Modern cars are equipped with a wide variety of signaling devices and illumination. They can be located both outside the car and inside its cabin. All these devices are combined into a single vehicle lighting system. An important role in the safe operation of the machine is played by taillights.
Rear lights of the car
Many car owners today carry out their own tuning of the rear lights, converting them into LED lamps. To carry out such tuning efficiently and quickly, you need to know not only the functional structure of the lights, but also the phased process of the headlights alteration. Our today's article will help you deal with all the nuances of this work.
Functional purpose of devices
To make a homemade LED car light, you must first of all know the purpose of this device. Otherwise, the new tuning may not meet the functional responsibilities of the lighting fixture.
Rear lights car are part of the vehicle lighting system. At the same time, they perform a number of functions, which should include the following points:
- when driving in reverse, such headlights provide high-quality illumination of the roadway;
- inform other road users driving behind the car about its presence on the roadway in bad weather conditions, as well as at night;
- informing behind the driving motorists about the intention of the driver to turn left or right;
- transmission of information to other drivers about an accident or stopping a vehicle.
Car at night on the road
To perform these functions, the taillights will always be painted in white color... In addition, they have a much larger beam of light than brake lights. This device combines such lighting devices as:
- stop signal;
- turn signals;
- lights-dimensions;
- signal reverse.
As you can see, the taillights are a cumulative lighting setup. It is placed on any machine symmetrically and in pairs. Very often, such a headlamp is a single unit, which includes all of the lights and signals listed above. Somewhat less often in the vehicle configuration, there are lights consisting of two blocks. They are installed in pairs on each side. As a result, not two, but four lighting fixtures will be installed behind the car.
Many modern vehicles have a diode tail light, namely its turn signals. But not all domestic cars boast such modern taillights. Therefore, many car owners prefer to do this tuning with their own hands.
Modern lighting devices
Previously, the taillights of cars were rather bulky devices, but modern lighting systems are characterized by miniature and beautiful design.
Rear lights design
Moreover, they are capable of performing several functions at once, which we talked about above. Modern manufacturers are trying to create the most unusual headlight design, making it a unique feature of the vehicle.
Note! LED taillights are relatively new. Therefore, many cars at the moment have an outdated headlight structure.
But to make the rear lights of the car modern and beautiful without led headlights, you can do it yourself. For this, you can use modern LED light sources. For tuning, you can use both LED strips and separate diodes. In this situation, a diode will be used as the main lighting element.
Why choose led
The diode as the main light source in the vehicle lighting system has become very popular for the following reasons:
- excellent luminous flux, which has favorable technical characteristics;
- the diode operates at a low voltage, which makes it possible to power such a backlight from car battery without any problems;
- long service life, which when correct installation lighting device is about 10 years;
- the diode practically does not heat up during its operation;
- light source resistance to mechanical stress and vibrations. Moreover, the resistance to vibration for the car is very important, since during its movement along the roadway, many parts of the body are subjected to minor vibration effects.
At the same time, the most important advantage of a diode light source is its color variety. As a result, the illumination of the taillights can be made very diverse, which will give your car a greater uniqueness and originality. Moreover, such a backlight can be easily installed with your own hands, even on a domestic car.
Unlike older lighting installations, LED lights do not dazzle the eyes, but create a soft glow. Due to its excellent characteristics, the light that the diode creates will be visible for several kilometers.
The availability of LED products makes this type of tuning not only the most profitable, but also in an accessible way effective and practical car lighting. Done right, you get beautiful taillights that reflect your personality.
Reasons for tuning headlights
You can make rear diode lights on your car not only to improve appearance vehicle and improve the light performance of the headlights, but also in order to prevent the failure of the lighting device.
It makes sense to carry out such a headlight tuning in the presence of the following situations:
- decrease in the quality of the glow of devices;
- constantly ongoing oxidation process in lighting fixtures;
- burnout of backlight bulbs;
- loss of contact in the device;
- various problems with the lighting fixture.
An excellent solution to all of the above situations would be to install LEDs with your own hands. During the installation of new lighting elements, you can simultaneously fix all existing minor problems that you can fix on your own.
What you need to know about LED headlights
IN modern cars LED lamps are made from an array of diodes that generate light through the so-called electroluminescence effect. The effect of electroluminescence should be understood as the optical-electrical phenomenon of the glow of crystals and gases of phosphorus or other structures when they are exposed to an electric field or current.
Note! This kind of technology allows you to maintain a low power consumption compared to other lighting methods implemented using fluorescent and neon bulbs.
