Ford Mondeo 4
Replacing Oil MCPP Ford Focus. 2
replacing the Ford Mondeo oil with your own hands
Ford Focus 1.8l. Zhor Oil? There is a solution! (Personal experience)
replacing oil in the manual transmission on Ford Focus 2
How to pour oil into the box
drain / Oil Replacement in MCPP Ford Mondeo 3
Ford Focus 3 Replacing Oil In Engine
Replacing Oil MCP FORD FUSION 1.6I
How to check the oil level in the engine and the box (tips from the RDM import)
Replacing oil in a mechanical box Ford Focus 2
Also see:
- What is the foreman on the front fog lights Ford Focus 2.
- Rubber sizes for Ford Cuga 2014
- Remkomplekt TNVD Bosch. Ford Transit.
- Auto Ford Focus 3 automatic transmission
- Ford Mondeo Rear Salt Plocks
- Ford Escort Front Wheel Hub 1986
- Disassembly Ford Transit 1996
- Ford Transit 2015. new Body
- Citroen C4 2011 or Ford Fusion
- Ford Explorer. 2004 Fuel consumption
- Steering column FORD FUSION.
- Electroshem Ford Focus 2 2006
- Ford Mondeo 2015. horsepower
- Peugeot Partner. TEPEE and FORD.
- Ford Mondeo smoke blue smoke
fordport.ru.
Ford Mondeo | Replacing the oil in the gearbox
8.1.2. Replacing the oil in the gearbox
| General |
| Order procedure | ||||||||||||||||||
|
||||||||||||||||||
autumn.ru.
The replacement of the box of the box requires a drain of oil, so before replacing the KPP Ford Mondeo 4, it is necessary to warm up the engine to the operating temperature so that the oil becomes more liquid. Further, everything is like when replacing transmission oil ...
- Drive the car by watching pit, put on the handbrake.
- Under the wheels it is desirable to set the stops or anti-digit wedges.
- Since we will change the left-wheel drive seal, then you need to remove the left wheel.
- Drug and raise the left side of the car and remove the wheel.
- Next, remove the ceter protection if it is available.
- Hexagon, unscrew the drain plug, it is located on the crankcase of the box on the right side, after setting a liter capacity for a drain hole to 5.
8. While the oil drains, treat the finger of the ball left wheel and the steering pin with the WD-40 liquid.
9. Now try unscrew the ball of the ball support, and after the tip of the steering thrust.
10. Using the "VAZ" puller, make the tip of the steering wheel from the swivel fist.
11. When tie Rod It will be removed, turn the wheel hub to the right in order to access the ball.
12. After partial flip of the finger of the ball support, do not rush to immediately remove it rounded fistBefore that, using the head to "13", unscrew the drive bolt in the hub.
- Glass oil. Now using a wooden spike, you need to knock out the drive from the hub inside the maximum.
- When the drive comes out of the hub, install the mount over the lever, the openers of it into the subframe, lower the lever down. Thus, you will remove a swivel fist with a ball support.
- Now that the fist is removed, remove the rack to the side closer to the front bumper. Stick the drive so as not to jump out of the inner shrus.
- Take a melancholy again and once again score the drive inside, then turning the wheel to the right, get the drive from the hub and put it on the lever.
- Go down to the pit, set the mount between the external rope of the inner screw and the wall of the box and try to push it out of the box as if the lever. There must be two clicks, first pops up the locking ring, then the entire shank drops out of the slots.
18. Now you have to tinker, the gland is not so simple. Personally, I had problems with this, so I had to get it on slices.
19. After got old gland, lubricate a new gland boxes Ford. Mondeo 4 with transmission oil and set into the hole. In order for him to get into place had to use a copper.
Further assembly is made in reverse sequence. Here is the entire replacement of the seal of the PPP Ford Mondeo 4 with their own hands. Difficult little, slowly with the "smoke" work under the power to fulfill anyone. I wish good luck in your work!
Thank you for visited by: Ford Master
The design of the gearboxes does not provide for the replacement of oil (working fluid) over the entire service life of the car.
However, sometimes the need to replace oil (working fluid) may occur, for example, when switching to other viscosity oil, when repairing the gearbox, etc.).
