Rear LED headlights with their own hands. How to make a unique headlight tuning with your own hands quickly and cheap.

Probably, every car owner would like his car to look as stylish as much as possible, and everyone around him envied him. Such a result can be achieved in different ways - The modern market offers many spectacular paintwork compositions, polyterols, vinyl stickers and other tuning materials. But many, putting in order glass, body, wheel disks, often forget about them, although they are not considered the main element of the car, but when proper approach They will attract the views of other motorists in the stream, as well as passersby. Therefore, along with the tuning of the body, the tinting of the rear lights will not be at all unnecessary if you need to make a slightly exclusive detail.

Tinting headlights and law

Before you decide on such an operation, you need to remember that if you break the standards (that is, darkening the lights incorrectly), then the traffic police will write a penalty for it. The amount of it is almost the same as for tinting, which was not performed by GOST. Therefore, many are afraid to do something with headlights, in order not to violate the law and do not pay extra fines.

Methods of application

Refuse to decorate the car in this way only because of the fines - is not a completely correct solution. You just need to know what is allowed and allowed, and what is forbidden, and then you can safely refine the machine. Toning rear lights not only give the car modern appearanceBut also will protect the glass or plastic headlights from various scratches and stamps. The surface will be as smooth as possible if the application process is performed using a special film.

There are two methods that allow you to prevent the headlights. This is the use of paint and tinting rear lights film. Which of these two ways to choose? Each driver will solve for myself. Both methods of tuning have their advantages and cons, differ in terms of cost, investment and time.

Tinting paint: Features

This method of staining is the most economical. However, it is quite laborious. It is necessary to thoroughly clean the surface, pollute plastic or glass, and only after that you can move directly to staining. The process of darkening the lantern takes a long time. And the results are not always like that as I would like. Such tinting of the rear lights is suitable for those who do not want to invest in the tuning of their cars large sums.

Vinyl film: features

This method will take much less time than the previous option. Also this method is less labor-intensive than in the case of staining. But there is one point with which certain difficulties can be. It is necessary to stick the film so that there are no folds on the surface. Among the advantages of use this method You can select the ability to quickly remove the film at any time. There is a lot of shades. There are all colors (for example, a red tinting of the rear lamps looks great. The shade can be chosen to a specific car.

Tinting paint: how to apply varnish or paint

If it is decided to draw darkening using paint, the first thing is necessary to purchase a special preparation. It is best to choose toning varnishes. They are much more convenient in applying and use. The cost of these paint and varnishes May be quite high. But the result is worth it. For the processing of two lanterns there will be enough just one can. The work associated with the procrarian headlights is recommended to perform in the ventilated light rooms. It is best to do this in the fresh air. It is necessary to choose a clear, but not too sunny day.

Toning rear lights with their own hands using paints or varnishes is carried out in several stages. First of all dismantle the headlights. This will allow lacquer to lie on the surface with the maximum smooth layer. It is necessary to take into account that then the lanterns will need to set back. For this you need to have skills.

Next, the surface of glass or plastic of the lantern is definitely degreased. To do this, you can use traditional alcohol or take advantage of special means. After the process is completed, the headla is allowed to dry. Before spraying the paintwork, the cylinder shake. Next, the paint is applied as thin and smooth layer as much as possible. Then the spotlight gives a little dry. You need to put it in such a place so that the painted surface does not get a small garbage and dust. Next, another (or more) layer of paint is applied - while painting should be painted until the headlights are not exceeding the norms of light light. When the lanterns are completely dried, they should be polished to the state of the mirror. After that, the optics can be bet on the car and enjoy the result.

Tinging film: Instruction

The following tools will be needed for work: a construction hairdryer, a sufficiently acute knife, a solution of alcohol and a regular spatula. First of all, the tinting of the rear lamps provides for a thorough cleaning of the surface. Initially, the headlights are cleaned by removing moisture from them. It is convenient and efficient to do with microfiber tissue. Also, experts recommend using special cleaning preparations. Then the alcohol solution is sprayed on the surface of the film and the headlight. This is done in order to simplify the process of tinting.

In order for the vinyl film to lay exactly and take the shape of the rear lights, it is stretched. This is done independently manually either using a hair dryer. The material must be heated, and then the film will become flexible. It is important not to overload vinyl. Otherwise, wrinkles will appear.