Modern LED headlights
The diode, which is built into the rear lights of the car, allows you to increase the visible distance on the road by two and a half meters. This increase in apparent distance gives the driver extra seconds, which will allow him to better orientate on the road, avoiding dangerous maneuvers and situations that pose a threat to human life and health. As a result, diode tuning will make it possible to achieve greater safety of movement on the roadway at night. In addition, the diode has a lot of positive characteristics, which we talked about above. Thanks to them
The LED home-made light increases the reliability of both the backlight and the vehicle lighting system as a whole.
Thus, LED car lights are an excellent compromise between the distance required to identify the vehicle on the road and the situation of dazzling the driver driving behind. As you can see, the decision to independently tune the rear lights of the car and use a diode for this ( different types LED products) will be a huge plus and will make it safer to find a vehicle on the road!
Things to keep in mind while working
Before proceeding with the manufacture of an LED lamp for a car with your own hands, you need to know the following nuances of this work:
- each diode that will be installed in the headlamp must be assembled in a group in parallel with series resistors (protection and equalizing);
- it is recommended to use only light sources with increased brightness;
High brightness LEDs
- you also need special reflectors, with which you can increase the brightness of the glow of light sources. This is due to the fact that the power of such light sources is not enough to create a luminous flux at the same level as conventional incandescent lamps;
- you need to use colored plastic caps that actively absorb the coherent radiation of the diodes. With these caps, it is possible to match the emission frequency of the light source.
In this regard, we can conclude that creating a homemade high-quality LED lamp for a car is possible, but only with strict adherence to the assembly instructions and knowledge important nuances works.
Step-by-step assembly instructions
You can use various instructions to assemble a diode taillight with your own hands. Consider the simplest and cheapest option for making such a lighting installation with your own hands, based on the use of an LED ring.
For this we need the following materials:
- red diodes with a diameter of 5 mm (64 pieces). You can take medium brightness;
- for stops - 20 LEDs with increased brightness;
- resistance (120, 150 and 270 Ohm);
- 12 V power supply - needed for testing;
- can of matte black paint;
- 4 pieces of plastic. They must be flat;
- 4 voltage stabilizers, which will go in size.
From the tools you will need:
- screwdriver;
- glue gun;
- nippers;
- heat shrinkage;
- soldering iron;
- tester;
- technical hair dryer.
The step-by-step instructions for assembling the flashlight are as follows:
- cut off the glass from the old headlights. To do this, it must be constantly heated with a construction hairdryer;
- then we take out the diffusers and paint the reflectors in black light;
Headlight without diffusers
- then, from a plastic piece, we form a platform for placing LEDs in it and implant LEDs into it;
Note! You can place LEDs on a plastic base in a variety of ways. In this case, a circle was chosen.
Prepared plastic platform
- solder the leads from the standard headlight holders to the LEDs and connect them to check the correct connection of the light sources;
- we solder stabilizers into the electrical circuit;
Soldered electrical circuit elements
- we put on a reflector painted in black light on top of the diodes;
Working LEDs
- put all the components of the lantern in place;
Replacing the LED backlight
- after that, glue the headlight glass back to the sealant. It takes a couple of days for the sealant to harden;
- then we remove the bumper and under it we find the guides with which the headlight is held on it;
- carefully screw the headlight into place, having previously connected all the wires.
The finished result of tuning
The above steps must be repeated for all lights that are located at the rear of the vehicle.
Conclusion
Anyone who has at least minimal knowledge of electronics can modify the rear headlight of a car with their own hands and install LED backlighting into it. Having done all the necessary actions correctly, you can quickly and cheaply make your own vehicle more comfortable to drive, as well as increase your safety while participating in road traffic.
Choosing a lamp for a bathroom mirror, placement options Biofireplaces as part of a room's interior
The advent of modern LED elements has led to the creation of a new round in car tuning... Motorists began to decorate the car interior, doors and, of course, optics. If the front optics are decorated with "angel eyes", then the owners of VAZ 2114 and other cars prefer to install LED elements on the rear lights. The taillights on the VAZ 2114 are easy to tune, but almost all of them are associated with the installation of diodes.
Interesting: in addition to the decorative value, LED backlighting also has practical benefits: LEDs increase safety, as their glow is brighter than that of incandescent lamps; riding becomes more comfortable in all weather conditions. Moreover, such tuning is allowed by law in the CIS countries.
