Proper care is a pledge of reliable and long service Any car. Ford Focus 2 has not exceeded. If it is timely maintenance, then there will be no problems with it.
Oil change - an important procedure. As a rule, it is carried out according to the regulations, which installed the manufacturer. Getting acquainted with his recommendations will help the instruction manual. But it is worth noting that this information is not accurate. Since in practice under the influence of negative factors, oil is much faster comes to unsuitability. It is necessary to immediately change the liquid. This will prevent premature wear of parts.
In addition, not to harm the car, you need to know how much and what to pour into different aggregates or nodes. And no matter the procedure is performed by its own or specialists. In the second case of knowledge filling volumes And the names of materials, liquids will help to avoid deception. Below is a table that contains the necessary information how much oil and liquids are pouring.
What oil and how many liquids fill in the Ford Focus of the 2nd Generation
| Place refueling / lubrication | Volume of refueling, l. | Oil / fluid name | |
| Fuel tank | 55 | Neeterized automotive gasoline AI-95 | |
| Engine lubrication system, taking into account the oil filter: | 4,3 | Motor oil Ford or Motorcraft Formula E with class sAE viscosity 5W30, corresponding requirements for Ford. WSS-M2C913-B. Ford allows the use of motor oils of other manufacturers, with SAE 5W30 viscosity class and meets the requirements Ford WSS-M2C913-B; ASEA A1 / B1; SJ / CF API |
|
| Engine cooling system, including a salon heating system: | 6.5 (1.8 Duratec) 6.3 (2.0 DURATEC) |
MotorCraft SuperPlus 2000 Cooling fluid, complying with Ford WSS-M97B44-D requirements | |
| Mechanical box Transmissions | 2,3 | Transmission oil Ford SAE 75W90 WCD-M2C200-C | |
| Automatic box Transmissions | 5,0 | Transmission liquid ATF. Ford Merkon V. | |
| Hydraulic brakes and clutch | Till Max Tags 1.25-1.35 liters |
Brake fluid DOT-4, DOT-5 Original - WSS-M6C57-A2 |
|
| Steering Amplifier (GUR) | Till Max Tags 0.9-1 liters |
Working fluid corresponding to the requirements of Ford WSA-M2C 195-A MOTORCRAFT MERCON LV XT10QLVC |
|
| Tank washer glass | with fleeves of the heads | Watering fluid with an appropriate freezing temperature | |
| no fleevers flew | |||
Oil volume and liquids of fuels Ford Focus 2 Was Last Modified: May 28th, 2019 by Administrator.
In the Manual Ford Focus 2, it is written that the engine can be replaced in the engine with a periodicity of 20,000 km (no less often). If the machine is operated in heavy conditions, for example, in dusty terrain or in a metropolis, oil replacement should be made every 15,000 times, and better every 10,000 km.
How many engine oil is necessary to replace?
The required volume of engine oil depends on the volume of the engine:
- For diesel engine, 1.8 - 5.6 liters.
- For gasoline engines, 1.4 l - 3.8 liters.
- For engines, 1.6 l - 4.1 liters.
- For engines, 1.8 l and 2.0 - 4.3 liters.
For engines, Focus 2 is suitable for a Formula F 5W30 branded engine oil. The manufacturer also admits the use of other Motor oils having the SAE 5W30 viscosity class and the corresponding Ford requirements, namely API CF and SJ, ACEA A1 and B1, including WSS-M2C913-B.
As for the oil filter, you need to consider the type of engine of your car. So, on diesel enginesThis item has a type of cartridge. While on gasoline engine, the oil purification filter is made in the form of a glass.
How to change engine oil
To replace the oil, it is necessary to prepare the key to "thirteen", new filter, Tar for draining the working fluid, as well as a puller, the day of removing the old oil filter. In the absence of the latter, you can use a screwdriver or leather belt. An important point is the choice of place to perform work. It may be looking Yama or overpass.
See below the video "Replacing an oil on Ford Focus 2, with engine 1.8".