What's next

Now we have the most important stage of work. It is necessary using a spatula to pull the material and paste the film on the headlights. If something comes out of the edges, it is cut with a knife. Reviews It is said that the tinting of the rear lights film should be performed very carefully. You can damage the lantern and hands in the process. This is completed on this process, and you can rejoice in the result.

Toning headlights and fines

As you know, all car owners, in the country they introduced a ban on too strong tinting the auto glass. This is done to increase security, as visibility is reduced, and the driver of the car may not notice the stop signal or turn signal.

At all, rear lights The overview of the road situation does not affect the road situation, however, if the toning is incorrect, then the car owner threatens not only a fine, the amount of which is similar to the fine for tinting glass, but also the difficulty of moving other cars from behind. Driver reviews repeatedly confirm it.

The law allows you to drive a car, the rear lights of which are white. Others are also allowed light devices yellow, red and orange. Toning of the rear lights ("Priora" is no exception) can significantly change the shades of the radiation of the lantern. Therefore, work should be performed very carefully and carefully. Otherwise you have to pay a fine size of 500 rubles. Inspectors often interpret such tuning as a car malfunction. In the worst case you can lose driver's license By 6-12 months according to paragraph 13 of Art. 12.5 Codex on Administrative Offenses.

When operating the black rear lights, an accident can happen, and in this case the driver will be guilty, which goes with toning. Then you have to pay not only a fine, but also repairing the affected car.

There is an option when you can protect yourself from penalties and at the same time ride a beautiful and spectacular car. Car owner reviews say that this requires dimming in a specialized cabin. How much is the toning of the rear lights? The price in large cities of Russia is from one and a half thousand rubles, depending on the car model and the geometry of the headlight itself. This is a relatively small amount. But by paying it, you can protect yourself from traffic police inspectors and protocols. In practice, no one else will not finish anyone, especially if the headlights are toned competently and skillfully. In this case, the brightness of the glow is practically not reduced. If the inspector sees a gross violation, he may ask to eliminate the fault in place. Reviews say that with the film to do it the easiest.

Conclusion

As you can see, this method of tuning with certain skills can be performed independently. If you do everything competently and follow the instructions, it will not be considered a violation.

Optics on any machine is primarily an element of the motion security system. To make your car individual, many drivers will improve the lighting system independently. There is a headlight with your own hands. Each of them does not require highly specialized equipment, expensive materials or special skills.

Main options for modifying optics

Beautiful headlights give the car more spectacular, exclusive and expensive view

There are several inexpensive and simple options for modifying heads:

cilia;
color film;
toning;
"Angel eyes";
lED ribbons.

Cilia

Without essential financial investments, it is possible with the help of special linings on optics - cilia. Visually, they seem to continue the hood, as they overlap the top of the headlights. Due to this, the car receives a more dynamic and aggressive look. At the same time, the lining can have any form - it all depends on the preferences of the owner of the machine.

Cilia is sold in almost every store details, therefore, a tuning of headlights can make every car enthusiast. You need to select the desired plastic profile and cut the appropriate component. Before installing, the obtained parts are painted in suitable color. Then using double-sided adhesion, the lining are installed on optics.

There is a way to make more spectacular cilia. To do this, you will need:

fiberglass;
epoxy adhesive;
sandpaper;
primer;
malyary and bilateral scotch;
paint;
fiberglass scissors;
set of keys for removing and installing optics;
marker.

The first thing you need to do is to remove the headlights. Then, with the help of the scotch, overlap the glazing zone. On top there are strips of fiberglass of the desired width, which are impregnated with "epoxy". When they dry, another tape and glue are applied. It must be repeated until you get four uniform layers.

Then on top is pasted with greasy tape. It creates pressure to make the workpiece take shape, like the glazing profile. Depending on the manufacturer, epoxy glue dries from eight hours to days. With the help of the marker, markup is applied to the cut, which you need to walk with scissors. After that, the workpiece is processed by sandpaper, primer and paint applied. After drying, the finished products are glued to the headlights on double-sided tape.

This method allows you to create different design of cilia. Many recommend even to make several options, and then just choose the most attractive.

This method has its advantages:

ease of creation;
overlaps the gap between the hood and optics;
stylish tuning view;
there is no problems when replacing.

Color film

This method allows headlights quickly and cheap. To do this, you need to have:

color toning film;
detergent and napkin;
soap solution;
sharp knife;
rubber rocket;
set of keys for mounting headlights;
marker.