Tuning options for the rear lights
Very popular are LED strips, diode rings for lights, individual LEDs and powerful bulbs in a dimming film - toning. Each option for decorating optics deserves attention:
Manufacturing of overlays
To make do-it-yourself linings, you will need the following tools and materials:
The instruction is suitable for homemade decorative or commercial items. Diode pads are attached with tape or its alternative:
- The taillights should be covered with masking tape. After that, you need to apply fiberglass to the tape.
- LED pads will be installed in it, then the fiberglass needs to be impregnated with epoxy glue. It should be applied in 2-3 thin layers. All irregularities must be removed, and then wait for complete drying, which in normal garage conditions lasts 12 hours.
- When the glue has dried, you can remove the workpiece, and then outline the contours of the future decoration with tape or a marker. After that, the developed profile is cut with scissors. When the two shapes have been cut, you can move on to the putty. The dried surface must be sanded with fine-grained sandpaper. After that, the primer is applied, and then the main layer of paint.
- After 100% drying, a protective varnish is applied. Diode trims are installed on the rear lights. Tuning completed.
Advice: lED lamps you can decorate not only the taillights. VAZ owners often use LED strips as turn signals and fog lights on the front optics. Another interesting option is decoration rims and dashboard.
Installing LEDs in the rear lights
If the LED pads are installed on top of the optics, then the diodes need to be inserted into the headlights - you will need the skill of working with electronics and a soldering iron. Before starting the installation, you should prepare the LEDs along with the board, it all depends on the capabilities and desires of the motorist - in the future, the LEDs should be freely connected to the wiring of the VAZ 2114 car. It is also necessary to make a stabilizing circuit. For this, stabilizers are suitable, which are sold under the number "7812". This is necessary so that the lights in the overall mode provide a weaker glow, and in the "STOP" position they give out 100% power.
For those drivers who appreciate creativity, it is advisable to make LED arrows on the taillights, which will be used in the future to indicate the turn. It looks stylish and original. The motorist will need to collect several boards that will represent the arrow.
Do-it-yourself tuning requires a lot of materials. This is a set of LEDs along with resistors, mounts for diodes, adhesive tape, sealant (preferably silicone), epoxy glue. The question "How much does tuning require LEDs?" Here you need to independently study your taillights, while taking into account the turn relay. You need to buy LEDs with a margin, as they can burn out over time, and there may no longer be an exact copy. For the role of diffusers, according to motorists, white LEDs are better suited, turn signals are decorated with orange diode elements, "brakes" are red, and reverse gear is transparent.
As a rule, the design and design of standard taillights in passenger cars quite satisfied with their owners. However, in some cases these lighting devices require some improvement, for example, increasing the brightness of the lamps or changing the shape and size of individual sections (brake lights, direction indicators or side lights).
This is especially true for "older" cars domestic production, where the taillights initially do not differ in particular expressiveness and brightness, and over time they even require replacement or serious revision.
Tuning options for the rear lights
There are several options for homemade lantern tuning. In the simplest case, the standard lamps are replaced with more powerful ones, and the lamp diffuser is darkened by pasting with a tint film. Of course, such "tuning" flatters the owner's pride, however electrical wiring such a car works with overload, and the lights themselves shine too dimly and are practically invisible in the daytime.
Gluing the shiny stripes over the diffuser along the borders of the lantern sections is intended to make them more elegant. At least, such a harmless modification does not affect the operation of the light signaling in any way and has a right to life.
Tuning taillights with LED installation
A much more competent option for tuning the rear lights is to install modern LEDs in them. The advantages of this refinement are:
- Compared to traditional incandescent bulbs, LEDs consume much less power;
- Minimum response time (lighting up) of LEDs;
- High brightness and large viewing angles make it possible to abandon the use of reflectors in the design of the lantern and, if desired, make its diffuser colorless;
- The compact size of the LEDs allows them to be positioned and grouped in any order, that is, as the owner wants (of course, all this must be done within the technical standards, as well as the available space on the rear panel of the car).
To upgrade the taillights, we need to buy a certain number of LEDs with an operating voltage of 12-16 volts. In the case of using a standard rear light diffuser (with already painted signal sections), the LEDs should be white or as close to it as possible. If it is planned to make a colorless (transparent) diffuser, then we need red LEDs for brake and side lights, orange for turn signals and white for reversing lights.
The number of LEDs for each section is selected based on the available free space in each section. A plate made of a thin and durable dielectric or foil-clad getinax is best suited for attaching the LEDs legs. In the first case, the installation of LEDs is carried out using pieces of thin wire, and when using a getinax, you can etch the required number of current-carrying paths on it to supply power to "+" and "-". Of course, the 2nd option is somewhat more laborious, but this design looks more accurate and is less afraid of vibrations.