In the case of transition to another brand of engine oil, a complete flushing of the system is recommended. Otherwise, "conflict" of additives and reducing the effectiveness of the working fluid is possible. The process of replacing the oil begins with the drain of the old working composition, after which it is filled new composition (it can be washing or working fluid new Mark.). As soon as the work is made, the engine starts for 10 minutes, after which the oil merges and, in its place, the new lubricant is poured.
To replace the engine oil by car Ford Focus 2, do this:
- Submold an empty container approximately under the hole for draining the working fluid.
- Unscrew using the key to the "thirteen" plug. At this moment, be careful not to burn hot oil.
- Wait until the oil is completely out of the engine, and then return the plug into place and tighten it with the key.
- Remove oil filter. If you cannot twist the part from hand, use a special puller, a screwdriver or belt. When unscrewing the filter, remember that the oil can also flow from it, so substitute the container, under the interface with the engine.
- Lubricate the sealing gum on the filter and pour oil into it. Turn the filter by hand until the moment when planting place And the gum will touch each other. After that, tighten it to ¾ turns.
- Ensure that the oil filter and the bolt for draining oil Ford Focus 2 are well tightened.
- Fill new oil into the engine. Act gradually - you should not pour all the fluid at once, because it is fraught with exceeding the required volume. When replacing the oil, it is better to first pretend to it a little, but after - bring the level to normal.
- Tighten the neck cover for oil pouring and boot the motor.
pay attention to signal lampinstalled on the Ford Focus panel 2. If everything is normal, it will light up and go out in 2-3 seconds. Now muffle the motor and wait until the oil falls into the pallet. After that, check the level of fluid level on the PCU. The edge of the oil should be between two marks (bottom and top), but closer to the inscription MAX.
Video: Replacing Oil on Ford Focus 2, Engine 1.8
The popular Ford Focus 2 car, like other modern foreign cars, requires timely departure, according to the regulation of the manufacturer. But for many years, the owners and service professionals have learned the design of the car. This showed a lot of information on various Internet forums so that the Ford Focus 2 owners can serve the car. But no matter how true information about independent repairs Ford Focus, people still have any questions - for example, even with such elementary procedures as the engine can be replaced. This task requires practical experience and theoretical knowledge, as well as the choice of engine oil itself. In this article, consider how much it is necessary to pour oils, which types and types choose, and also focus on best manufacturers lubricants.
This section consists of manufacturer's recommendations, as well as subjective opinions of experienced motorists, including owners of Ford. FOCUS 2. Ford recommends replacing the oil through 60-70 thousand kilometers, although this regulation is not suitable for Russia with its unpredictable climate. If we take into account the harsh operating conditions, in this case the replacement regulations will have to shorten up to 10 thousand kilometers. This is the most optimal regulation in which the oil does not have time to lose its beneficial properties, and this will be favorable on the reliability of the engine. Thus, it will be possible to prevent premature wear of DVS parts.
View of oil
- Synthetic - one of the most modern motor oils today. This lubricant has the best useful properties that are considered the best for the term. Accordingly, it favorably affects the replacement regulations. Semi synthetic oil does not freeze and steadily low temperatures. It can be recommended for Ford Focus 2 with a slight mileage
- Mineral oil is the most affordable option in the lubricant market. It is recommended only to big mileagebut with some reservations. For example, such oil due to its thickness prone to freezing at low temperatures
- Semi-synthetic oil - includes 70% mineral Oil and 30% synthetic product. Liquid is poorly resistant to extremely low temperatures. Such a product can be recommended when a lack of funds for synthetic oil, or as an alternative version of cheap "mineral milk".
Factory Oil
The Ford Focus of the second generation was found from the conveyor with factory oil with semi-synthetic oil Ford Formula F 5W-30. For this fluid ford. Developed licensed standards WSS-M2C913-A and WSS-M2C913-B. This oil was flooded since 2009.
Oil-analogs
Given the wide range of lubricants, today it is not necessary to buy an expensive original Ford Formula F 5W-30. No less high-quality oil-analogue can be preferred - for example, the American Motorcraft Full Synthetic 5W-30 S API SN. This is a synthetic oil with Ford branded tolerances. In addition, Motorcraft oil is almost twice as cheaper than the original.