In order to facilitate the gluing procedure, the optics must be previously removed. Glass is wetting detergent And dry wipes with a napkin.

After that, to the spotlight, you must attach a toning film and place it with a marker. Cut the necessary part. Then the protective layer is removed on the film and is wetted by soap solution, as well as the optics itself. Then the surfaces are connected.

Heated the film with a hairdryer, you need to slowly smooth it with a rubber rhael, which allows you to remove air bubbles. The optics are then installed in the original position.

Toning

Make tuning headlights with your own hands, like many others, is not difficult. Need to highlight a few hours of free time and purchase necessary materials. In particular, to give optics a new shade of the glow with the help of a compose, you need:

professional paint balloon, which is intended for headlights;
paper tape;
degreaser;
napkins for polishing;
a set of keys.

Headlights are removed, cleaned from dirt and dust. Areas that will not be covered with toning, closed with scotch. The desired segments are degreasing.

Before applying the paint, the balloon for five minutes is better to put in hot water - it will make the lacquer more plastic. Spraying is needed at a distance of 30 centimeters from the headlight surface. After creating the first layer, it is necessary to wait some time specified in the instruction so that everything is dried. Then the action is repeated.

IMPORTANT! In case of acceleration, drows may appear. Then everything must be removed by a solvent that does not hurt the optics, and repeat the whole process. The glitter of the surface will give a special napkin for polishing.

"Angel Eyes"

At first glance, the LED tuning headlights "Angelic Eyes" is something impossible. But if you consider detail - the whole process is simple and short. To do this, it is necessary to prepare the following materials and tools:

lEDs of the desired color - usually it is blue or white;
two resistors for 220 ohms;
wire;
pliers;
soldering iron;
feet;
sandpaper;
transparent plastic tubes;
stationery knife;
insulating tape;
construction hairdryer;
battery for nine volts;
stencil, around which can bent plastic.

The transparent tube heats up and bends around the stencil. To do this, it is better to use pliers. With the help of a knife is cut unnecessary, the edges are stitched. It turns out a ring that exactly corresponds to the size of glazing. After cooling, the rings appears a small gap from two to five centimeters. Over all circumference at a distance of half a hundred meters from each other, with the help of a knife, depresses are made in several millimeters and "brought to mind" with the help of the appliance.

After that, the wire is attacked by the LED for one leg, and the wire and the resistor is on the other. After that you need to connect the battery to check the performance. All contacts are wrapped with a tape. By the same principle, the second LED is made.

After that, both are connected to each other. The resulting light design is mounted into the gap of the plastic circle so that the diodes are accommodated at different parts of the tube. Next, the system is again checked for performance. If everything functions normally - the system is mounted in the outlined places.

LED ribbons

To supplement the image of the "Angel Eye", often produced LED tuning headlights with a special tape. To do this, you will need not much:

lED Strip Light;
wires for connecting;
soldering iron;
transparent glue;
degreaser.

First you need to measure the desired length of the light strip into each headlight. After that, the connectors are soldered to connectivity.

Before gluing, it is necessary to degrease the surface. Ribbons are installed directly on transparent glass. After that, the headlights turn into pronounced "eyes", which gives the car an aggressive character.

Any optics tuning system will immediately highlight the owner. vehicle Among the rest. In addition, after such an improvement, the car instantly starts "more expensive" look. At the same time, it is only a few hours of free time to create the desired effect, as well as purchase the necessary components.

Decorating the back headlights

Often, a lot of attention is paid to the front headlights, and about the rear usually forget, and in vain, they can also be quick enough and just decorate by setting them the LED ribbon.

It will take a tape to 120 light elements, dismantle the headlight and remove the glass to do this, you need to remove the sealant (by heating and using the knife). Glass S. inner We stick with the help of painting scotch.

The remaining surface is important to isolate from drops of paint, and internal part stain silver color. When the paint finally dries, we remove the scotch and the fare will remain a relief pattern. We glue the necessary size of the LED tape with the help of a superclay or double-sided tape and connect the wires.

Staining was performed to ensure a uniform glow of dimensions. During such tuning, turn off the lighting lamp of the headlight is not necessary, it is enough to plot the contacts of the dimensions.

How to highlight the car from the inside

Internal light tuning auto with your own hands can be carried out in two ways: a ribbon of LEDs and neon lamps.

Neon Salon

It will take:

Kapron clamps.
Aluminum corner.
Neon lamps.
Saws.