Useful advice: Mix the oil (liquid) is recommended for 15 minutes after the trip until it has cooled and has good fluidity.
Oil B. manual gearbox mod. IB5 merged as follows.
You will need: the end heads "on 8", "on 19", the key hexagon "on 8", the syringe, a wide capacity for draining oil.
NOTE: Pour the gearbox oil recommended by the Ford Plant Manufacturer. With its absence as a substitute, you can use Castrol or Mobil Class API GL-4/5 SAE 80W-90 quality transmission oils.
2. Remove the gearbox cover of the gear mechanism ().
3. We recommend to remove the gear shift mechanism casing, since the oil drained from the gearbox will spread inside the casing and then, pouring out of it, pollute the working area. To do this, turn out three casing fastening bolts and remove it.
Note: If there is a device for collecting flowing oil (for example, a curly funnel), the gear shift mechanism can not be removed.
4. Remove the base hole tube ...
5 .... Previously substituting the container under the hole, and drain oil into it. Wait when the oil is completely completely (at least 15 minutes), and wrap the plug.
Note: A magnet is installed on the oil skylight stopper (shown in the photo by arrow).
Inspect it and clean from the stuck metal particles and pollution. The presence on the magnet of a large amount of metal particles indirectly indicates any malfunction of the gearbox.
In this case, check and, if necessary, repaired the box.
6. Wash the winding of the oil and install the gear shift mechanism housing (if it was filmed).
7. Remove the jacket of the oil-operated hole ...
8 .... And fill the oil into the gearbox to the bottom edge of the oil-filling opening (the oil will begin to flow out of the hole).
9. Remove the rags of the oil drums and wrap the oil-tape hole.
10. Install the shift mechanism cover, the mudguard and the engine crankcase protection.
Oil B. mechanical gearboxes mod. MTX-75, MMT6 and MT-66replace as follows.
NOTE: Pour the gearbox oil recommended by the Ford Plant Manufacturer. In its absence, it can be used as a substitute Castrol or Mobil quality class API GL-4/5 SAE 75W-80.
Note: If the car is exploited for a long time at ambient temperature below -30 ° C, we recommend replacing the SAE 75W transmission oil at the factory.
1. Remove the mudguard and protect the engine crankcase if it is presence ().
2. Remove the plug and the oilflip opening, pre-substituting the container under the hole, and drain the oil into it. Wait when the oil is completely completely (at least 15 minutes), and wrap the plug.
3. Remove the plug used the oil hole and fill the oil into the gearbox to the lower edge of the oil-telny hole (the oil will begin to flow out of the hole).
4. Remove the rags of oil drums and wrap the oil-free stopper.
To replace the working fluid in automatic gearbox mod. AWF21. Perform the following operations.
Note: Pour into the gearbox The liquid recommended by the Ford Plant Manufacturer. With it, it can be used as a substitute Mobil ATF 3309 quality class of JWS.
1. Remove the mudguard and protect the engine crankcase if it is presence (
7 .... And check the level. He must be in the middle of the tip of the probe, in the risks area (shown in the photo by the arrow).
8. Install all the details taken in the reverse order.
The design of the gearboxes does not predict the change of oil (workwater) throughout the entire life of the car, but from time to time the need to change the oil (workwater) occurs, for example, when moving to oil of other viscosity, when performing the repair of the box, etc.).
Butter in a manual box mod. IB5 is drained in this way.
For you, you will need: the end heads "on 8", "at 19", the key hexagon "on 8", the syringe, a wide container for draining oil.
3.2.Clit gear cover of gear mechanism
3. Sinking to remove the gear shift mechanism casing, because the oil plums from the box will break off the cover of the casing and later, pouring out with its use, pollute the work area for this purpose to unscrew the three casing fastening bolts and remove it.
4. Shut the oil plug
5. For a previously substituting the container under the hole, and drain the oil there. Wait when oil connects quite (two or more than 15 minutes), and wrap the plug
A magnet is installed on the oil plug plug (shown in the photo by arrow). Inspect it and clean it from stuck iron particles and pollution. The presence of the magnet mass of iron particles indirectly shows on any malfunction of the box. Under such circumstances, check and, if desired, repaired the box.