Among other equally high-quality analogues suitable for Ford Focus 2, you can highlight the Castrol Ej 5W-40 Fully Synthetic, the Castrol Magnatec 5W-30 and Motul 5W-30 913C.
Vissedity characteristics
Any engine oil for Ford Focus 2 must have sAE specifications 5W-30 and 5W-40.
How many oil to fill for the Ford Focus 2 engines
- For 1.4 DURATEC 16V 80 liters. with. - 3.8 liters
- For 1.6 TDCI 90 l. with. - 3.8 liters
- For 1.6 DURATEC 16V 100 liters. with. - 4.1 liters
- For 1.6 DURATEC 1.6 TI-VCR 16V 115 liters. with. - 4.1 liters
- For 1.8 DURATEC HE 16V 125 liters. with. - 4.3 liters
- For 2.0i 16V 130 liters. with. - 4.2 liters
- For 2.0 Duratec He 16V 145 liters. with. - 4.3 liters
- For 2.0 TDCI 136 l. with. - 5.5 liters.
Short description
Engine Ford Duratec Ti-VCT 1.6 115 hp It is used to install for Ford Focus 2 cars (Ford Focus II), Ford Mondeo. 5 (Ford Mondeo. V) and Ford C-Max.
Features. Engine 1.6 DURATEC TI-VCT is the same engine only with a system for changing the phase distribution. Also on the engine installed another intake manifold and other engine firmware. All these improvements raised maximum power from 101 hp Up to 115 hp And the torque grew to 5 n m. The engine belt drive motor and there are no hydrocomathers (valves need periodic adjustment). The resource of the engine in practice about 300-350 thousand km (the manufacturer declares 250 thousand km).
Engine characteristics Ford Duratec Ti-VCT 1.6 (115 hp) Focus 2, Mondeo
| Parameter | Value |
|---|---|
| Configuration | L. |
| Number of cylinders | 4 |
| Volume, L. | 1,596 |
| Cylinder diameter, mm | 79,0 |
| Piston stroke, mm | 81,4 |
| Compression ratio | 11 |
| Number of valves on the cylinder | 4 (2-inlet; 2-edition) |
| Gas distribution mechanism | Dohc. |
| The order of the cylinders | 1-3-4-2 |
| Motor rated power / speed crankshaft | 74.3 kW - (115 hp) / 6000 rpm |
| Maximum torque / at the rotational speed of the crankshaft | 155 N M / 4150 rpm |
| Supply system | Distributed injection with electronic control |
| Recommended minimum octane number Gasoline | 95 |
| Environmental norms | Euro 4. |
| Weight, kg | - |
Design
Four-stroke four-cylinder gasoline with electronic system fuel injection and ignition control, with inline cylinders and pistons rotating one common crankshaft, with the top arrangement of two distributional shafts With the system for changing the phases of gas distribution. Engine has liquid system Cooling a closed type with forced circulation. Lubrication system - combined.
Piston
Pistons Ford 1.6 Duratec Ti-Vct differ from the pistons of a simple 1.6 Duratec, so that they are non-violent. There are pistons for valves.
| Parameter | Value |
|---|---|
| Diameter, mm. | 76,00 |
| Compression height, mm | 28,25 |
Piston fingers are the same as on 1.6 DURATEC. The outer diameter of the finger is 19 mm, and its length is 50 mm.
Service
Replacing Oil Engine Ford 1.6 Duratec Ti-Vct. Procedure for replacing oil on Ford Focus 2 cars, Mondeo 5, C-MAX with 1.6 Duratec Ti-VCT engine is not much different from normal motor 1.6 liters. Replacement produce every 20 thousand km or year (which will come before). How many oil in the engine: with a filter replacement 4.1 liters; Without replacing the filter - 3.75 liters. Oil type: 5W-20, 5W-30. Original oil Ford Formula F 5W30 (if there is a desire to pour out another, then it must comply with the Ford WSS-M2C913-A and FORD WSS-M2C913-B specification). Oil filter for the same as for - 1455760.