It is more correct to start tuning from installing neon at the bottom of the cabin.

Most often, neon lamps are produced with a cigarette lighter connector, it must be cut off, after which it is cleaned ends. Then we saw the angle corresponding to the dimensions of the lamp, and screw it under the torpedo in the cabin. Kapron clamps fix the lamp on the corner. The same is done in the other places of the cabin, except rear seats, there is a corner attached up the edge to protect the lamp from damage.

The ends of the wires stretch under the rugs to the torpedo from the driver's seat and in the connection places are insulating. Then we connect them to the door sensor, the light switch in the cabin and the battery. It is also important not to forget to connect one of the wires to the sensor throttle valveSo that in the future he notified about the existing lighting during the flashing of the ECU, it is necessary that neon lamps do not overcome.

The result will be a triggering backlight during the opening of the doors, which will affect its unusualness not only you, but also passing by the transitions.

LED salon

Connecting the backlight using LEDs is similar to neon, the only one needs to position the ribbon correctly (it is possible to cut off individual pieces), and then clean the tips and solder each other, sleeves are put on the scenes for security purposes and warm up using a hair dryer.

Luminous bottom

Immediately warn that the tuning of light for the bottom of the car is illegal, since changes are not provided for by manufacturers and machine designs. But this does not stop many motorists, so it is necessary to produce such upgrades or not to solve you.

Previously, the "lower" tuning was produced using neon, but it was quite disadvantageous and tuners switched to LED backlight, which is much easier in the installation plan and consumes much less electricity.

You will need:

Waterproof LED tape.
Soldering iron and everything you need for soldering.

We measure the size of the bottom and cut the ribbon of the desired size. Well, if you have 4 pieces. After that, contacts are soldered to each piece. Then we install them on the bottom of the car with the help of clamps, so it will hold much stronger than if you glue it to glue.

Swipe through the holes, connect to dimensions or make a separate power button.

The bottom backlight procedure as well as the rest does not require special knowledge, even a novice car enthusiast will cope with it. The main thing, with such tuning not to get to the eyes of the DPS employee.

In conclusion, we note that tuning light refers to inexpensive and spectacular ways to distinguish itself. It can be realized on his car in a short time, so do not be afraid to experiment, and the result will be at the height.

The model of the domestic automaker VAZ 2114 is literally created for tuning and refinement. Whole line external changes Allows you to transform the car, to play with new paints. Some go on and besides external tuningThe methods of improving technical specifications are used.

Today we will talk about tuning optics, or rather rear headlights.

LEDs as impetus to development

With the advent of the LED, the development of tuning rushed sharply forward. All new and unique solutions began to appear, no other light bulbs make it possible to achieve such a visual effect as diodes.

With the help of LEDs, you can decorate the interior, doors, optics. If ahead is now fashionable to establish the so-called angelic eyes, then special elements based on diodes are most often mounted for rear headlamps.

LEDs possess not only decorative, but also practical properties. Due to them, safety increases, since the level of the glow is higher. But the most important thing is similar to the optics refinement is allowed by the legislation of our country and not only.

Tuning species

Tuning optics is not a difficult thing, even if you are relatively new to this issue. Here the main thing is to start to decide which option to finalize the rear headlights you want to use for your VAZ 2114.

Today, several major ideas are especially popular.

Type Tuning	Features
LED linings	Popular and financially available option. There are plenty of finished linings on the market, but you can make it yourself. To create a lining you use fiberglass, LEDs and epoxy glue
Rings from diodes	This option is refined full replacement Rear optics on diode rings. For their manufacture, you will need a serious experience in working with electronic devices.
Lamps of powerful glow	This type of refinement simultaneously provides for the use of tinting film for headlights. Due to the tone, the bright light will be better focused. But powerful lamps have minuses - increase fuel consumption, load the generator and overheat wiring. Since the engine power in the VAZ 2114 is not high, this option is not completely reasonable
Separate LED elements	The most original version of refinement, since it allows you to maximize your own fantasy. But you have to spend time and effort to create a drawing from diodes and their installation.

From the point of view of money saving, the purchase of individual LEDs will be more profitable than the purchase of finished products. But in this case, you must be sure that you can get devices high Quality. Otherwise, it is better not to risk and spend more money.

Manufacture

Now we will tell you how to create the above types of LED devices specified above, designed to install in the rear lights of the fourteenth model from AvtoVAZ.