In order for all LEDs to shine equally brightly, they are connected in parallel. When buying, it is best to use such LEDs that already come with a resistor (it is needed to limit the current flowing through the diode). Otherwise, this resistor will have to be selected independently. The resistors must be fastened in such a way that they do not touch adjacent wires and do not damage them.
All connections of the supply wires are carefully insulated with a plastic cambric or a thin heat shrink tube. In those places where the wire can be damaged by sharp edges, it is additionally protected with a dense cambric.
Some relays that set the flashing frequency of the turns are very sensitive to the load. That is, at the factory they are calculated to power four lamps with a capacity of about 50W (21 + 21 + 4 + control lamp in the dashboard). In the case of using diodes with a lower power consumption, the flashing frequency of the lamps may change, so this fact should be borne in mind.
- Like any other part, diodes can fail over time. Therefore, it makes sense to buy them with a small margin, so that, if necessary, do not run around the shops in search of diodes with the characteristics you need;
- Diodes also do not like excessive vibration and shaking. In this regard, the diode bodies are inserted into the board body with some interference, and all connections are made by soldering.
It is probably very difficult to imagine how in modern world you can drive and not use reverse gear, since by and large such a situation simply cannot arise. In addition, movement only during the daytime is not always possible, and therefore you must always have additional function good overview and visibility. That is why it is necessary to ensure maximum comfort in movement to the maximum, both in the evening and at night, and during the day, when there is fog in the yard, it is raining or there are other vagaries of the weather that do not in the best manner directly affect the visibility on the road to all road users.
Based on the foregoing, the main function of this kind of lighting devices will be to illuminate the road when driving backward. In addition, it is these devices that will warn all road users that the motorist intends to reverse, thereby performing an informative function. Nevertheless, unfortunately, sometimes the motorist will need to install an additional device. This is directly related to the fact that the device of a standard flashlight will not be able to fully fulfill all the tasks at the required high level.
1. How to properly install LEDs in the rear lights.
It is important to note that this kind of operation is quite easy, although you need to be very careful when performing all the necessary procedures indicated below. First, you need to dismantle the rear lights with a utility knife and a candle. After that, you will need to remove the glass from the headlight. It is important to note that this will require a high level of care to avoid damaging the plastic or glass. After that, it is necessary to completely remove everything from the headlight itself, and pour the mounting foam inside, which in the future will serve as the basis for attaching the LED strip.
After the polyurethane foam has completely dried, the motorist will need to endow it with the desired shape.In order to provide the desired level of rigidity, the surface of the foam must be reinforced with a pad, which is made of fiberglass. The fabric itself will need to be impregnated with epoxy resin, after which it will be necessary to wait for a certain period of time until it dries.
Then all the light elements must be soldered together, connected, after which it will be necessary to check the operation of the entire established structure. After the headlight glass is applied, the motorist will see the remaining particles of foam, which best case can be disguised. You can also paint it, but it is important to note that you will first need to cover all the LEDs with squares. In addition, it is important to remember that all headlights must be correctly connected to the entire car system and networks.
Power will be supplied to all dimensions, the voltage will be 6 volts, while the brake light devices will be 12 volts. Such a headlamp is quite spectacular and beautiful. However, a certain problem arises, since the brightness of such headlights in the daytime is quite low. To solve the problem, you should install a higher power LED strip. Sometimes, due to the installation of LEDs, an error may occur in the readings of the corresponding device. In order to prevent this, it is necessary to install the "trick".
Now it is necessary to dwell in sufficient detail on the procedure for installing the diode tape or LEDs directly into the reflector. First you need to dismantle the reflector and taillights. The headlight itself will need to be disassembled. In order to glue flexible plastic, you need to use a heat gun or high-quality glue. If diodes are to be used, then they must be soldered together. The structure itself needs to be connected before direct painting, and also to check its performance. This is directly related to the fact that the defective diodes will not light at all, or they will go out a few minutes after switching on. It is important to immediately note that the device of one reflector will require about 5 meters of LED strip.
Nevertheless, the task can be somewhat simplified, since the reversing device can be installed halogen lampswhich will replace the standard lamps. Such devices will have great power, sometimes even doubled. The bulb itself is disassembled, and all the insides are carefully removed with tweezers. Further, the halogen holder-base is inserted directly into the device and the wire is soldered. In order to securely fix the cartridge from the "halogen" itself, it is necessary to fill its metal base with silicone sealant.