Replacing the timing belt Ford 1.6 Duratec Ti-VCT Rollers are produced at least once every 160 thousand km. Some car owners have already changed the range of 60-80 thousand km, the valve can be bandaged during the break.
Every 100 thousand km of mileage must be adjusted by valve gaps.
Spark plugs are better replaced every 60 thousand km of mileage.
Replacement air filter Ford 1.6 Duratec Ti-VCT The regulation is carried out every 60,000 km.
Cooling system Ford 1.6 Duratec Ti-VCT It accommodates more coolant than a simple DURATEC of the same volume. Therefore, when replacing the coolant in the cooling system, you will need 6 liters of fluid. Replace you need once every 2 years.
Rules for the replacement of motor oils for the Ford Focus of the second generation, as a rule, are reviewed towards reducing the mileage. Consequently, the optimal period between the shifts of lubrication in the motor will be 7-8 thousand km . Which oil is better to pour into the Ford focus engine and how much does it make sense to look for official Ford oil, let's figure it right now.
Mileage is more than 150,000 km. Oil consumption is practically no, within the normal range. Leone Castrol.
Everything cars Ford. Focus after 2009 releases from the assembly line with a semi-synthetic, which is called FORD Formula F 5W-30 in the engine. This oil corresponds to the tolerances of FöRD WSS-M2C913-A and FORD WSS-M2C913-B.
Conveyor oil produces French ELF Corporation, while the manufacturer does not recommend changing the lubricant in the engine to the first plan maintenance. This is explained special characteristics semi-synthetic oil promoting high-quality engine running.
Fake FORD Formula F 5W-30
The fake is distinguished by non-clear text and dimensional structure of the capacitance.
D0 2009.
Original oil.
For motors collected until 2009, when replacing the old lubricant on the Förd Formula F 5W-30, there is no need to use any special flushing and other liquids, the replacement technology also does not change and for topping in old engine with Ford Formula E 5W-30 You can use new oil formula F.
Actually quite Optional to use Ford Formula F 5W-30. It is enough that the selected oil responds to Ford Ford Ford WSS-M2C913-A and WSS-M2C913-B, especially since for obvious reasons the Ford does not produce any oils and uses third-party products.
Which oil is better to pour in the Ford Focus Engine 2
If there is no desire to experiment with the semi-synthetic, recommended by Ford, you can safely try to pour the oil of the American manufacturer MotoRCraft Full Synthetic 5W-30 S ARI SN.
This is a high-quality synthetic product that it has Ford tolerances . At the same time, the price of this oil is one and a half times lower than the promoted European brands.
And how much to pour?
Filling oils oil.
For a two-liter engine, the Ford Focus will need at least 4.5 liters.
Analogs
Petro-Canada 5W-30.
From European brands often use Castrol Edge 5W-40 Fully Synthetic, Castrol Magnatec 5W-30, but they are more expensive. There are more budget series - Motul 5W-30 913C. 2.5 thousand for 5 liters are asked for him.
Specifications
Following the specification, you can maximize the engine life.
In short, the main indicators of the use of motor oils for the Ford Focu of the second generation remains:
- factory Specifications Ford WSS-M2S913-A and Ford WSS-M2C913-in that must be designated on the sticker, or simply the recommendation of Ford;
- depending on the climatic conditions You can use oils with viscosity characteristics by SAE 5W-30 and 5W-40 .
Oil filter
Bosch oil filter 0 986 452 044 in context. Made qualitatively.
When replacing the lubricant, an oil filter will be replaced.
For motors of 1.4 and 1.6 liters, the Ford filter will have a catalog number 1714387-1883037, but besides it, you can use analogs from Suzuki with a number in the catalog 16510-61ar0, Bosch filters 0 986 452 019, Bosch 0 986 452 044, FRAM PH3614, and good reputation enjoy German filters MANN W 610/1.
findings
Therefore for any motors Ford. FOCUS Use the oil of any manufacturer's manufacturer with Ford tolerances and the above-mentioned viscous characteristics on SAE. Successful to all choices and a large motor resource!