Pads

Let's start with the creation of diode linings. To work, you will need the following set of tools and materials:

Fiberglass;
A set of LEDs;
Stationery sharp knife;
Paintwork;
Epoxy adhesive;
Malyary Scotch.

We offer to familiarize yourself with the instruction that will help to figure out the nuances independent manufacture and installing finished linings. For fastening elements, you can use tape or similar materials.

Cover the back optics using a painting tape. Then apply fiberglass on the tape.
Perform the impregnation of fiberglass using epoxy glue, which will allow you to install the lining. The glue should be applied in two or three layers, but only layers should be thin.
Drying is usually about 12 hours. But still familiarize yourself with the instructions for the epoxy glue that you purchased and use.
Now remove the workpiece and mark up the contours of the future decor. To do this, use the scotch or marker.
With scissors cut the resulting profile.
Cutting a form, start to put off.
When the surface serves, process it with fine-grained emery paper.
Now apply a layer of primer, and then layer of paint.
When the paint is completely dry, you can apply a protective varnish.
Install the pads on the rear lights, after which the tuning can be considered completed.

Such linings are decorated with both rear lights and turn signals, fog ahead. Consider the option with the installation of diodes into the wheels or inside the cabin.

Installing diodes inside headlights

The lining are mounted directly over the rear optics, and the following option provides them with an insert inside headlights.

Before installing, prepare LEDs and fees. If you do everything right, you can easily connect new LEDs to the wiring of your car;
Make a stabilization scheme. Here are stabilizers under the catalog number 7812. This will allow when the dimensions are turned on the diodes shine more weakly, and when the stop signals are turned on to maximize its power.

To work, you will also use:

LEDs with resistors;
Fasteners for diodes;
Adhesive film;
Silicone sealant;
Epoxy glue, etc.

To determine the number of necessary diodes, learn your hind lights, take into account the rotor relays. You must certainly buy diodes with a margin, because over time they are able to abandon, and find the same in a year or two may be a problem.

For diffusers, choose white diodes, and for turn signals - orange, brakes - red, and reverse - Just transparent.

So, proceed.

Remove the flashlight, then cut it into two components. To do this, a high-quality tool for burning is useful. Try to get thin, as much as possible seam.
Remove reflectors and reflectors.
Fully disassemble the back optics. Make marker for the position of diodes on the outer surface.
Internal space are covered with mugs of self-adhesive film. Their diameter should be 15 millimeters.
Overall lights and stop headlights Treat silver color paint. After its complete drying, remove the film.
Reflectors are mounted on a thin layer of epoxy. It will not be superfluous to process all the joints with the help of sealant.
Boards with LEDs are mounted on the wiring and placed inside the headlight housing.
Now turn the stabilization scheme. It will adjust the connections of diodes.
Collect and connect rotary blocks with rear optics. Modules seated on epoxy glue. If the inspection of the rear headlights showed that everything works fine, glue the unit and complete tuning.

A very common version of the tuning of the rear optics, in which an incredible visual effect is achieved. In many respects, the result depends on the applied effort, developed design and quality of the materials used. All in your hands.

To create elements, ribbons or LED finished rings are used. The body makes from a dashboard of different sizes that are not difficult to find in the markets of automotive spare parts.

Collect paint at your discretion. Today is popular to use chrome or silver.

Diode rings should be inside the cylinders. For their manufacture, simple tin cans are suitable - from coffee, conservation, etc.
Cut them with neatly sharp knife or scissors for metal to get a mini well as a result. Make two such elements. One will be inner, and the second is external.
Alternatively, the outer well is made of tin, and internal - from plastic, which is then painted in the desired color.
Inside the inner well, the Soviet cataphots will be mounted, which will ensure the glow in the standard diagram. Namely, turn signals - orange color, rear - white, fog lights - red.
A decent amount of unnecessary elements can be left from the big catathot, which will perfectly complement the inner space of the module. The remaining place fill in other LED rings at your discretion.
Now you need to mount reflectors and rings from LEDs. For their reliable fixation, refer to the ribs. Actually use epoxylin.
Additional highlighting is often installed on the plexiglass and fix it with epoxy glue.

Options for the refinement of the rear optics on the fourteenth model, a great set. You just have to choose the type of tuning, which likes more than others and meets the possibilities for self-making.