Using the simplest syringe without a needle, all the gaps between the ceramic cartridge and the metal base should be evenly filled with sealant. It is important with all this not to forget the fact that halogen type lamps will heat up much more than conventional incandescent lamps. Due to this nature, it is necessary to install a ceramic cartridge device instead of conventional soldering. All the characteristics of the silicone sealant will be maintained when heated to a sufficient temperature.
2. What is needed to install LEDs in the taillights.
All lights that have LEDs are efficient enough, visually stylish and beautiful. In order to install this kind of light elements in reflectors, you will need to drill holes in which 120 LEDs will be installed. All rows of holes must be straight. Among other things, the on-board power supply of the car does not provide for the operation of diodes, in connection with which it will be necessary to purchase 120 suitable resistors. It is necessary to install diodes directly into plastic in accordance with certain instructions... The plane of the plastic itself will be heated by a stream of air, into which the LED will be pressed. After direct cooling of the plastic, the diode will be sufficiently fixed.
You can also use LEDs with a diameter of five millimeters. In this case, it will be necessary to change the taillights, which will occur due to the expansion of the area of \u200b\u200bdimensions and brake lights. The board itself must be clamped and fixed by the internal shape of the headlight. When a special lED Strip Light, installation and installation should be an order of magnitude faster, since there will be no need to install each element separately.
3. Pros and cons of LEDs in the taillights.
The biggest light problem for motorists will be the constant lack of lighting. It is because of this that the question of supplementing or replacing the already built-in and existing standard lamps will arise. This replacement focuses on LED lights. In addition, it is important to note that all LED lights will save a lot of money and time for a motorist to choose and purchase batteries that will drain 80% less than when using traditional and conservative light sources directly.
Based on these considerations, many motorists only dream of replacing standard lamps with expensive LED devices. That is why LEDs are becoming more and more popular in the modern automotive community.
The biggest plus in using LEDs is that they have a sufficiently high coefficient of light output, which will make them an order of magnitude brighter than an ordinary light bulb. It is important to note that this kind of improvement will occur at the same current consumption. It should be noted that not every motorist considers it convenient to push his car in the morning, because of the unplugged music in the car, dimensions and as a result of the "death" of the battery. The most positive thing about led lights that they can be done without any effort by any motorist and novice who wishes to improve their vehicle in driving backwards.
Thus, LEDs in the taillights are the best way out of a situation when standard lamps exhaust themselves with a weak and unpleasant light. The use of LEDs will increase the brightness of the glowing rear parts, since they have a completely different design and principle of operation, and therefore exceed by an order of magnitude all their standard factory (and not only) counterparts.
Subscribe to our feeds in
Probably, every car owner would like his car to look as stylish as possible, and everyone around him envied him. This result can be achieved with a mass different ways - the modern market offers many spectacular paints and varnishes, polishes, vinyl stickers and other materials for tuning. But many, having put in order the glass, the body, wheel disks, often forget about They, although they are not considered the main element of the car, but when the right approach will attract the glances of other motorists in the stream, as well as passers-by. Therefore, along with tuning the body, tinting the taillights will not be superfluous at all if you need to give the exterior a few exclusive details.
Headlight tinting and the law
Before deciding on such an operation, you need to remember that if you violate the standards (that is, darken the lights incorrectly), then the traffic police will issue a fine for this. Its amount is almost the same as for tinting, which is not done according to GOST. Therefore, many are afraid to do something with the headlights, so as not to break the law and not pay extra fines.
Application methods
Refusing to decorate a car in this way just because of fines is not entirely the right decision. You just need to find out what is allowed and allowed, and what is prohibited, and then you can safely modify the car. Tinting the rear lights will not only give the car a modern look, but also protect the glass or plastic of the headlight from various scratches and dims. The surface will become as even as possible if the application process is carried out using a special film. 
There are two methods to darken the headlights. This is the use of paint and tinting the taillights with foil. Which of these two ways should you choose? Each driver will decide for himself. Both tuning methods have their pros and cons, differ in cost, labor input and time.
Paint tinting: features
This method of painting headlights is as economical as possible. However, it is quite time consuming. It is necessary to thoroughly clean the surface, sand the plastic or glass, and only after that you can proceed directly to painting. The darkening process takes a long time. And the results are not always the way we would like. Such tinted taillights are suitable for those who do not want to invest large sums in tuning their cars.