Changing Oil B. mCPP
Repair Assistance in the auto electrician service !!!
Ford Mondeo 4 Faithful seplace of the semi-axis (Specotter)!
Here video you can learn how without the help of others change oil in a manual box. on the ford Mondeo .
6. Validity by the rag of oil drums and install the gear shift mechanism (if it was filmed).
7. Remove the oil-tape plug.
8. Fill the oil in the checkpoint to either the top edge of the oil-filling opening (the oil will begin to flow out of the opening).
9. Dowse the winds of the oil and wrap the tube oil opening.
10. Install the gearbox cover of the gear mechanism, the mudguard and the motor crankcase protection.
Oil in mechanical box boxes. MTX-75, MMT6 and MT-66 Speake so.
If the car is highly exploited at ambient temperature below. 30 ° C, we advise you to change the SAE 75W transmission oil in the factory.
1. Remove the mudguard and protect the motor crankcase when it is
4. Hold the cork and the oil-plug-in hole, for previously substituting the container under the hole, and drain the oil there. Wait when butter connect completely (two or more than 15 minutes), and wrap the plug
3. Hold the cork B. oil opening and fill the oil in the checkpoint to one of the edges oil opening (Butter will begin to flow out of the hole).
4. Adjust the rags of oil drips and wrap a plug Oil opening.
To change the workwater in the automatic box mod. AWF21 Make subsequent operations.
1. Remove the mudguard and protect the motor crankcase when it is
5. Hold the plug hole, for previously substituting the container, and drain the fluid there. Wait when the fluid connects one hundred percent (more than 15 minutes), and wrap a plug
3. Cut the air filter
4. Hold the plug of the bulk hole and fill the fluid.
5. Let the engine and warm the working fluid.
b.Prie running engine pull out the water level pointer in the automatic box.
7. Check the level. It must be in the center of the tip of the probe, in the area of \u200b\u200bdanger (shown in the photo by the arrow).
8. Install our client remains removed from the order of working capital.
.. 150 151 159 ..
Ford Mondeo 4. Replacing the oil in a manual transmission or working fluid in an automatic transmission
The design of the gearboxes does not provide for the replacement of oil (working fluid) over the entire service life of the car. However, sometimes the need to replace oil (working fluid) may occur, for example, when switching to other viscosity oil, when repairing the gearbox, etc.).
USEFUL ADVICE
Oil in a manual gearbox mod. IB5 is poured as follows.
You will need: the end heads "on 8", "on 19", the key hexagon "on 8", the syringe, a wide capacity for draining oil.
Notes
If the car is exploited for a long time at ambient temperature below -30 ° C, we recommend replacing the SAE75W transmission oil in the factory.
1. Remove the mudguard and protect the engine crankcase if it is presence (see "Removing and installing the mudguard and protection of the engine crankcase", p. 75).
2. Remove the gear cover of the gear mechanism (see "Replacing the gearbox control cables", p. 153).
3, we recommend removing the gear shift mechanism housing, since the oil drained from the gearbox will be spread inside the casing and then, pouring out of it, pollute the working area, to do the three casing fastening bolts and remove it.
NOTE
In the presence of a device for collecting flowing oil (for example, a figure of the Ronki), the shift mechanism casing can not be removed.
A magnet is installed on the oil plug plug (shown in the photo by arrow). Inspect it and clean from the stuck metal particles and pollution. The presence on the magnet of a large amount of metal particles indirectly indicates which "or malfunction of the gearbox. In this case, check and, if necessary, repaired the box.
6. Wash the winding of the oil and install the gear shift mechanism housing (if it was filmed).
7, remove the jacket of the oil hole ...
8. ... and pour the oil into the gearbox to the lower edge of the oil-teller (the oil will begin to flow out of the hole).
9. Remove the rags of the oil drums and wrap the oil-tape hole.
10. Install the shift mechanism cover, the mudguard and the engine crankcase protection.
Oil in mechanical box gearboxes. MTH-75, MMTB and MT-66 replace as follows.
Notes