If experience is not enough, but I still really want to improve the appearance of your VAZ 2114, we advise you to contact the appropriate Tuning Atelier. Today there are many of them, because there should be no problems with finding the performer.

In most cases, the design and design of the rear lights is completely satisfied with motorists. At the same time, there are no cases when optics are subjected to a certain refinement. Most often, autotuning lovers, as well as owners of domestic models, whose lights are not distinguished by uniqueness and sufficient brightness.

Rear head tuning

Today there are many options for improving the rear optics. The simplest and affordable: brilliant stickers, powerful light bulbs with toned film, LEDs and lining. Consider in more detail these vehicles tuning car.

Stickers It is quite difficult to call the stylish or unique way to give rear lamps of originality. Most likely, it is a children's fun, which no one perceives seriously.
Powerful light bulbs As a rule, installed with tinted film, which darkens the diffuser. Such upgrades of optics is completely ineffective and fraught bad consequences. More powerful lamps create additional load For the generator and lead to overheating. The consequence of such modernization may be the option when the rear headlights do not completely burn.
LEDs - The most original way to give a car stylish and presentable view. It allows you to implement various unique design solutions with minimal costs at maximum efficiency.
Pads - The most common and affordable version of the tuning for any car model. Today you can buy different kinds ready-made sets, but standard typical sets do not differ in particular originality and do not always look spectacically on the car. More unique, there may be overlays on the rear headlights made with their own hands based on fiberglass and epoxy glue.

Installing LEDs with your own hands

The advantages of tuning rear optics with LEDs are:

Reducing energy consumption.
Original and stylish look.
The brightness of LED optics is several times more compared to conventional light bulbs, which makes it possible to abandon the use of reflectors.
The ability to group LEDs in any order and quantity that is limited to only your fantasy and size of the free space available in the back of the car.

Preparation for tuning

To make LED rear headlights with their own hands, it is necessary to purchase a certain number of diodes. For regular scattens optimal option may be elements white color 12-16 volts with a capacity. If you plan to establish transparent scattens, you should buy red LEDs for overall and brake lamps. For turn signals, the elements of an orange shade will be needed, and for the optics of the reverse - white diodes.

LEDs are recommended to buy with a margin in case when the failure of a certain number of elements during operation, it was possible to immediately replace them, and not run in search of the desired store model.

The number of LEDs must be chosen based on specific features Lanterns with such a calculation so that in each section of the optics there was enough space. Also should take into account such a moment as the blinking relays of turns. In the design of the car, each relay is selected taking into account a certain load. Therefore, it is necessary to provide such a number of LEDs that will correspond to this parameter. Otherwise, the frequency of flashing optics will differ from the standard scheme.

In addition to the LEDs, it is necessary to stock up with a thin plastic from a foil getinaks or dielectric. It will be needed to improve the fastening of diodes.

If you use Ghetinaks, you have to reinstate the current tracks by the number of items installed. Although this method is time-consuming, however, such a design will be more compact and durable. In the case of a dielectric, the power is implemented easier, with a thin wire. In this case, it is necessary to take care of the reliable mounting of the wiring and other elements to eliminate their damage with strong vibration.

All LEDs are sensitive to vibration and shaking, so you should take care of the reliability of their attachment. Elements must be inserted with tension. In this case, the connection of wires with diodes should be made only by the soldering method.

Power connection is performed parallel in the way Through resistors that are designed to limit currents passing through diodes. In order not to select resistors yourself, it is better to immediately buy them complete with LEDs.

Video - how to make a tuning of the rear headlight yourself

When the nutrition arrange, it is follows particular attention to the fastening of resistors. They must be reliably fixed in this position so that they do not touch the wires.
All compounds must be carefully insulated with thin heat shrink tubes or plastic cambricks. In places where the wire comes into contact with the sharp edges of the optics housing, also additionally install protection from a dense cambrick.
Installation of LEDs on the rear headlights
Installing LEDs on the rear lights is performed in such a sequence:
We dismantle the lamp and cut it carefully. To do this, it is best to use the burning device. In this case, you will get a thin and even seam.
Remove reflectors of rotary lamps and pull out reflectors.
We disassemble the rear headlights.
On the outer surfaces are placing the optimal position of the reflectors.
From the self-adhesive film, we cut 15-millimeter circles and glue them inside.
The inner surface of the stop headlights and dimensions stain with silver paint. After drying, the mug can be removed.
Using epoxy glue by mounting reflectors. Additionally, all joints are missing with silicone sealant.
Pre-soldered on the LED cards are installed in the housing and connect the wiring.
To the LEDs in the Stop mode burned on full powerAnd in the "Dimensions" mode is less bright, it is necessary to pre-collect and discharge the stabilization scheme. As a basis, you can take the voltage stabilizers "7812".
We collect rotary blocks and install with the rest of the details in the headlights. Modules secure with epoxy glue.
Check the work of optics. If everything works, you can proceed to the fill of the blocks of lights.