Vinyl wrap: features
This method will take much less time than the previous option. Also, this method is less laborious than in the case of staining. But there is one point with which there can be certain difficulties. It is necessary to stick the film so that there are no folds on the surface. Among the benefits of using this method you can highlight the ability to quickly remove the film at any time. There are many shades. There are all colors (for example, the red tinted taillights look great). The shade can be matched to a specific vehicle.
Paint tinting: how to apply varnish or paint
If a decision is made to darken using paint, the first step is to purchase a special preparation. It is best to choose tinting varnishes. They are much more convenient to apply and use. The cost of these paints and varnishes can be quite high. But the result is worth it. To process two lanterns, just one can is enough. It is recommended to carry out work related to painting headlights in well-ventilated rooms. It is best to do this outdoors. Choose a clear but not too sunny day. 
Do-it-yourself tinting of the taillights using paints or varnishes is carried out in several stages. The first step is to dismantle the headlights. This will allow the varnish to lie on the surface as evenly as possible. Please note that then the lights will need to be installed back. This requires skills. 
Further, the surface of the glass or plastic of the lantern must be degreased. To do this, you can use traditional alcohol or use special products. After the end of the process, the headlamp is allowed to dry. Shake the can before spraying the paint and varnish composition. Further, the paint is applied as thin and even layer as possible. Then the headlamp is allowed to dry out a little. It is necessary to lay it in such a place that small debris and dust do not fall on the painted surface. Next, one more (or more) layer of paint is applied - while painting is necessary until then, so as not to exceed the norms of light transmission of the headlight. When the lanterns are completely dry, they should be polished to a mirror finish. Then the optics can be put back on the car and enjoy the result.
Tinting with film: instructions
The following tools will be needed for work: a building hair dryer, a fairly sharp knife, an alcohol solution and an ordinary spatula. The first step is to tint the rear lights to thoroughly clean the surface. The headlights are first cleaned by removing moisture from them. This can be done conveniently and effectively with a microfiber cloth. Also, experts recommend using special cleaning products. Then an alcohol solution is sprayed on the surface of the film and on the headlight. This is done in order to simplify the tinting process. 
Stretch the vinyl in order to lay flat and take the shape of the taillights. This is done by hand or using a hair dryer. The material needs to be heated, and then the film will become flexible. It is important not to overheat the vinyl. Otherwise, wrinkles will appear.
What's next
Now we have the most important stage of work. It is necessary to stretch the material with a spatula and stick the film on the headlights. If something goes over the edges, it is cut off with a knife. Reviews say that tinting the rear lights with foil with your hands should be done very carefully. It is possible to damage the flashlight and hands in the process. This completes the process, and you can enjoy the result.
Headlight tinting and fines
As all car owners know, the country has introduced a ban on too strong car glass tinting. This is to improve safety as visibility is reduced and the driver may not notice the brake light or turn signal. 
In general, the rear lights do not affect the view of the road situation in any way, however, if the toning is done incorrectly, then the car owner faces not only a fine, the amount of which is similar to the fine for tinted glass, but also the obstruction of the movement of other cars from behind. Driver reviews repeatedly confirm this.
The law allows you to drive a car with a white taillight. Other yellow, red and orange light fixtures are also allowed. Tinted taillights (Priora is no exception) can significantly change the shades of the lamp's radiation. Therefore, work should be done very carefully and carefully. Otherwise, you will have to pay a fine of 500 rubles. Inspectors often interpret this tuning as a vehicle malfunction. In the worst case, you can lose driving license for 6-12 months under clause 13 of Art. 12.5 of the Code of Administrative Offenses.
When using black taillights, an accident can occur, and in this case the driver who drives with toning will be to blame. Then you will have to pay not only the fine, but also the repair of the damaged car.
There is an option when you can protect yourself from fines and still drive a beautiful and spectacular car. Reviews of car owners say that for this you need to do blackout in a specialized salon. How much does the taillight tinting cost? The price in large cities of Russia is from one and a half thousand rubles, depending on the car model and the geometry of the headlight itself. This is a relatively small amount. But by paying it, you can protect yourself from traffic police inspectors and protocols. In practice, most often no one and no one will fine, especially if the headlights are tinted correctly and skillfully. In this case, the brightness of the glow practically does not decrease. If the inspector sees a gross violation, he can ask to fix the problem on the spot. Reviews say that it is easiest to do this with film.
Conclusion
As you can see, this tuning method can be performed independently with certain skills. If you do everything correctly and follow the instructions, then this will not be considered a violation.