Lining on the rear lights
Stylish and rear headlamps can be independently made of fiberglass. To do this, you will need fiberglass, epoxy glue, spittle, primer, paint, varnish and greasy tape.
Cover the lanterns with painting scotch. Then we apply fiberglass and impregnate it with epoxy glue. Well smoothed irregularities and wait until the layer dries. Specialists recommend fiberglass with epoxy to apply thin layers into several techniques.
After complete drying (10-12 hours), we remove the workpiece and the marker draw the contours of the future part. After that, cuts the desired profile.
Carved forms with spit, and after drying with sandpaper with emery paper. Then the overlays are ground and paint. At the final stage, we cover the details of the lacquer. Painted overlays on the taillights with the help of bilateral scotch.

The appearance of modern LED elements led to the creation of a new turn in car tuning. Motorists began to decorate the interior of the car, doors and, of course, optics. If the front optics are decorated with "angel eyes", then the rear lights owners of VAZ 2114 and other cars prefer to put LED elements. Rear lights On VAZ 2114 it is easy to tuning, but almost all of them are associated with the installation of diodes.

Interesting: In addition to the decorative value, the LED backlight is also present and practical benefits: LEDs increase safety, so their glow is brighter than that of incandescent lamps; Riding becomes more comfortable in all weather conditions. At the same time, such tuning is permitted by law in the CIS countries.

Tuning Options Rear Lights

LED lining, diode rings on lights, separate LEDs and powerful light bulbs in the darning film - tinting are very popular. Attention deserves each option to decorate optics:

Making overlays

For the manufacture of linings, you will need the following tools and materials:

The instruction is suitable for homemade decorative decoration or purchased. Muffd up diode linings with a scotch or its alternative:

Rear lights need to be covered with painting scotch. After that, you need to apply fiberglass on the tape.
LED lining will be installed in it, then the fiberglass must be impregnated with epoxy glue. It follows 2-3 thin layers. All irregularities need to be removed, and then wait for a complete drying, which is in ordinary garage conditions lasts 12 hours.
When the glue is dry, you can remove the workpiece, and then schedule the contours of the future ornament with a scotch or marker. After that, the developed profile is cut with scissors. When two forms are cut, you can move to putty. The dried surface must be pulled out fine-grained sandpaper. After the soil is applied, and then the main layer of paint.
After 100 percent drying, a protective varnish is applied. Diode overlays are installed on the rear lights. Tuning completed.

Tip: lED lamps You can decorate not only the rear lights. VAZ owners often put LED tapes as turn signals and fog lights on front optics. Another interesting option is to decorate wheel disks and dashboard.

Installing LEDs in the rear lights

If the LED linings are installed on top of optics, then the diodes need to be inserted into the headlights - it will take the skill of working with electronics and a soldering iron. Before starting the installation, the LEDs should be prepared along with the board, it all depends on the possibilities and desires of the motorist - in the future the LEDs should be freely connected to the wiring of the car VAZ 2114. It is also necessary to make a stabilizing circuit. For this, stabilizers are sold, which are sold at the number "7812". It is necessary so that lights in the overall mode ensure a weaker glow, and 100% power was given in the stop position.

For those drivers who value the creative, you can advise to make LED arrows on the taillights, which will be used in the future to indicate the turn. It looks stylish and original. Motorist will need to collect several boards that will depict the arrow.

Such tuning with your own hands requires a large number of materials. This is a set of LEDs along with resistors, fastening for diodes, adhesive film, sealant (preferably it is silicone), epoxy glue. Surrounding may find the question "How many tuning requires LEDs?". Here you need to independently explore your taillights, while taking into account the turning relays. You need to buy LEDs with a reserve, as they can overdo it with time, and an exact copy may not be. The role of diffusers, according to motorists, the white LEDs are better suited, the turn signals decorate orange diode elements, "brakes" - red, and reverse - transparent.